2002 OLDSMOBILE AURORA lock

3-5
In cold weather, the system will delay turning on the fan
to avoid blowing cold air into the vehicle. The length of
the delay depends on the engine coolant temperature and
the outside temperature. Turning the right mode knob
will override this delay by turning off the automatic
mode and changing the fan speed.
Your automatic electronic climate control system has a
sun sensor located on the top of the instrument panel
that detects direct sunlight. To keep you and your
passengers comfortable, the system may supply cooler
air to the side of the vehicle toward the sun. Be careful
not to put anything over this sun sensor. The automatic
electronic climate control system may not operate
correctly if this sensor is covered.
To change the automatic electronic climate control
display from an English display to a metric display, push
the OFF button located in the Driver Information Center
(DIC) for two seconds. The display in the DIC will also
change from an English to a metric display. To return to
an English display, repeat the above procedure.Passenger Temperature Control (Option)
With this feature, the right
front seat passenger can
control the temperature
setting for his or her own
zone. To use this feature,
turn the knob on the
passenger's door clockwise
or counterclockwise to a
cooler or warmer setting.
The temperature can be set up to 8
F (4
C) cooler or
warmer than the main setting.
ProCarManuals.com

3-6 Comfort Controls Personalization
(If Equipped)
This feature enables up to two drivers to store and recall
comfort control settings for temperature, air delivery
mode and fan speed.
The memory buttons (1 or 2) for this feature are located
on the driver's door panel and correspond to the
numbers (1 or 2) found on the back of each remote
keyless entry transmitter.
To recall comfort settings, press the unlock button
on the remote keyless entry transmitter and put the
ignition in ACC (Accessory) or ON. The climate
control setting last chosen by the identified
driver (1 or 2) will be recalled.
To program a personal climate control setting, do
the following:
1. Choose a climate control setting for the driver
and if desired, for the passenger. See ªAutomatic
Electronic Climate Controlº and ªPassenger
Temperature Control (Option)º earlier in this section.
2. Adjust the direction of the airflow.3. Locate the memory buttons on the driver's
door panel.
4. Press a memory button (1 or 2) until you hear two
beeps. The beeps confirm that your selection has
been saved and can now be recalled.
Follow these steps each time you want to change the
stored settings. For more information on the memory
feature, see ªMemory Seat and Mirrorsº in the Index.
Air Conditioning
The air conditioner cools and dehumidifies the air inside
of the vehicle.
The air conditioning compressor is enabled in all
modes unless the air conditioning button is not selected
(the indicator light will not be illuminated). However,
the air conditioning compressor will not operate when
the outside temperature is below 34
F (1
C). When the
air conditioner is on, you may sometimes notice slight
changes in your vehicle's engine speed and power. This
is normal, because the system is designed to cycle the
compressor on and off to maintain the desired
temperature and to help with fuel economy.
ProCarManuals.com

3-7
On very hot days, open the windows long enough to let
the hot air out. This reduces the time required to cool the
interior of the vehicle to a comfortable temperature. If
the system is in the automatic mode (left and right mode
knob indicator lights are on), during very hot days the
system will automatically go to the recirculation mode
and the temperature door will initially be at the full cold
position for maximum cooling. You can choose the
extreme temperature setting of 60
F (16
C), but the
system will not cool any faster by choosing this setting.
Heating
In cold weather, if the automatic mode is selected
(left and right mode knob indicator lights are on), the
system will automatically direct the airflow out of the
floor ducts and the temperature door will initially be
positioned at the full hot position. You can choose
the extreme temperature setting of 90
F (32
C),
but the system will not warm up any faster by selecting
this setting.In cold weather, the system will delay turning on the fan
to avoid blowing cold air into the vehicle. The length of
the delay depends on the engine coolant temperature and
the outside temperature. The fan speed will increase as
the temperature of the engine coolant rises. Turning the
right mode knob will override this delay by cancelling
the automatic fan control mode.
Defogging and Defrosting
On cool, humid days, use the defog setting to keep
the windows clear while also providing heat through
the floor ducts. Turn the left mode knob clockwise
to defrost to quickly remove fog or ice from
the windshield.
For maximum front defrost performance under extreme
icing or frosting conditions, increase the temperature
setting to 90
F (33
C) and increase the fan speed
to high.
ProCarManuals.com

3-10 Steering Wheel Controls for
Climate Control
Some heating and cooling
controls can be adjusted
at the steering wheel.
Other touch controls
also operate some audio
controls. See ªAudio
Steering Wheel Controlsº
later in this section.
~!(Fan): Press the up arrow on the fan button to
override the automatic fan control and increase the fan
speed in manual mode. Press the down arrow on the fan
button to override the automatic fan control and reduce
the fan speed in manual mode.
~TEMP! (Temperature): Press either arrow on the
TEMP button once to display your current temperature
setting in the digital display. Press the up arrow on the
TEMP button again to provide a warmer temperature
setting or press the down arrow on the TEMP button
again to provide a cooler temperature setting.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off. See
ªRetained Accessory Power (RAP)º in the Index.
Setting the Clock
Press and hold HR until the correct hour appears. The
letters AM or PM will appear on the display. Then, press
and hold MN until the correct minute appears. The clock
may be set with the ignition on or off.
To set the clock to the time of an FM station
broadcasting Radio Data System (RDS) information,
press and hold HR and MN at the same time until
UPDATED appears on the display. If the time is not
available from the station, NO UPDATE will appear on
the display instead.
ProCarManuals.com

3-11 AM-FM Stereo with Cassette Tape and
Compact Disc Player with Programmable
Equalization and Radio Data System (RDS)
Standard Radio -- Bose
Not Shown
Playing the Radio
POWER: Press this knob to turn the system on and off.
VOLUME: Turn the knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.SCV (Speed
-Compensated Volume): With SCV, your
audio system adjusts automatically to make up for road
and wind noise as you drive. Set the volume at the
desired level. Press this button to select MIN, MED or
MAX. Each higher choice allows for more volume
compensation at faster vehicle speeds. Then, as you
drive, SCV automatically increases the volume, as
necessary, to overcome noise at any speed. The volume
level should always sound the same to you as you drive.
If you don't want to use SCV, select OFF.
Finding a Station
BAND: Press this button to switch between AM, FM1
and FM2. The display shows your selection.
TUNE: Turn this knob to select radio stations.
SEEK : Press the right or left arrow to go to the
next or previous station and stay there. The radio will
seek to stations with a strong signal only. The sound will
mute while seeking.
SCAN : Press and hold either arrow for two
seconds until SC appears on the display and you hear
a beep. The radio will go to a station, play for a few
seconds, then go on to the next station. Press either
SCAN arrow again to stop scanning. The radio will
scan to stations with a strong signal only. The sound will
mute while scanning.
ProCarManuals.com

3-14
Finding a PTY Preset Station
To find a PTY preset station, perform the following steps:
1. Press the P
-TYPE button to turn on PTY select. PTY
will be displayed and the light next to the button will
turn on. The last selected PTY will appear on the
display for five seconds.
2. Turn the P
-TYPE knob clockwise or
counterclockwise to select the PTY you want to
listen to. The list is alphabetical. If you select ANY
TYPE your radio will seek to the first PTY available.
3. Press the right SEEK arrow to find radio stations for
that PTY. The radio will seek to the first RDS
broadcaster of the selected program type. If the radio
cannot find the desired program type, NOT FOUND
will appear on the display and the radio will return to
the last station you were listening to. If both P
-TYPE
and TRAF are on, the radio will search for stations
with traffic announcements and the selected PTY.To use the P
-TYPE interrupt feature, press and hold the
P
-TYPE button until you hear a beep on the PTY you
want to interrupt on. An asterisk will appear next to the
PTY name (for example CLASSICAL*). When you are
listening to a cassette or compact disc, the last selected
RDS FM station will interrupt play if that selected PTY
format is broadcast.
BAND (Alternate Frequency): Alternate frequency
allows the radio to switch to a stronger station with the
same program type. Press and hold BAND for two
seconds to turn alternate frequency on. AF ON will
appear on the display. The radio may switch to stronger
stations. Press and hold BAND again for two seconds to
turn alternate frequency off. AF OFF will appear on the
display. The radio will not switch to other stations. When
you turn the ignition off and then on again, the alternate
frequency feature will automatically be turned on.
SEEK : Press the right arrow to go to a station with
the last selected PTY; TYPE and the last selected PTY
will appear on the display, if it is not already showing.
Press SEEK a second time to seek. If a station with the
selected PTY is not found, the radio will return to the
original station and display NONE.
ProCarManuals.com

3-17
SEEK : Press the right or left arrow to search for
the next or previous selection on the tape. Your tape
must have at least three seconds of silence between each
selection for seek to work. You can skip nine selections
forward or backward on the tape. Choose how many
selections you want to skip. Press the right or left SEEK
arrows that many times. The number of selections to be
skipped will appear on the display.
SCAN : Press and hold either arrow for more than
two seconds until you hear a beep and SCAN appears on
the display. The tape will go to the next selection, play
for a few seconds, then go on to the next selection. Press
this button again to stop scanning.
BAND: Press this button to listen to the radio when a
cassette tape is playing. The tape will stop but remain in
the player.
TP CD (TAPE): Press this button to play to play a
cassette tape or a CD when listening to the radio. Press
TP CD to switch between the tape and compact disc if
both are loaded. The inactive tape or CD will remain
safely inside the radio for future listening. The display
will show the TAPE and CD symbols.If you have the optional CD changer and it is loaded,
the TP CD button will activate the changer and a symbol
will be lit on the display.
(Eject): Press this button, located next to the
cassette tape slot, to eject a tape. Eject may be activated
with either the ignition or radio off. Cassettes may be
loaded with the radio and ignition off if this button is
pressed first.
Cassette Tape Messages
If an error occurs while trying to play a cassette tape,
it could be for one of the following reasons:
TIGHT TAPE: When this message is displayed, the
tape is tight and the player can't turn the tape hubs.
Remove the tape. Hold the tape with the open end down
and try to turn the right hub counterclockwise with a
pencil. Turn the tape over and repeat. If the hubs do not
turn easily, your tape may be damaged and should not be
used in the player. Try a new tape to make sure your
player is working properly.
BROKEN TAPE: If this message is displayed, the tape
is broken. Try a new tape.
ProCarManuals.com

3-21 Trunk-Mounted CD Changer (Option)
With the optional compact disc changer, you can play up
to 12 discs continuously. Normal size discs may be
played using the trays supplied in the magazine.
The small discs (8 cm) can be played only with specially
designed trays.
NOTICE:
Place large objects in the truck appropriately so
that they will not come into contact with the CD
changer. Damage could result that wouldn't be
covered by your warranty.
You must first load the magazine with discs before you
can play a compact disc. Each of the 12 trays holds one
disc. Slide the button on the back of the magazine and
pull gently on one of the trays. Load the trays from
bottom to top, placing a disc on the tray label side down.
If you load a disc label side up, the disc will not play
and an error will occur. Gently push the tray back into
the magazine slot until it locks into place. Repeat this
procedure for loading up to 12 discs in the magazine.
ProCarManuals.com