Page 269 of 373
6-13
A. Engine Compartment Fuse Block
B. Windshield Washer Fluid Reservoir
C. Engine Coolant Surge Tank
D. Remote Positive (+) Terminal
E. Heavy, Unpainted Metal Engine Part
F. Passenger Compartment Air FilterG. Power Steering Fluid Reservoir
H. Engine Oil Fill Cap
I. Engine Oil Dipstick
J. Automatic Transaxle Fluid Dipstick
K. Brake Fluid Reservoir
L. Engine Air Cleaner/Filter
ProCarManuals.com
Page 271 of 373
6-15
A. Engine Compartment Fuse Block
B. Windshield Washer Fluid Reservoir
C. Engine Coolant Surge Tank
D. Remote Positive (+) Battery Terminal
E. Power Steering Fluid Reservoir
F. Passenger Compartment Air Filter
G. Remote Negative (
-) Terminal
H. Engine Oil Fill Cap
I. Engine Oil Dipstick
J. Brake Fluid Reservoir
K. Automatic Transaxle Fluid Dipstick
(near the air cleaner)
L. Engine Air Cleaner/Filter
Engine Oil
If the CHECK OIL LEVEL message appears on the
instrument cluster, it means you need to check your
engine oil level right away. For more information, see
ªDIC Warnings and Messagesº in the Index.
You should check your engine oil level regularly; this is
an added reminder.
ProCarManuals.com
Page 279 of 373

6-23
To check or replace the air filter, do the following:
1. With the hood open, unlatch and remove the
access panel.
2. To remove the filter, press on the spring tab on
the side of the filter housing and pull the filter out
of the housing.
3. To install the new filter, press on the spring tab and
insert the filter into the housing. The filter should be
fully inserted into the upper and lower grooves and
locked into place by the spring tab.
4. Reinstall the air filter access panel at the base of
the windshield.Automatic Transaxle Fluid
When to Check and Change
A good time to check your automatic transaxle fluid
level is when the engine oil is changed.
Change both the fluid and filter every 50,000 miles
(83 000 km) if the vehicle is mainly driven under one or
more of these conditions:
In heavy city traffic where the outside temperature
regularly reaches 90F (32C) or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police or delivery service.
If you do not use your vehicle under any of
these conditions, change the fluid and filter
at 100,000 miles (166 000 km).
See ªScheduled Maintenance Servicesº in the Index.
ProCarManuals.com
Page 296 of 373
6-40
3. Disconnect the wiring harness from the
headlamp assembly.4. Lift the tabs to remove the bulb from the assembly.
5. Replace the bulb.
6. Push the bulb assembly in and turn it
clockwise to install the bulb assembly into the
headlamp assembly.
7. Then reconnect the wiring harness to the
lamp assembly.
ProCarManuals.com
Page 301 of 373
6-45
5. Turn the vertical
aiming screw (C)
until the headlamp
beam is aimed to
the horizontal
tape line.
The top edge of the cut
-off should be positioned at
the bottom edge of the horizontal tape line.
6. Repeat steps 4 and 5 for the opposite headlamp.
Front Turn Signals and Parking Lamps
Once the headlamp assembly has been removed from
the vehicle, the front turn signal and parking lamps can
be accessed. See ªHeadlampsº in the Index for more
information on location.
1. Tip the headlamp assembly and while pressing the
release, turn the bulb and socket counterclockwise to
remove them.
2. Replace the bulb in the socket.
3. Then reconnect the socket wiring harness to the
lamp assembly.
4. Reinstall the headlamp assembly into the vehicle.
ProCarManuals.com
Page 302 of 373
6-46 Rear Turn Signals, Stoplamps, Taillamps
and Back-up Lamps
1. Open the trunk.
2. Turn the screws located inside of the trunk
counterclockwise and remove them.
3. Remove the plastic trim piece from the trunk.
4. Pull the carpeting away from the rear corner of
the trunk.
5. Remove the three nuts holding the lamp in place and
remove the lamp assembly.
6. While pressing the release, turn the bulb socket
assembly counterclockwise to remove it from the
lamp assembly.
7. Pull the bulb straight out to remove it from
the socket.
8. Replace the bulb and reverse the steps to reinstall the
lamp assembly.
ProCarManuals.com
Page 303 of 373
6-47
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected at least
twice a year for wear or cracking. See ªWiper Blade
Checkº in the Index for more information.
To replace the wiper blade assembly, do the following:
1. Lift the wiper arm up from the windshield and set it
in the vertically locked position.
2. Push the tab on the wiper blade assembly and
pull the assembly down enough to release it from
the ªUº hooked end of the wiper arm. Slide the
assembly away from the arm.
3. Remove the blade.
4. To reinstall the wiper blade assembly, slide it over
the wiper arm to engage the ªUº hooked end on the
wiper blade assembly. Pull up on the assembly to
lock it into place.
For the proper windshield wiper blade assembly
replacement length and type, see ªNormal Maintenance
Replacement Partsº in the Index.
ProCarManuals.com
Page 306 of 373

6-50 Check Tire Pressure System
The check tire pressure system can alert you to a large
change in the pressure of one tire. The system won't
alert you before you drive that a tire is low or flat.
You must begin driving before the system will
work properly.
The LOW TIRE PRESSURE message will appear on
the Driver Information Center (DIC) if pressure
difference (low pressure) is detected in one tire. The
check tire pressure system may not alert you if:
more than one tire is low,
the vehicle is moving faster than 65 mph (105 km/h),
the system is not yet calibrated,
the tire treadwear is uneven,
the compact spare tire is installed,
tire chains are being used, or
the vehicle is being driven on a rough or frozen road.If the anti
-lock brake system warning light comes on,
the check tire pressure system may not be working
properly. See your dealer for service. Also, see
ªAnti
-Lock Brake System Warning Lightº in the Index.
The check tire pressure system detects differences in
tire rotation speeds that are caused by changes in tire
pressure. The system can alert you about a low
tire
-- but it doesn't replace normal tire maintenance.
See ªTiresº in the Index.
When the LOW TIRE PRESSURE message appears on
the Driver Information Center, you should stop as soon
as you can and check all your tires for damage. If a tire
is flat, see ªIf a Tire Goes Flatº in the Index. Also check
the tire pressure in all four tires as soon as you can. See
ªInflation
-Tire Pressureº in the Index.
Any time you adjust a tire's pressure or have one or
more tires repaired or replaced, you'll need to reset
(calibrate) the check tire pressure system. You'll also
need to reset the system whenever you rotate the tires,
buy new tires and install or remove the compact spare.
ProCarManuals.com