2002 NISSAN TERRANO lock

ASSEMBLY
1. Install snap ring onto forward clutch hub.
2. Install end bearing.
3. Install forward one-way clutch onto clutch hub.
IInstall forward one-way clutch with flange facing rearward.
4. Install end bearing.
5. Install snap ring onto forward clutch hub.
6. Install thrust washer onto rear internal gear.
IApply petroleum jelly to thrust washer.
ISecurely insert pawls of thrust washer into holes in rear
internal gear.
7. Position forward clutch hub in rear internal gear.
8. After installing, check to assure that forward clutch hub rotates
clockwise.
SAT901A
SAT904A
SAT906A
SAT907A
SAT905A
REPAIR FOR COMPONENT PARTS
Rear Internal Gear and Forward Clutch Hub
(Cont'd)
AT-170

Band Servo Piston Assembly
DISASSEMBLY
1. Block one oil hole in OD servo piston retainer and the center
hole in OD band servo piston.
2. Apply compressed air to the other oil hole in piston retainer to
remove OD band servo piston from retainer.
3. Remove D-ring from OD band servo piston.
4. Remove band servo piston assembly from servo piston retainer
by pushing it forward.
5. Place piston stem end on a wooden block. While pushing servo
piston spring retainer down, remove E-ring.
SAT908AC
SAT909A
SAT910A
SAT911A
REPAIR FOR COMPONENT PARTS
AT-171

6. Place piston stem end on a wooden block. While pushing servo
piston spring retainer down, install E-ring.
7. Install band servo piston assembly onto servo piston retainer by
pushing it inward.
8. Install D-ring on OD band servo piston.
IApply ATF to D-ring.
9. Install OD band servo piston onto servo piston retainer by push-
ing it inward.
SAT921A
SAT922A
SAT923A
SAT924A
REPAIR FOR COMPONENT PARTS
Band Servo Piston Assembly (Cont'd)
AT-174

Assembly (1)
1. Install manual shaft components.
a. Install oil seal onto manual shaft.
IApply ATF to oil seal.
IWrap threads of manual shaft with masking tape.
b. Insert manual shaft and oil seal as a unit into transmission
case.
c. Remove masking tape.
d. Push oil seal evenly and install it onto transmission case.
e. Align groove in shaft with drive pin hole, then drive pin into
position as shown in figure at left.
f. Install detent spring and spacer.
g. While pushing detent spring down, install manual plate onto
manual shaft.
h. Install lock nuts onto manual shaft.
SAT931A
SAT932A
SAT933A
SAT901E
SAT936A
ASSEMBLY
AT-177

d. Install band servo retainer onto transmission case.
4. Install rear side clutch and gear components.
a. Place transmission case in vertical position.
b. Slightly lift forward clutch drum assembly. Then slowly rotate it
clockwise until its hub passes fully over clutch inner race inside
transmission case.
c. Check to be sure that rotation direction of forward clutch
assembly is correct.
d. Install thrust washer onto front of overrun clutch hub.
IApply petroleum jelly to the thrust washer.
IInsert pawls of thrust washer securely into holes in over-
run clutch hub.
SAT940A
NAT303
SAT944A
SAT945A
SAT946A
ASSEMBLY
Assembly (1) (Cont'd)
AT-179

d. While rotating forward clutch drum clockwise, install front plan-
etary carrier on forward clutch drum.
ICheck that portion A of front planetary carrier protrudes
approximately 2 mm (0.08 in) beyond portion B of forward
clutch assembly.
e. Make sure bearing races are on front and rear of clutch pack.
IApply petroleum jelly to bearing races.
ISecurely engage pawls of bearing races with holes in
clutch pack.
f. Install clutch pack into transmission case.
SAT969A
SAT970A
SAT971A
SAT220B
ASSEMBLY
Assembly (1) (Cont'd)
AT-184

c. While holding anchor end pin, tighten lock nut.
8. Install terminal cord assembly.
a. Install O-ring on terminal cord assembly.
IApply petroleum jelly to O-ring.
b. Compress terminal cord assembly stopper and install terminal
cord assembly on transmission case.
9. Install control valve assembly.
a. Install accumulator piston return springsq
B,qCandqD.
Free length of return springs:
Refer to SDS, AT-197.
b. Install manual valve on control valve.
IApply ATF to manual valve.
c. Place control valve assembly on transmission case. Connect
solenoid connector for upper body.
d. Install connector clip.
SAT002B
SAT115B
SAT004BA
SAT005B
SAT006B
ASSEMBLY
Assembly (2) (Cont'd)
AT-191

General Specifications
Applied model TD27ETi engine
Automatic transmission model RE4R01A
Transmission model code number 4GX07
Stall torque ratio 2.0 : 1
Transmission gear ratio
1st 2.785
2nd 1.545
Top 1.000
OD 0.694
Reverse 2.272
Recommended fluidGenuine Nissan ATF or equiva-
lent*1
Fluid capacity
(Imp qt)8.5 (7-1/2)
*1: Refer to MA section (ªFluids and Lubricantsº, ªRECOMMENDED
FLUIDS AND LUBRICANTSº).
Specifications and Adjustment
SHIFT SCHEDULE
Vehicle speed when shifting gears
Throttle positionVehicle speed km/h (MPH)
D1,D2D2,D3D3,D4D4,D3D3,D2D2,D112,11
Full throttle32-36
(20 - 23)66-74
(41 - 46)108 - 118
(68 - 74)103 - 113
(64 - 71)61-69
(38 - 43)27-31
(17 - 19)43-47
(27 - 29)
Half throttle30-34
(19 - 21)62-68
(39 - 43)82-92
(51 - 58)67-75
(42 - 47)26-32
(16 - 20)7-11
(4-7)43-47
(27 - 29)
Vehicle speed when performing and
releasing lock-up
Throttle
positionOverdrive con-
trol switch
[Shift position]Vehicle speed km/h (MPH)
Lock-up
ªONºLock-up
ªOFFº
Full throttleON
[D
4]121 - 129
(76 - 81)116 - 124
(73 - 78)
OFF
[D
3]74-82
(46 - 51)74-82
(46 - 51)
Half throttleON
[D
4]104 - 112
(65 - 70)93 - 101
(58 - 63)
OFF
[D
3]74-82
(46 - 51)74-82
(46 - 51)
STALL REVOLUTION
Stall revolution rpm 2,450 - 2,700
LINE PRESSURE
Engine speed
rpmLine pressure kPa (bar, kg/cm2, psi)
D, 2 and 1 positions R position
Idle422 - 461
(4.22 - 4.61,
4.3 - 4.7,
61 - 67)589 - 627
(5.89 - 6.27,
6.01 - 6.40,
85.4 - 90.9)
Stall1,020 - 1,098
(10.20 - 10.98,
10.4 - 11.2,
148 - 159)1,422 - 1,500
(14.22 - 15.00,
14.5 - 15.3,
206 - 218)
SERVICE DATA AND SPECIFICATIONS (SDS)
AT-196