2002 MAZDA MODEL 626 light

8-35
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Yo u r v e h i c l e’s electrical system is
protected by fuses.
If any lights, accessories, or controls don ’t
work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted.
If the same fuse blows again, avoid using
that system and consult an Authorized
Mazda Dealer as soon as possible.





Fuse Replacement
If the electrical system doesn ’t work, first
inspect fuses on the driver ’s side.
1. Turn off the ignition switch and other switches.
2. Open the fuse panel cover.
3. Pull the fuse straight out . 4. Inspect it and replace if it
’s blown.
5. Push in a new fuse of the same rating, and make sure it fits tightly. If it
doesn ’t, have an Authorized Mazda
Dealer install it.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the RADIO circuit.
Fuses
Fuse panel cover
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system.
Normal Blown
CAUTION
J94S.book Page 35 Saturday, June 23, 2001 1:04 PM

8-36
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
If the headlights or other electrical
components don’t work and the fuses in
the cabin are OK, inspect the fuse block
under the hood. If a fuse is blown, it must
be replaced. Follow these steps:
1. Turn off the ignition switch and all
other switches.
2. Remove the fuse block cover.
3. If a fuse is blown, replace it with a new one of the same rating . When replacing the 100A fuse:
1. Turn off the ignition switch.
2. Remove the negative battery terminal.
3. Remove the A nuts.
4. Lift the fuse block and remove the B
bolts.
5. Replace the fuse with a new one of the
same rating .
6. Install in the reverse order of removal.
Fuse block cover
Normal Blown
B
A
A
A
B
B BA
100A fuse
J94S.book Page 36 Saturday, June 23, 2001 1:04 PM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G





Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1EGI INJ 30A Fuel injection
system
2 DEFOG 40A Rear window
defroster
3 —— —
4 MAIN 100A For protection of
all circuits
5 IG KEY 30A RADIO,
SUNROOF,
TURN, METER, ENGINE,
POWER
WINDOW,
WIPER fuses,
Ignition system
6 HEATER 40A Heater, Air
conditionerDESCRIPTION FUSE
RATING PROTECTED
COMPONENT
7 BTN 40A TAIL, STOP,
ROOM, DOOR LOCK,
HAZARD,
POWER SEAT fuses
8 COOLING
FA N 30A Cooling fan
9 AD FAN 30A Additional fan
10 (ABS) 60A Antilock brake
system
11 TAIL 15A Taillights,
Parking lights, Dashboard
illumination,
License plate
lights, Switches illumination
12 HORN 15A Horn
J94S.book Page 37 Saturday, June 23, 2001 1:04 PM

8-38
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
DESCRIPTIONFUSE
RATING PROTECTED
COMPONENT
13 (ABS) 20A Antilock brake
system
14 —— —
15 —— —
16 H/L-L 15A Headlight (Left)
17 H/L-R 15A Headlight
(Right)
18 (ABS) 20A Antilock brake
system
J94S.book Page 38 Saturday, June 23, 2001 1:04 PM

8-39
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Fuse panel (Driver’s side)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1 AUDIO 15A Audio system
2 ROOM 15A Interior lights,
Trunk light
3 S.ROOF 15A Sunroof
4 METER 10A Gauges, Reverse
lights
5 D.LOCK 30A Power door lock
6 HAZARD 15A Hazard warning
lights
7A/B&ABS 10A Air bag system,
Antilock brake system
8 —— —
9 A/C 10A Air conditioner
10 —— —
11 TURN 10A Turn signals
12 WIPER 20A Windshield
wipers and washer
13 P.WIND 30A Power windows
14 —— —DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
15 RADIO 15A Audio system,
Socket, Outside mirror
16 ENGINE 10A Engine control
system
17 ILLUMI 10A Taillights,
License plate
lights, Parking
lights, Dashboard illumination
18 STOP 15A Brake lights,
Horn, Cruise control
19 CIGAR 15A Accessory
socket, Clock,
Radio, Outside mirror
20 —— —
21 —— —
22 P.SEAT 30A Power seat
23 M.DEF 15A Mirror defroster
24 P.POINT 15A Power point
J94S.book Page 39 Saturday, June 23, 2001 1:04 PM

8-43
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for metallic, mica, and solid colors. 3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.





Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.





Bright-Metal Maintenance
• Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
• To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
• During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn ’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J94S.book Page 43 Saturday, June 23, 2001 1:04 PM

8-44
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G





Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.





Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
Don
’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
NOTE
• Don ’t use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
• Only use a mild soap or neutral
detergent and always use a sponge
or soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean
the wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
• Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
• If your aluminum wheels lose
luster, wax the wheels.
WARNING
J94S.book Page 44 Saturday, June 23, 2001 1:04 PM

10-6
Specifications
Form No. 8Q50-EA-01G





Air Conditioner






Light Bulbs






Tires
Standard tire
Temporary spare tire
Fuses ................................................................................................................ Refer to 8-35
Gas complies with SAE J639 R-134a
Maximum operating charge 0.75 kg (26.5 oz)
Light bulb Wattage
Headlights 60/55
Front turn signal/Parking lights 27/8
Rear-turn signal lights 27
Brake lights/Taillights 27/7
High-mount brake lights 27
Reverse lights 18
License plate lights 5
Trunk light 5
Interior lights 10
Map light 5
Courtesy lights 5
Item
Ty p e Tire size
Inflation pressure kgf/cm
2(psi or lb/po 2)
Front Rear
2.0-liter engine P205/60R15 90H 2.2 (32)1.8 (26)
2.5-liter engine P205/60R15 90H
P205/55R16 89H 2.0 (29)
Tire size Inflation pressure kPa (psi)
T125/70D15 420 (60)
J94S.book Page 6 Saturday, June 23, 2001 1:04 PM