2002 MAZDA 6 wiring

ON-BOARD DIAGNOSTIC
F2–95
F2
DTC P0097A6E407001082206
Diagnostic procedure
DTC P0097 IAT sensor No.1 circuit low input
DETECTION
CONDITION•PCM monitors input voltage from IAT sensor No.1 while engine is running. If input voltage from IAT sensor
No.1 is below 0.1 V, PCM determines IAT sensor No.1 circuit low input.
POSSIBLE
CAUSE•IAT sensor No.1 malfunction
•Connector or terminal malfunction
•Short to GND in wiring between MAF/IAT sensor terminal D and PCM terminal 60
•IAT sensor No.1 signal and GND circuits short each other
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF IAT
SENSOR NO.1 CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3CLASSIFY IAT SENSOR NO.1 MALFUNCTION
OR HARNESS MALFUNCTION
•Turn engine switch to ON (Engine OFF).
•Disconnect MAF/IAT sensor connector.
•Access IAT PID using WDS or equivalent.
•Is IAT PID below 0.1 V?Yes Go to next step.
No Replace MAF/IAT sensor, go to Step 7.
(See F2–36 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION)
4INSPECT IAT SENSOR NO.1 SIGNAL CIRCUIT
FOR SHORT TO GND
•Turn engine switch to OFF.
•Inspect continuity between MAF/IAT sensor
terminal D and body GND.
•Is there continuity?Yes Repair or replace harness for short to GND, go to Step 7.
No Go to next step.
D
E
2
24
5
5
6
660
91 IAT SENSOR NO.1PCM
ED
C
B
A
60 91 MAF/IAT SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–97
F2
DTC P0098A6E407001082207
Diagnostic procedure
DTC P0098 IAT sensor No.1 circuit high input
DETECTION
CONDITION•PCM monitors input voltage from IAT sensor No.1 while engine is running. If input voltage from IAT sensor
No.1 is above 5.0 V, PCM determines IAT sensor No.1 circuit high input.
POSSIBLE
CAUSE•IAT sensor No.1 malfunction
•Connector or terminal malfunction
•Short to power circuit in wiring between MAF/IAT sensor terminal D and PCM terminal 60
•Open circuit in wiring between MAF/IAT sensor terminal D and PCM terminal 60
•Open circuit in wiring between MAF/IAT sensor terminal E and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF IAT
SENSOR NO.1 CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3CLASSIFY IAT SENSOR NO.1 MALFUNCTION
OR HARNESS MALFUNCTION
•Turn engine switch to ON (Engine OFF).
•Connect jumper wire between MAF/IAT sensor
connector terminal D and E.
•Access IAT PID using WDS or equivalent.
•Is IAT PID below 1.0 V?Yes Replace MAF/IAT sensor, go to Step 7.
(See F2–36 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION)
No Go to next step.
D
E
2
246
65
560
91 IAT SENSOR NO.1PCM
9160 EDCB
A MAF/IAT SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–99
F2
DTC P0102A6E407001082208
Diagnostic procedure
DTC P0102 MAF sensor circuit low input
DETECTION
CONDITION•PCM monitors input voltage from MAF sensor while engine is running. If input voltage from MAF sensor is
below 0.2 V, PCM determines MAF sensor circuit low input.
POSSIBLE
CAUSE•MAF sensor malfunction
•Connector or terminal malfunction
•Open circuit in wiring between PCM control relay terminal C and MAF/IAT sensor terminal A
•Short to GND in wiring between MAF/IAT sensor terminal C and PCM terminal 9
•MAF sensor signal and GND circuits short each other
•Open circuit in wiring between MAF/IAT sensor terminal C and PCM terminal 9
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF MAF
SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 9.
No Go to next step.
3INSPECT MAF SENSOR POWER CIRCUIT FOR
OPEN
•Turn engine switch to ON. (Engine OFF)
•Inspect voltage at MAF/IAT sensor terminal A
(harness side).
•Is voltage below 1.0 V?Yes Repair or replace harness for open, go to Step 9.
No Go to next step.
2
2
2
3
4
5
58
7
76
MAF SENSOR PCM
EDC
BA
9
149
14 A
C
BPCM CONTROL RELAY
TERMINAL C
MAF SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–101
F2
DTC P0103A6E407001082209
Diagnostic procedure
DTC P0103 MAF sensor circuit high input
DETECTION
CONDITION•PCM monitors input voltage from MAF sensor while engine is running. If input voltage from MAF sensor is
above 4.9 V, PCM determines MAF sensor circuit high input.
POSSIBLE
CAUSE•MAF sensor malfunction
•Connector or terminal malfunction
•Short to power circuit in wiring between MAF/IAT sensor terminal C and PCM terminal 9
•MAF sensor power and signal circuits short each other
•Open circuit in wiring between MAF/IAT sensor terminal B and PCM terminal 14
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF MAF
SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 8.
No Go to next step.
3INSPECT MAF SENSOR SIGNAL CIRCUIT FOR
SHORT TO POWER
•Turn engine switch to ON. (Engine OFF)
•Inspect voltage between MAF/IAT sensor
terminal C and body GND.
•Is voltage below 1.0 V?Yes Go to next step.
No Repair or replace harness for short to power, go to Step 8.
4INSPECT MAF SENSOR CIRCUIT FOR SHORT
WITH EACH OTHER
•Turn engine switch to OFF.
•Inspect continuity between MAF/IAT sensor
terminals A and C.
•Is there continuity?Yes Repair or replace harness for short with each other, go to
Step 8.
No Go to next step.
MAF SENSOR
2
2
2
5
4
4
7
3
6
6
PCM
9
14 A
C
B
ED
CB
A
149 PCM CONTROL RELAY
TERMINAL C
MAF SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–103
F2
DTC P0107A6E407001082210
Diagnostic procedure
DTC P0107 Boost sensor circuit low input
DETECTION
CONDITION•PCM monitors input voltage from boost sensor while engine is running. If input voltage from boost sensor is
below 1.9 V when engine speed is 2,400 rpm or above and accelerator opening angle is 50% or above,
PCM determines boost sensor circuit low input.
POSSIBLE
CAUSE•Boost sensor malfunction
•Connector or terminal malfunction
•Short to GND in wiring between boost sensor terminal C and PCM terminal 90
•Open circuit in wiring between boost sensor terminal C and PCM terminal 90
•Short to GND in wiring between boost sensor terminal B and PCM terminal 36
•Boost sensor signal and GND circuits short each other
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF BOOST
SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 9.
No Go to next step.
3INSPECT BOOST SENSOR SIGNAL CIRCUIT
FOR SHORT TO GND
•Turn engine switch to OFF.
•Inspect continuity between boost sensor
terminal C and body GND.
•Is there continuity?Yes Repair or replace harness for short to GND, go to Step 9.
No Go to next step.
2
2
2
7
3
5
4
6
68
8
8
C
B
A90
36
91 BOOST SENSOR PCM
C
BA
91
9036
BOOST SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–105
F2
DTC P0108A6E407001082211
Diagnostic procedure
DTC P0108 Boost sensor circuit high input
DETECTION
CONDITION•PCM monitors input voltage from boost sensor while engine is running. If input voltage from boost sensor is
above 4.9 V, PCM determines boost sensor circuit high input.
POSSIBLE
CAUSE•Boost sensor malfunction
•Connector or terminal malfunction
•Boost sensor power and signal wiring short each other
•Open circuit in wiring between boost sensor terminal B and PCM terminal 36
•Open circuit in wiring between boost sensor terminal A and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF BOOST
SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3INSPECT BOOST SENSOR CIRCUIT FOR
SHORT WITH EACH OTHER
•Turn engine switch to OFF.
•Inspect continuity between boost sensor
terminals C and B
•Is there continuity?Yes Repair or replace harness for short with each other, go to
Step 7.
No Go to next step.
4INSPECT BOOST SENSOR
•Inspect boost sensor.
(See F2–78 BOOST SENSOR INSPECTION)
•Is there any malfunction?Yes Replace boost sensor, go to Step 7.
(See F2–36 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION)
No Go to next step.
2
C
B
A
C
BAPCM
90
36
91
919036 BOOST SENSOR
6
2
5
53
5
4
3
62
BOOST SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–107
F2
DTC P0112A6E407001082212
Diagnostic procedure
DTC P0112 IAT sensor No.2 circuit low input
DETECTION
CONDITION•PCM monitors input voltage from IAT sensor No.2 while engine is running. If input voltage from IAT sensor
No.2 is below 0.1 V, PCM determines IAT sensor No.2 circuit low input.
POSSIBLE
CAUSE•IAT sensor No.2 malfunction
•Connector or terminal malfunction
•Short to GND in wiring between IAT sensor No.2 terminal A and PCM terminal 8
•IAT sensor No.2 signal and GND circuits short each other
•PCM malfunction
462
4362
5
A
B8
91 IAT SENSOR NO.2
BA
918 PCM
IAT SENSOR NO.2
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF IAT
SENSOR NO.2 CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3INSPECT IAT SENSOR NO.2 SIGNAL CIRCUIT
FOR SHORT TO GND
•Turn engine switch to OFF.
•Inspect continuity between IAT sensor No.2
terminal A and body GND.
•Is there continuity?Yes Repair or replace harness for short to GND, go to Step 7.
No Go to next step.
4INSPECT IAT SENSOR NO.2 CIRCUIT FOR
SHORT WITH EACH OTHER
•Turn engine switch to OFF.
•Inspect continuity between IAT sensor No.2
terminals A and B.
•Is there continuity?Yes Repair or replace harness for short with each other, go to
Step 7.
No Go to next step.

ON-BOARD DIAGNOSTIC
F2–109
F2
DTC P0113A6E407001082213
Diagnostic procedure
DTC P0113 IAT sensor No.2 circuit high input
DETECTION
CONDITION•PCM monitors input voltage from IAT sensor No.2 while engine is running. If input voltage from IAT sensor
No.2 is above 5.0 V, PCM determines IAT sensor No.2 circuit high input.
POSSIBLE
CAUSE•IAT sensor No.2 malfunction
•Connector or terminal malfunction
•Short to power circuit in wiring between IAT sensor No.2 terminal A and PCM terminal 8
•Open circuit in wiring between IAT sensor No.2 terminal A and PCM terminal 8
•Open circuit in wiring between IAT sensor No.2 terminal B and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF IAT
SENSOR NO.2 CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3INSPECT IAT SENSOR NO.2 SIGNAL CIRCUIT
FOR SHORT TO POWER
•Turn engine switch to ON (Engine OFF).
•Inspect voltage between IAT sensor No.2
terminal A and body GND.
•Is voltage below 1.0 V?Yes Go to next step.
No Repair or replace harness for short to power, go to Step 7.
4INSPECT IAT SENSOR NO.2
•Inspect IAT sensor No.2.
(See F2–75 INTAKE AIR TEMPERATURE
(IAT) SENSOR NO.2 INSPECTION)
•Is there any malfunction?Yes Replace IAT sensor No.2, go to Step 7.
(See F2–36 INTAKE-AIR SYSTEM REMOVAL/
INSTALLATION)
No Go to next step.
562
5
4
362
IAT SENSOR NO.2
BAA
B8
91PCM
918 IAT SENSOR NO.2
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR