2002 LAND ROVER DISCOVERY engine oil

TORQUE WRENCH SETTINGS
06-4
Engine V8
TORQUE DESCRIPTION METRIC IMPERIAL
Engine mounting bolts (rear, LH & RH) to gearbox bolts 85 Nm (63 lbf.ft)
Engine mounting (rear, LH & RH) nuts 45 Nm (33 lbf.ft)
Cylinder head bolts tighten, then 90°, then a further 90°20 Nm (15 lbf.ft)
Rocker shaft bolts 40 Nm (30 lbf.ft)
Alternator mounting bracket 40 Nm (30 lbf.ft)
Auxiliary drive belt tensioner 45 Nm (33 lbf.ft)
Engine earth lead 22 Nm (16 lbf.ft)
Rocker cover bolts 8 Nm (6 lbf.ft)
Torque converter to drive plate 50 Nm (37 lbf.ft)
A/C compressor 22 Nm (16 lbf.ft)
ACE pump 22 Nm (16 lbf.ft)
Flywheel to crankshaft 78 Nm (58 lbf.ft)
Crankshaft sensor 6 Nm (5 lbf.ft)
Crankshaft sensor cover 6 Nm (5 lbf.ft)
Spacer and hub to crankshaft 85 Nm (63 lbf.ft)
Drive plate and clamp ring 45 Nm (33 lbf.ft)
Oil pick up strainer 10 Nm (7 lbf.ft)
Filter head adaptor 13 Nm (10 lbf.ft)
Filter head 8 Nm (6 lbf.ft)
Sump bolts 22 Nm (16 lbf.ft)
Oil pressure switch 15 Nm (11 lbf.ft)
Timing gear cover to cylinder block 22 Nm (16 lbf.ft)
Oil cooler pipe to timing gear cover 15 Nm (11 lbf.ft)
Crankshaft pulley bolt 270 Nm (200 lbf.ft)
Coolant outlet elbow 22 Nm (16 lbf.ft)
Auxiliary housing 40 Nm (30 lbf.ft)
Jockey pulley 50 Nm (37 lbf.ft)
Camshaft gear 50 Nm (37 lbf.ft)
Rocker shaft bolts 40 Nm (30 lbf.ft)
Connecting rod bolts
Final torque - turn through 80 °20 Nm (15 lbf.ft)
Initial torque - all main bearing cap bolts and side bolts 13.5 Nm (10 lbf.ft)
Final torque - main bearing cap side bolts 11 to 15 45 Nm (33 lbf.ft)
Final torque - main bearing cap bolts 1 to 8 72 Nm (53 lbf.ft)
Final torque - main bearing cap bolts 9 and 10 92 Nm (68 lbf.ft)
Final torque - main bearing cap side bolts 16 to 20 45 Nm (33 lbf.ft)
Viscous fan nut 45 Nm (33 lbf.ft)
Camshaft thrust plate bolts 22 Nm (16 lbf.ft)
Secondary Air Injection adapters 33 Nm (24 lbf.ft)

TORQUE WRENCH SETTINGS
06-5
Emission control - Td5
Emission control - V8
Engine management system - Td5
TORQUE DESCRIPTION METRIC IMPERIAL
EGR valve pipe Allen screws 10 Nm (7 lbf.ft)
EGR valve to inlet manifold bolts 10 Nm (7 lbf.ft)
EGR intake pipe clip to cylinder head bolts - if fitted 25 Nm (18 lbf.ft)
EGR cooler to cylinder head nut and bolts - if fitted 25 Nm (18 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
HO
2S Sensors45 Nm (33 lbf.ft)
SAI air manifold union nuts 25 Nm (18 lbf.ft)
Rubber mountings to SAI pump bracket 10 Nm (7 lbf.ft)
SAI control valve to manifold bolts 10 Nm (7 lbf.ft)
SAI pump to bracket nuts 10 Nm (7 lbf.ft)
SAI pump bracket to body bolt 20 Nm (15 lbf.ft)
Vacuum reservoir to mounting bracket bolt 10 Nm (7 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
ECT sensor15 Nm (11 lbf.ft)
Fuel tank cradle45 Nm (33 lbf.ft)
CKP sensor10 Nm (7 lbf.ft)
MAP and IAT sensor 10 Nm (7 lbf.ft)
Fuel cooler to inlet manifold - upper bolts 25 Nm (18 lbf.ft)
Turbocharger to exhaust manifold 30 Nm (22 lbf.ft)
Turbocharger drain pipe 10 Nm (7 lbf.ft)
Banjo bolt to oil feed pipe 25 Nm (18 lbf.ft)
Fuel temperature sensor 14 Nm (10 lbf.ft)
Pressure regulator 25 Nm (18 lbf.ft)
Glow plugs16 Nm (12 lbf.ft)
EUI clamp bolts32 Nm (24 lbf.ft)
EGR valve to exhaust manifold 10 Nm (7 lbf.ft)
EGR valve to inlet manifold 10 Nm (7 lbf.ft)
EGR clip25 Nm (18 lbf.ft)

TORQUE WRENCH SETTINGS
06-6
Engine management system - V8
Cooling system
Manifolds and exhaust systems - Td5
TORQUE DESCRIPTION METRIC IMPERIAL
Spark plugs20 Nm (15 lbf.ft)
Fuel tank cradle45 Nm (33 lbf.ft)
ECT sensor10 Nm (7 lbf.ft)
CKP sensor6 Nm (4.4 lbf.ft)
CMP sensor8 Nm (6 lbf.ft)
KS sensor22 Nm (16 lbf.ft)
Throttle body10 Nm (7 lbf.ft)
Plenum chamber22 Nm (16 lbf.ft)
Breather adaptor6 Nm (4.4 lbf.ft)
Throttle cable abutment bracket 10 Nm (7 lbf.ft)
TP sensor 2.2 Nm (1.6 lbf.ft)
IACV sensor8 Nm (6 lbf.ft)
HO
2S sensor45 Nm (33 lbf.ft)
Ignition coils8 Nm (6 lbf.ft)
Fuel rail9 Nm (7 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
Cylinder block drain plug 30 Nm (22 lbf.ft)
Coolant pump24 Nm (18 lbf.ft)
Coolant pump pulley 22 Nm (16 lbf.ft)
Coolant pump cover - Td5 10 Nm (7 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
Front pipe to turbocharger 27 Nm (20 lbf.ft)
Inlet manifold25 Nm (18 lbf.ft)
Tail pipe25 Nm (18 lbf.ft)
Fuel cooler25 Nm (18 lbf.ft)
EGR valve10 Nm (7 lbf.ft)
Exhaust manifold25 Nm (18 lbf.ft)
Exhaust manifold heatshield (M6) bolts 10 Nm (7 lbf.ft)
Exhaust manifold heatshield (M8) bolts 25 Nm (18 lbf.ft)
EGR pipe Allen screws 10 Nm (7 lbf.ft)

TORQUE WRENCH SETTINGS
06-8
Manual gearbox - R380
Transfer box - LT230SE
Note: † New Patchlok nut must be fitted.
TORQUE DESCRIPTION METRIC IMPERIAL
Bias plate bolts25 Nm (18 lbf.ft)
Gearbox to engine bolts 45 Nm (33 lbf.ft)
Coolant pipe housing bolts 25 Nm (18 lbf.ft)
Breather pipe banjo bolt 15 Nm (11 lbf.ft)
Gear lever extension clamp bolt 25 Nm (18 lbf.ft)
Gearbox mounting bolts 85 Nm (63 lbf.ft)
Gearbox mounting nuts 48 Nm (37 lbf.ft)
Seal housing bolts 18 Nm (13 lbf.ft)
Bearing sleeve bolts 25 Nm (18 lbf.ft)
Fork bolt7 Nm (5.2 lbf.ft)
Reverse light switch 24 Nm (18 lbf.ft)
Extension housing bolts 25 Nm (18 lbf.ft)
Gear selector housing bolts 25 Nm (18 lbf.ft)
Oil pump to housing Torx screws 6 Nm (4.4 lbf.ft)
Gear change lever yoke Allen screw 25 Nm (18 lbf.ft)
5th gear stake nut 350 Nm (258 lbf.ft)
Spool retainer bolts 8 Nm (6 lbf.ft)
Centre plate detent spring and ball Torx screw 25 Nm (18 lbf.ft)
Selector lever to housing bolts 25 Nm (18 lbf.ft)
Clutch Bell housing bolts 73 Nm (54 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
High/low selector cable 30 Nm (22 lbf.ft)
Bottom plate bolts 25 Nm (18 lbf.ft)
Transfer box to gearbox 45 Nm (33 lbf.ft)
Rear cover plate25 Nm (18 lbf.ft)
Differential lock warning lamp switch locknut - Up to 03 MY
11 Nm(8 lbf.ft)
Differential lock warning lamp switches - 03 MY onwards
25 Nm (18 lbf.ft)
Drive flange nut148 Nm (109 lbf.ft)
Output shaft housing 45 Nm (33 lbf.ft)
Oil temperature sensor 42 Nm (31 lbf.ft)
Inhibitor switch to transfer box 26 Nm (19 lbf.ft)
Intermediate shaft nut †88 Nm (65 lbf.ft)
Side cover bolts25 Nm (18 lbf.ft)
Bearing retaining nut 72 Nm (53 lbf.ft)
Output flange nut 162 Nm (119 lbf.ft)
Selector housing bolts 25 Nm (18 lbf.ft)
Bearing housing/cover bolts 25 Nm (18 lbf.ft)

TORQUE WRENCH SETTINGS
06-9
Automatic gearbox - ZF4HP22/24
Propeller shafts
Axles
TORQUE DESCRIPTION METRIC IMPERIAL
Selector lever to selector shaft nut 26 Nm (19 lbf.ft)
Starter inhibitor switch bolts 10 Nm (7 lbf.ft)
Engine to torque converter bolts - Td5 & V8 50 Nm (37 lbf.ft)
Closing plate to gearbox housing bolt - V8 7 Nm (5.2 lbf.ft)
Fluid pump to intermediate plate bolts 10 Nm (7 lbf.ft)
Intermediate plate Allen plugs (M14) 40 Nm (30 lbf.ft)
Intermediate plate Allen plugs (M20) 50 Nm (37 lbf.ft)
Oil cooler adaptors 42 Nm (31 lbf.ft)
Extension housing bolts 25 Nm (18 lbf.ft)
Oil sump to gearbox housing bolts 8 Nm (6 lbf.ft)
Oil filter Torx screws 8 Nm (6 lbf.ft)
Oil pick-up tube Torx screw 8 Nm (6 lbf.ft)
Parking pawl guide Torx screw 10 Nm (7 lbf.ft)
Pressure regulator to valve body assembly 8 Nm (6 lbf.ft)
Lock-up solenoid valve, retaining fork Torx screw 8 Nm (6 lbf.ft)
Lock-up solenoid valve assembly to valve body Torx screws 8 Nm (6 lbf.ft)
Gearbox bell housing (intermediate plate and converter housing to gearbox casing)
bolts46 Nm (34 lbf.ft)
Speed sensor bracket screws 8 Nm (6 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
Propeller shaft to transfer gearbox 47 Nm (35 lbf.ft)
Propeller shaft to differential 47 Nm (35 lbf.ft)
Propeller shaft to flexible coupling 76 Nm (56 lbf.ft)
Flexible coupling to differential 76 Nm (56 lbf.ft)
TORQUE DESCRIPTION METRIC IMPERIAL
Differential to axle bolts 55 Nm (40 lbf.ft)
Hub to axle bolts 100 Nm (74 lbf.ft)
Pinion flange bolt 100 Nm (74 lbf.ft)
Drive shaft nut490 Nm (360 lbf.ft)

LIFTING AND TOWING
08-2
Reverse procedure when removing vehicle from
stands.
Hydraulic ramps
Use only a 'drive on' type ramp which supports a
vehicle by it's own road wheels. If a 'wheel free'
condition is required, use a 'drive on' ramp
incorporating a 'wheel free' system that supports
under axle casings. Alternatively, place vehicle on a
firm, flat floor and support on axle stands.
TOWING
Towing
The vehicle has permanent four wheel drive. The
following towing instructions must be adhered
to:
Towing on 4 wheels with driver
Turn ignition key to position '1' to release steering
lock.
Select neutral in main gearbox and transfer gearbox.
Secure tow rope, chain or cable to towing eye.
Release the handbrake.
The brake servo and power assisted steering
system will not be functional without the engine
running. Greater pedal pressure will be required
to apply the brakes, the steering system will
require greater effort to turn the front road
wheels. The vehicle tow connection should be
used only in normal road conditions, 'snatch'
recovery should be avoided.Suspended tow
To prevent vehicle damage, front or rear
propeller shaft MUST BE removed, dependent
upon which axle is being trailed.
Mark propeller shaft drive flanges at transfer box and
axles with identification lines to enable the propeller
shaft to be refitted in its original position.
Remove the propeller shaft fixings, remove the shaft
from the vehicle.
If the front axle is to be trailed turn ignition key to
position '1' to release steering lock.
The steering wheel and/or linkage must be
secured in a straight ahead position. DO NOT use
the steering lock mechanism for this purpose.
Towing eyes
The towing eyes at the front and rear of the vehicle
are designed for vehicle recovery purposes only and
must NOT be used to tow a trailer or caravan.
Front:A single towing eye, set behind a removable
panel in the front spoiler. DO NOT use the front
lashing rings for towing.

CAPACITIES, FLUIDS AND LUBRICANTS
09-1
CAPACITIES, FLUIDS AND LUBRICANTS
Capacities
The following capacities are only an approximation of
the amount of fluid required to fill the respective
system.
Capacities - UK EURO ROW
Capacities - NAS
Component Metric Units
Fuel tank 95 litres
Engine - Td5:

Engine oil and filter change 7.2 litres

Fill from dry 8.2 litres
Engine - V8 with oil cooler:

Engine oil and filter change 6.27 litres

Engine oil refill from dry: 7 litres
Engine - V8 without oil cooler:

Engine oil and filter change 5.8 litres

Engine oil refill from dry 6.5 litres
Manual gearbox without oil cooler:

Refill 2.3 litres

Fill from dry 2.6 litres
Manual gearbox with oil cooler:

Refill 2.8 litres

Fill from dry 3.1 litres
Automatic gearbox fill from dry
9.7 litres
Transfer box:

Refill 2.0 litres

Fill from dry 2.3 litres
Front and rear axle:

Refill 1.6 litres

Fill from dry 1.7 litres
Cooling system - Td5 Engine:

Refill 8 litres

Fill from dry 13 litres
Cooling system - V8 Engine:

Refill 12 litres

Fill from dry 13 litres
Component US Units
Fuel tank25.5 gal
Engine - V8 with oil cooler:

Engine oil and filter change 6.6 qt

Engine oil refill from dry 7.4 qt
Engine - V8 without oil cooler:

Engine oil and filter change 6.1 qt

Engine oil refill from dry 6.9 qt
Automatic gearbox fill from dry
19.7 pt
Transfer box:

Refill4.1 pt

Fill from dry 4.8 pt
Front and rear axle:

CAPACITIES, FLUIDS AND LUBRICANTS
09-2
Refrigerant - A/C system
Fluids
Anti-freeze
Use Havoline Extended Life Coolant (XLC), or any
ethylene glycol based anti-freeze (containing no
methanol) with only Organic Acid Technology
corrosion inhibitors, to protect the cooling system
CAUTION: No other anti-freeze should be used
with Havoline Extended Life Coolant.
The cooling system should be drained, flushed and
refilled with the correct amount of anti-freeze solution
at the intervals given on the Service Maintenance
Check Sheet.
After filling with anti-freeze solution, attach a warning
label to a prominent position on the vehicle stating
the type of anti-freeze contained in the cooling
system to ensure that the correct type is used for
topping-up.
Brake/Clutch fluid
Use only DOT 4 brake fluid.
PAS/ACE fluid
Use Texaco cold climate power assisted steering
fluid 14315.
Air conditioning
Use only refrigerant R134a.
Refrigerant oil
Use only NipponDenso ND-oil 8 or Unipart ND-oil 8.
Refrigerant oil absorbs water and must not be stored
for long periods. Do not pour unused oil back into the
container.
NOTE: The total quantity of refrigerant oil in the
system is 180 ml.
CAUTION: Do not use any other type of
refrigerant oil.

Refill3.4 pt

Fill from dry 3.6 pt
Cooling system - V8 Engine:

Refill24.2 pt

Fill from dry 26.2 ptComponent US Units

Front A/C 700 ± 25 g

Front/rear A/C 900 ± 25 g