2002 JEEP LIBERTY fuse panel

BLOWER MOTOR
DESCRIPTION
The blower motor and blower wheel are located in
the passenger side end of the HVAC housing, below
the glove box. The blower motor controls the velocity
of air flowing through the HVAC housing by spinning
a squirrel cage-type blower wheel within the housing
at the selected speed. The blower motor and wheel
can be removed from the housing inside the vehicle
without removing the dash or HVAC housing assem-
bly.
OPERATION
The blower motor will only operate when the igni-
tion switch is in the On position, and the A/C Heater
mode control switch knob is in any position, except
Off. The blower motor receives a fused battery feed
through the blower motor relay whenever the igni-
tion switch is in the On position. The blower motor
battery feed circuit is protected by a fuse in the
Power Distribution Center (PDC). Blower motor
speed is controlled by regulating the ground path
through the A/C Heater control blower motor switch
and the blower motor resistor.
The blower motor and blower motor wheel cannot
be repaired and, if faulty or damaged, they must be
replaced. The blower motor and blower wheel are ser-
viced only as a unit.
DIAGNOSIS AND TESTING - BLOWER MOTOR
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
For circuit descriptions and diagrams, (Refer to
Appropriate Wiring Information). Possible causes of
an inoperative blower motor include:²Faulty fuse
²Faulty blower motor circuit wiring or wire har-
ness connectors
²Faulty blower motor resistor
²Faulty blower motor relay
²Faulty blower motor switch
²Faulty A/C Heater mode control switch
²Faulty blower motor.
Possible causes of the blower motor not operating
in all speeds include:
²Faulty blower motor switch
²Faulty blower motor resistor
²Faulty blower motor circuit wiring or wire har-
ness connectors.
VIBRATION
Possible causes of blower motor vibration include:
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower wheel out of balance or bent
²Blower motor faulty.
NOISE
To verify that the blower is the source of the noise,
unplug the blower motor wire harness connector and
operate the HVAC system. If the noise goes away,
possible causes include:
²Foreign material in the HVAC housing
²Improper blower motor mounting
²Improper blower wheel mounting
²Blower motor faulty.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
24 - 30 DISTRIBUTIONKJ

FUEL PRESSURE REGULATOR -
DESCRIPTION.......................14-13
FUEL PRESSURE REGULATOR -
INSTALLATION.......................14-14
FUEL PRESSURE REGULATOR -
OPERATION.........................14-14
FUEL PRESSURE REGULATOR -
REMOVAL..........................14-14
FUEL PUMP - DESCRIPTION............14-15
FUEL PUMP - OPERATION.............14-15
FUEL PUMP AMPERAGE TEST -
DIAGNOSIS AND TESTING.............14-16
FUEL PUMP CAPACITY TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP MODULE - DESCRIPTION....14-18
FUEL PUMP MODULE - INSTALLATION . . . 14-19
FUEL PUMP MODULE - OPERATION......14-18
FUEL PUMP MODULE - REMOVAL.......14-18
FUEL PUMP PRESSURE TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP RELAY - DESCRIPTION......14-34
FUEL PUMP RELAY - DIAGNOSIS AND
TESTING...........................14-34
FUEL PUMP RELAY - INSTALLATION.....14-34
FUEL PUMP RELAY - OPERATION........14-34
FUEL PUMP RELAY - REMOVAL.........14-34
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-4
FUEL RAIL - DESCRIPTION.............14-21
FUEL RAIL - INSTALLATION..............14-24
FUEL RAIL - OPERATION...............14-21
FUEL RAIL - REMOVAL................14-22
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-4
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-5
FUEL SYSTEM, SPECIAL TOOLS..........14-6
FUEL TANK - DESCRIPTION............14-24
FUEL TANK - INSTALLATION............14-27
FUEL TANK - OPERATION..............14-24
FUEL TANK - REMOVAL...............14-25
FUEL TANK CHECK VALVE -
DESCRIPTION.......................14-28
FUEL TANK CHECK VALVE -
INSTALLATION.......................14-28
FUEL TANK CHECK VALVE - OPERATION . . 14-28
FUEL TANK CHECK VALVE - REMOVAL....14-28
FUEL TANK SKID PLATE - INSTALLATION . . . 13-9
FUEL TANK SKID PLATE - REMOVAL......13-9
FULL TIME INDICATOR - DESCRIPTION . . . 8J-29
FULL TIME INDICATOR - OPERATION.....8J-30
FUNCTION - DIAGNOSIS AND TESTING,
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER..................8G-9
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-3
FUSE - INSTALLATION, IOD..........8W-97-3
FUSE - OPERATION, IOD.............8W-97-3
FUSE - REMOVAL, IOD..............8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-9
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL.....9-10
GAP AND FLUSH - SPECIFICATIONS.....23-116
GAS ENGINES - GENERATOR RATINGS....8F-23
GAS POWERED - STARTER MOTOR......8F-39
GAS POWERED - TORQUE
.............8F-38
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD
..................9-19,9-30
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE
.........9-9
GATE - INSTALLATION, SWING
.........23-138
GATE - REMOVAL, SWING
............23-138
GATE AJAR INDICATOR - DESCRIPTION
. . . 8J-20
GATE AJAR INDICATOR - OPERATION
.....8J-20
GATE BELTLINE WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE BELTLINE WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GATE OPENING WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE OPENING WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-18
GAUGE - DESCRIPTION, FUEL
...........8J-19GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-18
GAUGE - OPERATION, FUEL............8J-20
GEAR - DESCRIPTION.................19-13
GEAR - INSTALLATION, PINION
GEAR/RING..........................3-46
GEAR - OPERATION...................19-13
GEAR - REMOVAL, PINION GEAR/RING....3-44
GEAR/RING GEAR - INSTALLATION,
PINION.............................3-46
GEAR/RING GEAR - REMOVAL, PINION....3-44
GEAR/RING GEAR/TONE RING -
INSTALLATION, PINION............3-112,3-82
GEAR/RING GEAR/TONE RING -
REMOVAL, PINION...............3-110,3-79
GEARSHIFT CABLE - ADJUSTMENTS....21-130
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-128
GEARSHIFT CABLE - INSTALLATION.....21-129
GEARSHIFT CABLE - REMOVAL........21-128
GEAR/TONE RING - INSTALLATION,
PINION GEAR/RING...............3-112,3-82
GEAR/TONE RING - REMOVAL, PINION
GEAR/RING.....................3-110,3-79
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-160
GEARTRAIN - CLEANING, PLANETARY . . . 21-159
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-157
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-159
GEARTRAIN - INSPECTION, PLANETARY . 21-159
GEARTRAIN - OPERATION, PLANETARY . . 21-157
GENERAL - WARNINGS.............8W-01-7
GENERATOR - DESCRIPTION...........8F-25
GENERATOR - INSTALLATION...........8F-26
GENERATOR - OPERATION.............8F-25
GENERATOR - REMOVAL...............8F-25
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-27
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-26
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-30
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-27
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-27
GENERATOR RATINGS, GAS ENGINES....8F-23
GLASS - INSTALLATION, DOOR . . 23-122,23-129,
23-172
GLASS - INSTALLATION, FLIP-UP.......23-136
GLASS - REMOVAL, DOOR......23-122,23-129,
23-172
GLASS - REMOVAL, FLIP-UP..........23-136
GLASS AJAR INDICATOR - DESCRIPTION . . 8J-21
GLASS AJAR INDICATOR - OPERATION . . . 8J-21
GLASS AJAR SWITCH - DESCRIPTION,
FLIP-UP............................8L-77
GLASS AJAR SWITCH - OPERATION,
FLIP-UP............................8L-77
GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE, REAR..........8G-4
GLASS LATCH - INSTALLATION, FLIP-UP . 23-136
GLASS LATCH - REMOVAL, FLIP-UP.....23-136
GLASS PANEL - INSTALLATION........23-178
GLASS PANEL - REMOVAL............23-178
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-178
GLASS PANEL SEAL - INSTALLATION
....23-178
GLASS PANEL SEAL - REMOVAL
.......23-178
GLASS RELEASE SWITCH - DIAGNOSIS
AND TESTING, FLIP-UP
................8N-5
GLASS RUN CHANNEL - INSTALLATION
. 23-123,
23-130
GLASS RUN CHANNEL - REMOVAL
.....23-123,
23-130
GLASS SUPPORT CYLINDER -
INSTALLATION, FLIP-UP
..............23-139
GLASS SUPPORT CYLINDER -
REMOVAL, FLIP-UP
..................23-139
GLOVE BOX - INSTALLATION
..........23-148
GLOVE BOX - REMOVAL
..............23-148
GLOVE BOX LATCH - INSTALLATION
....23-148
GLOVE BOX LATCH - REMOVAL
........23-148
GLOVE BOX LATCH STRIKER -
INSTALLATION
......................23-149
GLOVE BOX LATCH STRIKER - REMOVAL
. 23-148GRAB HANDLE - INSTALLATION,
A-PILLAR TRIM.....................23-156
GRAB HANDLE - REMOVAL, A-PILLAR
TRIM.............................23-156
GRID - DESCRIPTION, REAR WINDOW
DEFOGGER..........................8G-5
GRID - DIAGNOSIS AND TESTING, REAR
WINDOW DEFOGGER..................8G-5
GRID - OPERATION, REAR WINDOW
DEFOGGER..........................8G-5
GRID REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING.................8G-4
GRILLE - INSTALLATION..............23-142
GRILLE - INSTALLATION, COWL........23-140
GRILLE - REMOVAL..................23-142
GRILLE - REMOVAL, COWL...........23-140
GRILLE OPENING REINFORCEMENT -
INSTALLATION......................23-142
GRILLE OPENING REINFORCEMENT -
REMOVAL.........................23-142
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO..............................8W-01-9
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-9
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-11
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION.................8A-10
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION.................8A-10
GROUNDS - DESCRIPTION, POWER......8E-13
GUARD - DESCRIPTION, THERMAL......8F-20
GUARD - INSTALLATION, THERMAL......8F-20
GUARD - OPERATION, THERMAL........8F-20
GUARD - REMOVAL, THERMAL..........8F-20
GUIDE ASSEMBLY - INSTALLATION.....23-179
GUIDE ASSEMBLY - REMOVAL.........23-179
GUIDE SEALS - DESCRIPTION, VALVE . 9-29,9-38
GUIDES - DESCRIPTION, VALVE......9-19,9-30
HALF SHAFT - CAUTION................3-10
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-10
HALF SHAFT - INSTALLATION............3-11
HALF SHAFT - REMOVAL...............3-10
HALF SHAFT, SPECIFICATIONS...........3-11
HANDLE - INSTALLATION, A-PILLAR
TRIM AND GRAB....................23-156
HANDLE - INSTALLATION, ASSIST......23-157
HANDLE - INSTALLATION, EXTERIOR . . . 23-123,
23-130,23-136
HANDLE - INSTALLATION, LATCH
RELEASE..........................23-120
HANDLE - REMOVAL, A-PILLAR TRIM
AND GRAB.........................23-156
HANDLE - REMOVAL, ASSIST..........23-157
HANDLE - REMOVAL, EXTERIOR . 23-123,23-130,
23-136
HANDLE - REMOVAL, LATCH RELEASE . . 23-120
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-7
HAZARD SWITCH - DESCRIPTION
.......8L-29
HAZARD SWITCH - INSTALLATION
.......8L-30
HAZARD SWITCH - OPERATION
.........8L-29
HAZARD SWITCH - REMOVAL
..........8L-30
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION
........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION
........................5-36
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION
..........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL
...........................5-36
HEAD - DESCRIPTION, CYLINDER
........9-30
HEAD COVER(S) - DESCRIPTION,
CYLINDER
...........................9-25
HEAD COVER(S) - INSTALLATION,
CYLINDER
.......................9-26,9-34
HEAD COVER(S) - REMOVAL, CYLINDER
. . 9-25,
9-34
KJINDEX 11
Description Group-Page Description Group-Page Description Group-Page

INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-68
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION........................9-26
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION....................9-28,9-36
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.......................9-27,9-35
INTERIOR - DESCRIPTION, LAMPS/
LIGHTING..........................8L-65
INTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING....................8L-68
INTERIOR - OPERATION, LAMPS/
LIGHTING..........................8L-67
INTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-71
INTERLOCK CABLE - INSTALLATION,
PARK .............................21-153
INTERLOCK CABLE - REMOVAL, PARK . . . 21-153
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT.........21-124
INTERLOCK SYSTEM - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION
SHIFT.............................21-125
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT.........21-125
INTERMEDIATE SHAFT - INSTALLATION . . . 19-11
INTERMEDIATE SHAFT - REMOVAL......19-11
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-4
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
INTRUSION TRANSCEIVER MODULE -
DESCRIPTION.......................8Q-14
INTRUSION TRANSCEIVER MODULE -
INSTALLATION......................8Q-16
INTRUSION TRANSCEIVER MODULE -
OPERATION.........................8Q-15
INTRUSION TRANSCEIVER MODULE -
REMOVAL..........................8Q-15
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - INSTALLATION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
IOD FUSE - REMOVAL..............8W-97-3
ISO FLARING - STANDARD PROCEDURE....5-8
JOINT - DESCRIPTION, UPPER
SUSPENSION ARM, BUSHINGS, AND
BALL...............................2-20
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - INSTALLATION, UPPER BALL.....2-20
JOINT - OPERATION, UPPER
SUSPENSION ARM, BUSHINGS, AND
BALL...............................2-20
JOINT - REMOVAL, UPPER BALL.........2-20
JOINT/BOOT-INNER - INSTALLATION, CV . . . 3-17
JOINT/BOOT-INNER - REMOVAL, CV.......3-15
JOINT/BOOT-OUTER - INSTALLATION, CV . . . 3-13
JOINT/BOOT-OUTER - REMOVAL, CV......3-12
JOINTS - ASSEMBLY, SINGLE CARDAN
UNIVERSAL...........................3-9
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL...................3-8
JOUNCE BUMPER - INSTALLATION.......2-19
JOUNCE BUMPER - REMOVAL...........2-19
JUMP STARTING PROCEDURE -
STANDARD PROCEDURE
.................0-5
JUNCTION BLOCK - DESCRIPTION
.....8W-97-4
JUNCTION BLOCK - DESCRIPTION
........5-20
JUNCTION BLOCK - DIAGNOSIS AND
TESTING
.........................8W-97-4
JUNCTION BLOCK - INSTALLATION
.......5-20
JUNCTION BLOCK - OPERATION
......8W-97-4
JUNCTION BLOCK - OPERATION
..........5-20
JUNCTION BLOCK - REMOVAL
...........5-20
KEY - DESCRIPTION, TRANSPONDER
....8Q-18
KEY - OPERATION, TRANSPONDER
......8Q-18
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY
................8E-15
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-18
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-16KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY............................8E-17
KEY TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY........8Q-8
KEY-IN IGNITION SWITCH -
DESCRIPTION.......................19-10
KEY-IN IGNITION SWITCH - DIAGNOSIS
AND TESTING.......................19-10
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE................8N-7
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE...............8N-7
KEYLESS ENTRY MODULE - OPERATION,
REMOTE............................8N-7
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE............................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
SPECIFICATIONS, REMOTE..............8N-9
KNEE BLOCKER - INSTALLATION.......23-155
KNEE BLOCKER - REMOVAL...........23-155
KNOCK SENSOR - DESCRIPTION.........8I-11
KNOCK SENSOR - INSTALLATION........8I-12
KNOCK SENSOR - OPERATION..........8I-11
KNOCK SENSOR - REMOVAL............8I-12
KNUCKLE - INSTALLATION...............2-9
KNUCKLE - REMOVAL...................2-9
LABEL - DESCRIPTION, VEHICLE
EMISSION CONTROL INFORMATION
(VECI)............................Intro.-8
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION.....................Intro.-9
LACE - INSTALLATION, OPENING TRIM . . 23-180
LACE - REMOVAL, OPENING TRIM......23-180
LAMP BULB - INSTALLATION, ASH
RECEIVER..........................8L-71
LAMP BULB - INSTALLATION, CARGO....8L-73
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP BULB - INSTALLATION,
COURTESY.........................8L-76
LAMP BULB - INSTALLATION, FRONT....8L-27
LAMP BULB - INSTALLATION, FRONT
FOG ...............................8L-22
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-28
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-45
LAMP BULB - INSTALLATION, READING . . . 8L-79
LAMP BULB - INSTALLATION, REAR.....8L-59
LAMP BULB - INSTALLATION, REPEATER . . 8L-60
LAMP BULB - INSTALLATION, VANITY....8L-84
LAMP BULB - REMOVAL, ASH RECEIVER . . 8L-71
LAMP BULB - REMOVAL, CARGO........8L-72
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-18
LAMP BULB - REMOVAL, COURTESY.....8L-75
LAMP BULB - REMOVAL, FRONT........8L-26
LAMP BULB - REMOVAL, FRONT FOG....8L-21
LAMP BULB - REMOVAL, FRONT
POSITION..........................8L-28
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-44
LAMP BULB - REMOVAL, READING......8L-79
LAMP BULB - REMOVAL, REAR.........8L-58
LAMP BULB - REMOVAL, REPEATER.....8L-60
LAMP BULB - REMOVAL, VANITY........8L-83
LAMP INDICATOR - DESCRIPTION,
FRONT FOG.........................8J-19
LAMP INDICATOR - DESCRIPTION, REAR
FOG ...............................8J-27
LAMP INDICATOR - OPERATION, FRONT
FOG ...............................8J-19
LAMP INDICATOR - OPERATION, REAR
FOG ...............................8J-27
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-24
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR
.............8J-24
LAMP RELAY - DESCRIPTION, DAYTIME
RUNNING
...........................8L-20
LAMP RELAY - DESCRIPTION, FRONT
FOG
...............................8L-22
LAMP RELAY - DESCRIPTION, PARK
.....8L-54
LAMP RELAY - DESCRIPTION, REAR FOG
. 8L-56LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT FOG.................8L-23
LAMP RELAY - DIAGNOSIS AND
TESTING, PARK......................8L-55
LAMP RELAY - DIAGNOSIS AND
TESTING, REAR FOG..................8L-57
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - INSTALLATION, FRONT
FOG ...............................8L-24
LAMP RELAY - INSTALLATION, PARK.....8L-56
LAMP RELAY - INSTALLATION, REAR
FOG ...............................8L-58
LAMP RELAY - OPERATION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - OPERATION, FRONT FOG . . 8L-22
LAMP RELAY - OPERATION, PARK.......8L-54
LAMP RELAY - OPERATION, REAR FOG . . . 8L-57
LAMP RELAY - REMOVAL, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - REMOVAL, FRONT FOG . . . 8L-24
LAMP RELAY - REMOVAL, PARK........8L-55
LAMP RELAY - REMOVAL, REAR FOG....8L-58
LAMP REPLACEMENT - STANDARD
PROCEDURE, CMTC...................8M-2
LAMP REPLACEMENT - STANDARD
PROCEDURE, COURTESY...............8M-2
LAMP SWITCH - DESCRIPTION, BACKUP . . 8L-15
LAMP SWITCH - DESCRIPTION, BRAKE . . . 8L-16
LAMP SWITCH - DIAGNOSIS AND
TESTING, BACKUP.....................8L-15
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE.....................8L-17
LAMP SWITCH - INSTALLATION, BRAKE . . 8L-18
LAMP SWITCH - INSTALLATION, CARGO . . 8L-74
LAMP SWITCH - INSTALLATION,
READING...........................8L-80
LAMP SWITCH - OPERATION, BACKUP . . . 8L-15
LAMP SWITCH - OPERATION, BRAKE.....8L-16
LAMP SWITCH - REMOVAL, BRAKE......8L-17
LAMP SWITCH - REMOVAL, CARGO......8L-73
LAMP SWITCH - REMOVAL, READING....8L-80
LAMP UNIT - ADJUSTMENT, FRONT FOG . . 8L-25
LAMP UNIT - INSTALLATION, ASH
RECEIVER..........................8L-72
LAMP UNIT - INSTALLATION, CARGO.....8L-74
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP UNIT - INSTALLATION, COURTESY . . 8L-77
LAMP UNIT - INSTALLATION, FRONT.....8L-28
LAMP UNIT - INSTALLATION, FRONT
FOG ...............................8L-25
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-46
LAMP UNIT - INSTALLATION, READING . . . 8L-81
LAMP UNIT - INSTALLATION, REAR......8L-60
LAMP UNIT - INSTALLATION, REPEATER . . 8L-61
LAMP UNIT - REMOVAL, ASH RECEIVER . . 8L-72
LAMP UNIT - REMOVAL, CARGO........8L-74
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-19
LAMP UNIT - REMOVAL, COURTESY.....8L-76
LAMP UNIT - REMOVAL, FRONT.........8L-27
LAMP UNIT - REMOVAL, FRONT FOG.....8L-25
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-45
LAMP UNIT - REMOVAL, READING.......8L-81
LAMP UNIT - REMOVAL, REAR..........8L-59
LAMP UNIT - REMOVAL, REPEATER......8L-60
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
DIAGNOSIS AND TESTING..............8L-7
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-5
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS.....................8L-15
LAMPS/LIGHTING - INTERIOR -
DESCRIPTION.......................8L-65
LAMPS/LIGHTING - INTERIOR -
DIAGNOSIS AND TESTING.............8L-68
LAMPS/LIGHTING - INTERIOR -
OPERATION
.........................8L-67
LAMPS/LIGHTING - INTERIOR -
SPECIFICATIONS
.....................8L-71
LASH ADJUSTER - DIAGNOSIS AND
TESTING, HYDRAULIC
..............9-19,9-30
LATCH - ACCESS PANEL - DESCRIPTION
. 23-139
LATCH - ACCESS PANEL - INSTALLATION
. 23-139
14 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

LATCH - ACCESS PANEL - REMOVAL....23-139
LATCH - INSTALLATION . . 23-120,23-124,23-131,
23-137
LATCH - INSTALLATION, FLIP-UP GLASS . 23-136
LATCH - INSTALLATION, FLOOR
CONSOLE LID......................23-158
LATCH - INSTALLATION, GLOVE BOX....23-148
LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT BACK...........23-170
LATCH / LOCK - REMOVAL, FOLDING
REAR SEAT BACK...................23-170
LATCH - REMOVAL......23-120,23-124,23-131,
23-137
LATCH - REMOVAL, FLIP-UP GLASS.....23-136
LATCH - REMOVAL, FLOOR CONSOLE
LID...............................23-158
LATCH - REMOVAL, GLOVE BOX........23-148
LATCH RELEASE CABLE - INSTALLATION . 23-120
LATCH RELEASE CABLE - REMOVAL....23-120
LATCH RELEASE HANDLE -
INSTALLATION......................23-120
LATCH RELEASE HANDLE - REMOVAL . . . 23-120
LATCH STRIKER - INSTALLATION......23-124,
23-132,23-137
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-149
LATCH STRIKER - INSTALLATION, REAR
SEAT BACK........................23-171
LATCH STRIKER - REMOVAL....23-124,23-132,
23-137
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-148
LATCH STRIKER - REMOVAL, REAR
SEAT BACK........................23-170
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID...........21-80
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL..........................9-60
LEAK DETECTION PUMP - DESCRIPTION . . 25-27
LEAK DETECTION PUMP - INSTALLATION . 25-28
LEAK DETECTION PUMP - OPERATION....25-28
LEAK DETECTION PUMP - REMOVAL.....25-28
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-3
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE.......9-8
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-4
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-68
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-61
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-8
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-21
LEFT POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
LEFT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
LEFT POWER SEAT SWITCH -
INSTALLATION......................8N-18
LEFT POWER SEAT SWITCH -
OPERATION
.........................8N-17
LEFT POWER SEAT SWITCH - REMOVAL
. . 8N-18
LEFT SIDE - INSTALLATION
.........2-12,2-15
LEFT SIDE - REMOVAL
.............2-11,2-15
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID
........21-125
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-54
LEVEL - STANDARD PROCEDURES,
MASTER CYLINDER FLUID
..............5-26
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
.................21-126
LEVEL SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL
.......................14-9
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
...................14-9
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
.................14-10
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
.....................14-9
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-9LEVEL SWITCH - DESCRIPTION,
WASHER FLUID.....................8R-17
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-18
LEVEL SWITCH - OPERATION, WASHER
FLUID.............................8R-17
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-17
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP.........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LEVER - INSTALLATION................5-31
LEVER - INSTALLATION, SHIFT . . . 21-214,21-249
LEVER - REMOVAL....................5-31
LEVER - REMOVAL, SHIFT......21-213,21-248
LHD - INSTALLATION...............8W-97-6
LHD - REMOVAL....................8W-97-5
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LID LATCH - INSTALLATION, FLOOR
CONSOLE..........................23-158
LID LATCH - REMOVAL, FLOOR
CONSOLE..........................23-158
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITS - DESCRIPTION, HIGH AND LOW . . 25-20
LINE - DESCRIPTION, REFRIGERANT.....24-38
LINE - INSTALLATION, A/C DISCHARGE . . . 24-47
LINE - INSTALLATION, A/C LIQUID.......24-47
LINE - INSTALLATION, A/C SUCTION.....24-49
LINE - REMOVAL, A/C DISCHARGE.......24-46
LINE - REMOVAL, A/C LIQUID...........24-47
LINE - REMOVAL, A/C SUCTION.........24-48
LINE AND HOSES - DIAGNOSIS AND
TESTING, BRAKE.......................5-8
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-144
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-144
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-144
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-144
LINES - DESCRIPTION, BRAKE............5-8
LINES - DESCRIPTION, FUEL...........14-10
LINES - DESCRIPTION, VACUUM........25-33
LINK - INSTALLATION, STABILIZER.......2-14
LINK - REMOVAL, STABILIZER...........2-14
LINK CONNECTOR - DESCRIPTION, DATA . 8E-10
LINK CONNECTOR - OPERATION, DATA . . . 8E-10
LINKAGE - INSTALLATION................6-9
LINKAGE - REMOVAL...................6-8
LINKAGE - STANDARD PROCEDURE,
STEERING..........................19-16
LIQUID LINE - INSTALLATION, A/C.......24-47
LIQUID LINE - REMOVAL, A/C...........24-47
LOAD TEST - STANDARD PROCEDURE....8F-12
LOAD VALUE - DESCRIPTION
...........25-20
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-4
LOCATIONS - SPECIFICATIONS, SEALER
. . 23-87LOCATIONS - SPECIFICATIONS, WELD
AND STRUCTURAL ADHESIVE...........23-9
LOCK - INSTALLATION, FOLDING REAR
SEAT BACK LATCH..................23-170
LOCK - REMOVAL, FOLDING REAR SEAT
BACK LATCH.......................23-170
LOCK / UNLOCK SWITCH -
INSTALLATION, DOOR.................8N-5
LOCK / UNLOCK SWITCH - REMOVAL,
DOOR..............................8N-4
LOCK CYLINDER - INSTALLATION......23-125,
23-138
LOCK CYLINDER - INSTALLATION.......19-11
LOCK CYLINDER - REMOVAL....23-125,23-137
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK OUT - ADJUSTMENT..............5-30
LOCK RELAY - DESCRIPTION, DOOR......8N-6
LOCK RELAY - DIAGNOSIS AND
TESTING, DOOR......................8N-6
LOCK RELAY - INSTALLATION, DOOR.....8N-7
LOCK RELAY - OPERATION, DOOR........8N-6
LOCK RELAY - REMOVAL, DOOR.........8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8Q-9
LOCK SWITCH - DESCRIPTION,
TAILGATE CYLINDER...................8N-9
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8Q-10
LOCK SWITCH - DIAGNOSIS AND
TESTING, TAILGATE CYLINDER..........8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - INSTALLATION,
TAILGATE CYLINDER..................8N-10
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - OPERATION, TAILGATE
CYLINDER...........................8N-9
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - REMOVAL, TAILGATE
CYLINDER..........................8N-10
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-3
LOCK/UNLOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-4
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-38
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-37
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP
.........................8L-40
LOW FUEL INDICATOR - DESCRIPTION
. . . 8J-22
LOW FUEL INDICATOR - OPERATION
.....8J-22
LOW INDICATOR - DESCRIPTION,
COOLANT
...........................8J-15
LOW INDICATOR - OPERATION,
COOLANT
...........................8J-16
LOW LIMITS - DESCRIPTION, HIGH
......25-20
LOW MODE INDICATOR - DESCRIPTION,
FOUR
..............................8J-29
LOW MODE INDICATOR - OPERATION,
FOUR
..............................8J-30
LOW OIL PRESSURE INDICATOR -
DESCRIPTION
.......................8J-23
LOW OIL PRESSURE INDICATOR -
OPERATION
.........................8J-23
LOW PRESSURE SWITCH -
DESCRIPTION, A/C
...................24-18
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C
...................24-19
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-19
KJINDEX 15
Description Group-Page Description Group-Page Description Group-Page

SENSOR - INSTALLATION, OXYGEN......14-43
SENSOR - INSTALLATION, POSITION....21-210,
21-247
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-35
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-48
SENSOR - OPERATION, AMBIENT TEMP . . . 8M-9
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-24
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-31
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-20
SENSOR - OPERATION, FRONT IMPACT . . . 8O-21
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - OPERATION, INPUT SPEED . . . 21-143
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - OPERATION, KNOCK..........8I-11
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-144
SENSOR - OPERATION, MAP...........14-38
SENSOR - OPERATION, OUTPUT SPEED . . 21-152
SENSOR - OPERATION, OXYGEN........14-40
SENSOR - OPERATION, POSITION......21-209,
21-247
SENSOR - OPERATION, THROTTLE
POSITION..........................14-47
SENSOR - OPERATION, TRANSMISSION
RANGE............................21-168
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE.....................21-170
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-24
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-31
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-20
SENSOR - REMOVAL, FRONT IMPACT....8O-22
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-34
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - REMOVAL, INPUT SPEED.....21-143
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE......................14-37
SENSOR - REMOVAL, KNOCK...........8I-12
SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-144
SENSOR - REMOVAL, MAP.............14-39
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-152
SENSOR - REMOVAL, OXYGEN..........14-41
SENSOR - REMOVAL, POSITION . . 21-210,21-247
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-35
SENSOR - REMOVAL, THROTTLE
POSITION..........................14-47
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE.......8M-9
SENSOR RETURN - DESCRIPTION.......8E-14
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-65
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE
..........................9-65
SENSOR/SWITCH - OPERATION, OIL
PRESSURE
..........................9-65
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE
..........................9-65
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION
.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION
.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
OPERATION
.........................8E-16
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL
..........................8E-17
SENTRY KEY TRANSPONDER
PROGRAMMING - STANDARD
PROCEDURE
.........................8Q-8
SERPENTINE DRIVE BELT - DIAGNOSIS
AND TESTING
........................7-15
SERVO - DESCRIPTION
.................8P-4
SERVO - INSTALLATION
................8P-5
SERVO - OPERATION
..................8P-4
SERVO - REMOVAL
....................8P-4SETTING TRANSMITTER CODES -
STANDARD PROCEDURE...............8M-9
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-9
SHAFT - CAUTION, HALF................3-10
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-10
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - FRONT - INSTALLATION,
PROPELLER...........................3-6
SHAFT - FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT - INSTALLATION, BALANCE........9-74
SHAFT - INSTALLATION, HALF...........3-11
SHAFT - INSTALLATION, IDLER..........9-77
SHAFT - INSTALLATION, INTERMEDIATE . . 19-11
SHAFT - REAR - INSTALLATION,
PROPELLER...........................3-7
SHAFT - REAR - REMOVAL, PROPELLER....3-7
SHAFT - REMOVAL, BALANCE...........9-74
SHAFT - REMOVAL, HALF...............3-10
SHAFT - REMOVAL, IDLER..............9-77
SHAFT - REMOVAL, INTERMEDIATE......19-11
SHAFT ANGLE - STANDARD
PROCEDURES, PROPELLER..............3-3
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT.....................21-208,21-246
SHAFT SEAL - INSTALLATION, REAR
OUTPUT............................21-212
SHAFT SEAL - REMOVAL, FRONT
OUTPUT.....................21-208,21-246
SHAFT SEAL - REMOVAL, REAR OUTPUT . 21-210
SHAFT SEALS - INSTALLATION, AXLE....3-102,
3-38
SHAFT SEALS - REMOVAL, AXLE....3-101,3-37
SHAFT, SPECIFICATIONS - HALF..........3-11
SHAFT, SPECIFICATIONS - PROPELLER.....3-6
SHAFTS - INSTALLATION, AXLE . 3-101,3-37,3-65
SHAFTS - REMOVAL, AXLE.....3-101,3-37,3-65
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH...............23-143
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH...............23-144
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH...............23-143
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH...............23-144
SHIELDS - DESCRIPTION, HEAT..........11-4
SHIELDS - INSTALLATION, SEAT
CUSHION SIDE.....................23-167
SHIELDS - REMOVAL, SEAT CUSHION
SIDE.............................23-167
SHIFT BEZEL - INSTALLATION.........23-158
SHIFT BEZEL - REMOVAL.............23-158
SHIFT BOOT - INSTALLATION, 4WD
FLOOR............................23-156
SHIFT BOOT - REMOVAL, 4WD FLOOR . . . 23-156
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-124
SHIFT INTERLOCK SYSTEM - DIAGNOSIS
AND TESTING, BRAKE TRANSMISSION . . 21-125
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-125
SHIFT LEVER - INSTALLATION . . . 21-214,21-249
SHIFT LEVER - REMOVAL.......21-213,21-248
SHIFT MECHANISM - DESCRIPTION.....21-160
SHIFT MECHANISM - INSTALLATION....21-160
SHIFT MECHANISM - OPERATION
......21-160
SHIFT MECHANISM - REMOVAL
........21-160
SHOCK - INSTALLATION
................2-18
SHOCK - REMOVAL
....................2-18
SHOES - INSTALLATION, DRUM BRAKE
....5-11
SHOES - REMOVAL, DRUM BRAKE
.......5-11
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
...........................8W-01-9
SIDE - INSTALLATION, LEFT
.........2-12,2-15
SIDE - INSTALLATION, RIGHT
........2-12,2-15
SIDE - REMOVAL, LEFT
.............2-11,2-15
SIDE - REMOVAL, RIGHT
...........2-11,2-14
SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL PASSENGER
......23-154SIDE BEZEL - REMOVAL, INSTRUMENT
PANEL PASSENGER..................23-154
SIDE BEZELS - INSTALLATION,
INSTRUMENT PANEL DRIVER..........23-154
SIDE BEZELS - REMOVAL, INSTRUMENT
PANEL DRIVER.....................23-153
SIDE CURTAIN AIRBAG - DESCRIPTION . . . 8O-38
SIDE CURTAIN AIRBAG - INSTALLATION . . 8O-41
SIDE CURTAIN AIRBAG - OPERATION....8O-39
SIDE CURTAIN AIRBAG - REMOVAL......8O-40
SIDE IMPACT AIRBAG CONTROL
MODULE - DESCRIPTION..............8O-43
SIDE IMPACT AIRBAG CONTROL
MODULE - INSTALLATION.............8O-45
SIDE IMPACT AIRBAG CONTROL
MODULE - OPERATION................8O-43
SIDE IMPACT AIRBAG CONTROL
MODULE - REMOVAL.................8O-44
SIDE MOLDINGS - INSTALLATION, BODY . 23-140
SIDE MOLDINGS - REMOVAL, BODY....23-140
SIDE RAIL WEATHERSTRIP/RETAINER -
INSTALLATION......................23-186
SIDE RAIL WEATHERSTRIP/RETAINER -
REMOVAL.........................23-186
SIDE SHIELDS - INSTALLATION, SEAT
CUSHION..........................23-167
SIDE SHIELDS - REMOVAL, SEAT
CUSHION..........................23-167
SIDE VIEW MIRROR - INSTALLATION....23-145
SIDE VIEW MIRROR - REMOVAL.......23-145
SIDEVIEW MIRROR - REMOVAL..........8N-13
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-34
SIGNAL INDICATOR - OPERATION, TURN . . 8J-34
SILL SCUFF PLATE - INSTALLATION,
DOOR............................23-157
SILL SCUFF PLATE - REMOVAL, DOOR . . . 23-157
SINGLE CARDAN UNIVERSAL JOINTS -
ASSEMBLY...........................3-9
SINGLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY.........................3-8
SIREN - DESCRIPTION................8Q-16
SIREN - INSTALLATION...............8Q-17
SIREN - OPERATION..................8Q-17
SIREN - REMOVAL...................8Q-17
SKID PLATE - INSTALLATION, FRONT......13-6
SKID PLATE - INSTALLATION, FUEL
TANK ...............................13-9
SKID PLATE - INSTALLATION, TRANSFER
CASE...............................13-7
SKID PLATE - REMOVAL, FRONT.........13-6
SKID PLATE - REMOVAL, FUEL TANK......13-9
SKID PLATE - REMOVAL, TRANSFER
CASE...............................13-7
SKIS INDICATOR - DESCRIPTION........8J-31
SKIS INDICATOR - OPERATION..........8J-31
SKIS INITIALIZATION - STANDARD
PROCEDURE.........................8Q-8
SLEEVE - INSTALLATION, HEADREST....23-164
SLEEVE - REMOVAL, HEADREST.......23-164
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-27
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-27
SOLENOID - OPERATION, EVAP/PURGE . . . 25-27
SOLENOID - REMOVAL, EVAP/PURGE.....25-27
SOLENOID SWITCH VALVE -
DESCRIPTION......................21-161
SOLENOID SWITCH VALVE - OPERATION . 21-161
SOLENOIDS - DESCRIPTION...........21-161
SOLENOIDS - OPERATION.............21-162
SOLENOID/TRS ASSEMBLY -
DESCRIPTION, TRANSMISSION........21-169
SOLENOID/TRS ASSEMBLY -
INSTALLATION, TRANSMISSION........21-170
SOLENOID/TRS ASSEMBLY -
OPERATION, TRANSMISSION..........21-169
SOLENOID/TRS ASSEMBLY - REMOVAL,
TRANSMISSION.....................21-170
SPACER - INSTALLATION, COLLAPSIBLE . . . 3-70
SPACER - REMOVAL, COLLAPSIBLE.......3-70
SPARE TIRE - INSTALLATION............22-9
SPARE TIRE - REMOVAL
................22-8
SPARE TIRE &TEMPORARY -
DESCRIPTION
........................22-6
SPARK PLUG - CLEANING SPARK
PLUGS
.............................8I-15
SPARK PLUG - DESCRIPTION
...........8I-12
SPARK PLUG - INSTALLATION
...........8I-15
24 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page

TANK - REMOVAL, FUEL...............14-25
TANK CHECK VALVE - DESCRIPTION,
FUEL..............................14-28
TANK CHECK VALVE - INSTALLATION,
FUEL..............................14-28
TANK CHECK VALVE - OPERATION, FUEL . . 14-28
TANK CHECK VALVE - REMOVAL, FUEL . . . 14-28
TANK SKID PLATE - INSTALLATION,
FUEL...............................13-9
TANK SKID PLATE - REMOVAL, FUEL......13-9
TASK MANAGER - DESCRIPTION........25-17
TASK MANAGER - OPERATION..........25-21
TCM QUICK LEARN - STANDARD
PROCEDURE........................8E-21
TEMP INDICATOR - DESCRIPTION,
TRANS.............................8J-33
TEMP INDICATOR - OPERATION, TRANS . . 8J-34
TEMP SENSOR - DESCRIPTION,
AMBIENT...........................8M-9
TEMP SENSOR - OPERATION, AMBIENT . . . 8M-9
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE............................8J-18
TEMPERATURE GAUGE - OPERATION,
ENGINE............................8J-18
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-24
TEMPERATURE SENSOR - DESCRIPTION,
ENGINE COOLANT.....................7-19
TEMPERATURE SENSOR - DESCRIPTION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION.....................21-170
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT...............8M-9
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-24
TEMPERATURE SENSOR -
INSTALLATION, ENGINE COOLANT........7-21
TEMPERATURE SENSOR -
INSTALLATION, INTAKE AIR............14-38
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-24
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-20
TEMPERATURE SENSOR - OPERATION,
INTAKE AIR .........................14-36
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION.....................21-170
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-24
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-20
TEMPERATURE SENSOR - REMOVAL,
INTAKE AIR .........................14-37
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT.....8M-9
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-36
TENSIONER - OPERATION, SEAT BELT....8O-36
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN................14-3
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE....................14-16
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY.....................14-15
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE....................14-15
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE...............21-79
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-2
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-10
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-11
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-14
TEST - STANDARD PROCEDURE, LOAD . . . 8F-12
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE
...............8F-12
TEST - STANDARD PROCEDURE,
VERIFICATION
........................8O-8
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION
..........................25-2
TEST MODE - DESCRIPTION, STATE
DISPLAY
............................25-2
TESTER - STANDARD PROCEDURE,
USING MIDTRONICS ELECTRICAL
.......8F-15TETHER ANCHOR - DESCRIPTION, CHILD . 8O-13
TETHER ANCHOR - OPERATION, CHILD . . . 8O-13
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-3
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-6
THERMAL GUARD - DESCRIPTION.......8F-20
THERMAL GUARD - INSTALLATION......8F-20
THERMAL GUARD - OPERATION.........8F-20
THERMAL GUARD - REMOVAL..........8F-20
THERMOSTAT - DIAGNOSIS AND
TESTING............................7-21
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-21
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM..............21-81
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-4
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN............9-9
THROTTLE BODY - DESCRIPTION........14-43
THROTTLE BODY - INSTALLATION.......14-44
THROTTLE BODY - OPERATION.........14-43
THROTTLE BODY - REMOVAL...........14-43
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-46
THROTTLE CONTROL CABLE - REMOVAL . . 14-45
THROTTLE POSITION SENSOR -
DESCRIPTION.........................14-47
THROTTLE POSITION SENSOR -
INSTALLATION.......................14-48
THROTTLE POSITION SENSOR -
OPERATION.........................14-47
THROTTLE POSITION SENSOR -
REMOVAL..........................14-47
TIE ROD END - INSTALLATION..........19-16
TIE ROD END - REMOVAL..............19-16
TIE ROD END REMOVAL TOOL, SPECIAL
TOOLS - OUTER.....................19-15
TIME INDICATOR - DESCRIPTION, FULL . . . 8J-29
TIME INDICATOR - DESCRIPTION, PART . . 8J-29
TIME INDICATOR - OPERATION, FULL....8J-30
TIME INDICATOR - OPERATION, PART....8J-29
TIMING - DESCRIPTION, VALVE..........9-71
TIMING - OPERATION, VALVE............9-71
TIMING - SPECIFICATIONS, IGNITION......8I-2
TIMING BELT / CHAIN COVER(S) -
INSTALLATION........................9-76
TIMING BELT / CHAIN COVER(S) -
REMOVAL...........................9-74
TIMING CHAIN WEAR, STANDARD
PROCEDURE - MEASURING.............9-71
TIRE - INSTALLATION, SPARE...........22-9
TIRE - REMOVAL, SPARE...............22-8
TIRE INFLATION - DIAGNOSIS AND
TESTING............................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-8
TIRE ROTATION - STANDARD
PROCEDURE.........................22-2
TIRE &TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING........................22-8
TIRES - DESCRIPTION.................22-6
TIRES - DESCRIPTION, RADIAL-PLY.......22-6
TIRES - DESCRIPTION, REPLACEMENT....22-7
TIRES AND WHEEL RUNOUT -
DIAGNOSIS AND TESTING..............22-1
TO GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT.............8W-01-9
TO GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT . . 8W-01-9
TO USE WIRING DIAGRAMS -
DESCRIPTION, HOW................8W-01-1
TOE ADJUSTMENT - STANDARD
PROCEDURE..........................2-5
TOE ADJUSTMENT - STANDARD
PROCEDURE, CAMBER, CASTER..........2-5
TOOL, SPECIAL TOOLS - OUTER TIE
ROD END REMOVAL..................19-15
TOOLS - 3.7L ENGINE, SPECIAL
..........9-15
TOOLS - 8 1/4 AXLE, SPECIAL
...........3-98
TOOLS - BASE BRAKES, SPECIAL
.........5-7
TOOLS - BODY, SPECIAL
................23-5
TOOLS - COOLING, SPECIAL
.............7-14TOOLS - FRONT AXLE, SPECIAL..........3-34
TOOLS - FRONT SUSPENSION, SPECIAL....2-8
TOOLS - FUEL SYSTEM, SPECIAL........14-6
TOOLS - OUTER TIE ROD END REMOVAL
TOOL, SPECIAL......................19-15
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-20
TOOLS - REAR AXLE, SPECIAL...........3-63
TOOLS - RFE TRANSMISSION, SPECIAL . . 21-120
TOOLS - STEERING COLUMN, SPECIAL....19-8
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-10
TOOLS, BATTERY SYSTEM - SPECIAL.....8F-7
TOOLS, SPECIFICATIONS - SPECIAL....3-12,3-6
TOOLS, SPECIFICATIONS - SPECIAL......8F-24
TOP COVER - INSTALLATION,
INSTRUMENT PANEL.................23-153
TOP COVER - REMOVAL, INSTRUMENT
PANEL............................23-152
TORQUE - SPECIFICATIONS.............13-6
TORQUE CHART, SPECIFICATIONS . . 19-15,19-19,
19-8
TORQUE CHART, SPECIFICATIONS.....2-17,2-8
TORQUE CONVERTER - DESCRIPTION . . . 21-162
TORQUE CONVERTER - INSTALLATION . . . 21-167
TORQUE CONVERTER - OPERATION.....21-166
TORQUE CONVERTER - REMOVAL......21-167
TORQUE, EXCEPT DIESEL..............8F-23
TORQUE, GAS POWERED..............8F-38
TORQUE, IGNITION SYSTEM.............8I-3
TORQUE REFERENCES - DESCRIPTION . . Intro.-7
TORQUE, SPECIFICATIONS...............5-7
TORQUE, SPECIFICATIONS..............7-13
TORQUE, SPECIFICATIONS.............25-26
TORQUE, SPECIFICATIONS..............9-12
TORQUE, SPECIFICATIONS..............14-5
TORQUE, SPEED CONTROL.............8P-2
TOUCH-UP - DESCRIPTION, PAINT......23-163
TOW CONNECTOR - INSTALLATION,
TRAILER...........................8L-61
TOW CONNECTOR - REMOVAL, TRAILER . . 8L-61
TOW HOOK - INSTALLATION, FRONT......13-8
TOW HOOK - INSTALLATION, REAR.......13-8
TOW HOOK - REMOVAL, FRONT..........13-8
TOW HOOK - REMOVAL, REAR...........13-8
TOW RELAY - DESCRIPTION, TRAILER....8L-61
TOW RELAY - DIAGNOSIS AND TESTING,
TRAILER...........................8L-62
TOW RELAY - INSTALLATION, TRAILER . . . 8L-64
TOW RELAY - OPERATION, TRAILER.....8L-62
TOW RELAY - REMOVAL, TRAILER.......8L-63
TOW WIRING - DESCRIPTION, TRAILER . . 8L-64
TOWING - STANDARD PROCEDURE........0-6
TRACK - DESCRIPTION, SEAT..........8N-15
TRACK - DIAGNOSIS AND TESTING,
SEAT ..............................8N-16
TRACK - INSTALLATION, SEAT.........23-168
TRACK - INSTALLATION, SEAT..........8N-16
TRACK - OPERATION, SEAT............8N-15
TRACK - REMOVAL, SEAT.............23-168
TRACK - REMOVAL, SEAT..............8N-16
TRAC-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-109,
3-77
TRAC-LOK - CLEANING, DIFFERENTIAL . . . 3-109,
3-77
TRAC-LOK - DISASSEMBLY,
DIFFERENTIAL...................3-107,3-75
TRAC-LOK - INSPECTION, DIFFERENTIAL . 3-109,
3-77
TRAC-LOKT- DIAGNOSIS AND TESTING . . 3-106,
3-74
TRAILER HITCH - INSTALLATION.........13-9
TRAILER HITCH - REMOVAL.............13-9
TRAILER TOW CONNECTOR -
INSTALLATION.......................8L-61
TRAILER TOW CONNECTOR - REMOVAL . . 8L-61
TRAILER TOW RELAY - DESCRIPTION....8L-61
TRAILER TOW RELAY - DIAGNOSIS AND
TESTING...........................8L-62
TRAILER TOW RELAY - INSTALLATION . . . 8L-64
TRAILER TOW RELAY - OPERATION......8L-62
TRAILER TOW RELAY - REMOVAL
.......8L-63
TRAILER TOW WIRING - DESCRIPTION
. . . 8L-64
TRANS COOLER - DESCRIPTION
.........7-32
TRANS TEMP INDICATOR -
DESCRIPTION
.......................8J-33
TRANS TEMP INDICATOR - OPERATION
. . . 8J-34
KJINDEX 27
Description Group-Page Description Group-Page Description Group-Page