2002 ISUZU AXIOM ignition

9J1±11
RESTRAINT CONTROL SYSTEM
Chart C ªAIR BAGº Warning Lamp Does Not Comes ªONº Steady
StepActionYe sNo
11. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Ignition switch ªOFF.º
3. Remove and inspect ªMA01º meter fuse to the ªAIR BAGº
warning lamp.
Is fuse good?
Go to Step 2 Go to Step 7
21. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag assemblies.
Yellow 2±pin connectors located at base of steering column
and behind the glove box assembly.
3. Disconnect SDM.
4. Ignition switch ªON.º
5. Measure voltage on SDM harness connector from terminal ª7º
to terminal ª6º (ground).
Is system voltage present on terminal ª7º?
Go to Step 4 Go to Step 3
31. Ignition switch ªOFF.º
2. Remove instrument meter cluster.
3. Check for proper connection to instrument cluster at
IB04±GRN terminal.
4. If OK, then remove and inspect ªAIR BAGº bulb.
Is bulb good?
Go to Step 5
Replace bulb.
Go to
Step 6
41. Ignition switch ªOFF.º
2. Disconnect instrument meter cluster harness connector.
3. Ignition switch ªON.º
4. Measure voltage on SDM harness connector from terminal ª7º
to terminal ª6º (ground).
Is voltage 1 volt or less?
Go to Chart A.
Replace SRS
harness.
Go to
Step 6
51. Install bulb.
2. Measure resistance from instrument meter cluster harness
connector IB04±GRN terminal to SDM harness connector
terminal ª7º.
Is resistance 5.0 ohms or less?
Service
instrument meter
cluster.
Go to
Step 6
Replace SRS
harness.
Go to
Step 6
6Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished?Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 6
7Were you sent here from chart C?Go to Step 8 Go to Step 1
81. Replace ªMA01º meter fuse.
2. Ignition switch ªONº wait 10 seconds then ignition switch
ªOFF.º
3. Remove and inspect ªMA01º meter fuse.
Is fuse good?
Install ªMA01º
meter fuse.
Go to
Step 10 Go to Step 9

RESTRAINT CONTROL SYSTEM 9J1±12
Chart C ªAIR BAGº Warning Lamp Does Not Comes ªONº Steady (Cont'd)
StepNo Ye s Action
91. Disconnect SRS coil and passenger air bag assemblies.
Yellow 2±pin connectors located at base of steering column
and behind the glove box assembly.
2. Disconnect SDM.
3. Replace ªMA01º meter fuse.
4. Ignition switch ªONº wait to 10 seconds.
5. Ignition switch ªOFFº.
6. Remove and inspection ªMA01º meter fuse.
Is fuse good?
Install ªMA01º
meter fuse.
Go to
Chart A .
Replace SRS
harness.
ReplaceªMA01º
meter fuse.
Go to
Step 10
10Reconnect all SRS components, ensure all components are
properly mounted.
Was this step finished?Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 10

9J1±13
RESTRAINT CONTROL SYSTEM
DTC 15 Passenger Deployment Loop Resistance High
D09R200001
Circuit Description:
When the ignition switch is turned ªONº, the SDM will
perform tests to diagnose critical malfunctions within
itself. Upon passing these tests ªignition 1º, and
deployment loop voltages are measured to ensure they
are within their respective normal voltage ranges. The
SDM then proceeds with the ªResistance Measurement
Testº. ªPassenger Bag Lowº terminal ª16º is grounded
through a resister and the passenger current source
connected to ªPassenger Bag Highº terminal ª15º allows a
known amount of current to flow. By monitoring the
voltage difference between ªPassenger Bag Highº and
ªPassenger Bag Lowº the SDM calculates the combined
resistance of the passenger air bag assembly, harness
wiring CKTs IB07±YEL/GRN and IB08±YEL/RED
connector terminal contact.
DTC Will Set When:
The combined resistance of the passenger air bag
assembly, harness wiring CKTs IB07±YEL/GRN and
IB08±YEL/RED, and connector terminal contact is above
a specified value. This test is run once each ignition cycle
during the ªResistance Measurement Testº when:
1. No ªhigher priority faultsº are detected during
ªTurn±ON.º
2. ªIgnition 1º voltage is in the specified value.
Action Taken:
SDM turns ªONº the ªAIR BAGº warning lamp and sets a
diagnostic trouble code.
DTC Will Clear When:
The ignition switch is turned ªOFF.º

RESTRAINT CONTROL SYSTEM 9J1±14
DTC Chart Test Description:
Number(s) below refer to step number(s) on the
diagnostic chart:
2. This test determines whether the malfunction is in
the SDM.
3. This test verifies proper connection of the yellow
2±pin connector.
4. This test checks for proper contact and/or corrosion
of the yellow 2±pin connector terminals.
5. The test checks for a malfunctioning passenger air
bag assembly.
6. This test determines whether the malfunction is due
to high resistance in the wiring.
Diagnostic Aids:
An intermittent condition is likely to be caused by a poor
connection at the passenger air bag assembly harness
connector terminals ª1º and ª2º, SDM terminal ª15º and
ª16º, or a poor wire to terminal connection in CKTs
IB07±YEL/GRN and IB08±YEL/RED. This test for this
diagnostic trouble code is only run while the ªAIR BAGº
warning lamp is performing the bulb check, unless DTC
17 or DTC 26 is detected. When a scan tool ªClear
Codesº command is issued and the malfunction is still
present, the DTC will not reappear until the next ignition
cycle.

9J1±15
RESTRAINT CONTROL SYSTEM
DTC 15 Passenger Deployment Loop Resistance High
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Use scan tool data list function, read and record the passenger
deployment loop resistance.
Is passenger resist more than 2.9 ohms?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Make sure the passenger air bag assembly yellow 2±pin
connector located behind the glove box assembly is seated
properly.
Is the yellow 2±pin connector connected properly?
Go to Step 4
Seat passenger
air bag assembly
yellow 2±pin
connector
properly.
Go to
Step 7
41. Disconnect and inspect the passenger air bag assembly
yellow 2±pin connector located behind the glove box
assembly.
2. If OK, reconnect the passenger air bag assembly 2±pin
connector.
3. Ignition switch ªON.º
Is DTC 15 current?
Go to Step 5
Ignition switch
ªOFF.º
Go to
Step 7
51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag 2±pin connectors
located at the base of the steering column and behind the
glove box assembly.
3. Connect J±41433 SRS driver / passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 15 current?
Go to Step 6
Ignition switch
ªOFF.º
Replace the
passenger air
bag assembly.
Go to
Step 7
61. Ignition switch ªOFF.º
2. There has been an increase in the total circuit resistance of the
passenger inflator deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB07±YEL/GRN and IB08±YEL/RED, and
SDM connector terminal ª15º and ª16º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 7 Go to Chart A .
71. Reconnect all components ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 7

RESTRAINT CONTROL SYSTEM 9J1±16
DTC 16 Passenger Deployment Loop Resistance Low
D09R200001
Circuit Description:
When the ignition switch is turned ªONº, the SDM will
perform tests to diagnose critical malfunctions within
itself. Upon passing these tests ªignition 1º, and
deployment loop voltages are measured to ensure they
are within their respective normal voltage ranges. The
SDM then proceeds with the ªResistance Measurement
Testº. ªPassenger Bag Lowº terminal ª16º is grounded
through a resistor and the passenger current source
connected to ªPassenger Bag Highº terminal ª15º allows a
known amount of current to flow. By monitoring the
voltage difference between ªPassenger Bag Highº and
ªPassenger Bag Lowº, the SDM calculates the combined
resistance of the passenger air bag assembly, harness
wiring CKTs IB07±YEL/GRN and IB08±YEL/RED
connector terminal contact.
DTC Will Set When:
The combined resistance of the passenger air bag
assembly, harness wiring CKTs IB07±YEL/GRN and
IB08±YEL/RED, and connector terminal contact is above
a specified value. This test is run once each ignition cycle
during the ªResistance Measurement Testº when:
1. No ªhigher priority faultsº are detected during
ªTurn±ONº,
2. ªIgnition 1º voltage is in the specified value.
Action Taken:
SDM turns ªONº the ªAIR BAGº warning lamp and sets a
diagnostic trouble code.
DTC Will Clear When:
The ignition switch is turned ªOFF.º

9J1±17
RESTRAINT CONTROL SYSTEM
DTC Chart Test Description:
Number(s) below refer to step number(s) on the
diagnostic chart:
2. This test determines whether the malfunction is in
the SDM.
3. This test verifies connection of the yellow 2±pin
connector.
4. This test cheeks for proper operation of the shorting
clip in the yellow 2±pin connector.
5. The test checks for a malfunction passenger air bag
assembly.
6. This test determines whether the malfunctioning is
due to shorting in the wiring.
Diagnostic Aids:
An intermittent condition is likely to be caused by a short
between CKTs IB07±YEL/GRN and IB08±YEL/RED, or a
malfunctioning shorting clip on the passenger air bag
assembly which would require replacement of the air bag
assembly. The test for this diagnostic trouble code is only
run while ªAIR BAGº warning lamp is performing the bulb
check, unless DTC 17 or DTC 26 is detected. When a
scan tool ªClear Codesº command is issued and the
malfunction is still present, the DTC will not reappear until
the next ignition cycle.

RESTRAINT CONTROL SYSTEM 9J1±18
DTC 16 Passenger Deployment Loop Resistance Low
StepActionYe sNo
1Was the ªSRS Diagnostic System Checkº performed?
Go to Step 2
Go to the ªSRS
Diagnostic
System Check.º
21. When measurements are requested in this chart use J±39200
DVM with correct terminal adapter from J±35616±A.
2. Using scan tool data list function, read and record the
passenger deployment loop resistance.
Is passenger resist. less than 1.4 ohms?
Go to Step 3 Go to Chart A .
31. Ignition switch ªOFF.º
2. Make sure the passenger air bag assembly yellow 2±pin
connector located behind the glove box assembly is seated
properly.
Is the yellow 2±pin connector connected properly?
Go to Step 4
Seat passenger
air bag assembly
yellow 2±pin
connector
properly.
Go to
Step 7
41. Disconnect and inspect the passenger air bag assembly
yellow 2±pin connector located behind the glove box
assembly.
2. If OK, reconnect the passenger air bag assembly 2±pin
connector.
3. Ignition switch ªON.º
Us DTC 16 current?
Go to Step 5
Ignition switch
ªOFF.ºGo to
Step
7

51. Ignition switch ªOFF.º
2. Disconnect SRS coil and passenger air bag 2±pin connectors
located at the base of the steering column and behind the
glove box assembly.
3. Connect J±41433 SRS driver / passenger load tool and
appropriate adapters to SRS coil and passenger air bag
assembly harness connectors.
4. Ignition switch ªON.º
Is DTC 16 current?
Go to Step 6 .
Ignition switch
ªOFF.º
Replace the
passenger air
bag assembly.
Go to
Step 7
61. Ignition switch ªOFF.º
2. There has been a decrease in the total circuit resistance of the
passenger inflator deployment loop.
3. Use the high resolution ohmmeter mode of the DVM while
checking CKTs IB07±YEL/GRN and IB08±YEL/RED, and
SDM connector terminal ª15º and ª16º to locate the root cause.
Was a fault found?
Replace SRS
harness.
Go to
Step 7 Go to Chart A .
71. Reconnect all components, ensure all component are properly
mounted.
2. Clear diagnostic trouble codes.
Was this step finished?
Repeat the ªSRS
Diagnostic
System Check.º
Go to Step 7