2002 ISUZU AXIOM sensor

6E±419
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P1154 ± HO2S Transition Time Ratio Bank 2 Sensor 1

 
StepNo Ye s Value(s) Action
21Replace Bank 2 HO2S 1.
Is the action complete?
ÐVerify repairÐ
22Replace the PCM.
IMPORTANT:The replacement PCM must be
programmed. Refer to
On-Vehicle Service in
Powertrain Control Module and Sensors for
procedures.
And also refer to latest Service Bulletin.
Check to see if the Latest software is released or not.
And then Down Load the LATEST PROGRAMMED
SOFTWARE to the replacement PCM.
Is the action complete?
ÐVerify repairÐ

6E±420
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC)
P1167 Fuel System Rich During Decel Fuel Cut Off (Bank 1)
060R200054
Circuit Description
The powertrain control module (PCM) continuously
monitors the heated oxygen sensor (HO2S) activity for 90
seconds after ªclosed loopº has been enabled. During the
monitoring period the powertrain control module (PCM)
counts the number of times a rich to lean response is
indicated and adds the amount of time it look to complete
all rich to lean transitions and lean to rich transitions.
This code detects if Bank1 O2 sensor indicated rich
exhaust while in Decel Fuel Cut Off (DFCO) for fuel
control sensors.
Conditions for setting the DTC

No related DTCs.

The engine coolant temperature is more than 60
C
(140
F).

Engine is operating in ªclosed loopº power enrichment
mode for 3 seconds.

While in ªpower enrichmentº mode the oxygen sensor
voltage remains more than 600mV in DFCO.
Action Taken When the DTC Sets

The PCM will not illuminate the malfunction
malfunction indicator lamp (MIL).

The PCM will store conditions which were present
when the DTC was set as Failure Records only. This
information will not be stored as Freeze Frame data.
Conditions for Clearing the MIL/DTC

A history DTC P1167 will clear after 40 consecutive trip
cycles during which the warm up cycles have occurred
without a fault.

DTC P1167 can be cleared using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids

Check for faulty fuel injectors and fuel pump.

6E±422
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC)
P1169 Fuel System Rich During Decel Fuel Cut Off (Bank 2)
060R200054
Circuit Description
The powertrain control module(PCM)
continuously monitors the heated oxygen sensor (HO2S)
activity for 90 seconds after ªclosed loopº has been
enabled. During the monitoring period the powertrain
control module (PCM) counts the number of times a rich
to lean response is indicated and adds the amount of time
it look to complete all rich to lean transitions and lean to
rich transitions.
This code detects if Bank2 sensor indicated rich exhaust
while in Decel Fuel Cut Off (DFCO) for fuel control
sensors.
Conditions for setting the DTC

No related DTCs.

The engine coolant temperature is more than 60
C
(140
F).

Engine is operating in ªclosed loopº power enrichment
mode for 3 seconds.

While in ªpower enrichmentº mode the oxygen sensor
voltage remains more than 600mV in DFCO.
Action Taken When the DTC Sets

The PCM will not illuminate the malfunction
malfunction indicator lamp(MIL).

The PCM will store conditions which were present
when the DTC was set as Failure Records only. This
information will not be stored as Freeze Frame data.
Conditions for Clearing the MIL/DTC

A history DTC P1169 will clear after 40 consecutive trip
cycles during which the warm up cycles have occurred
without a fault.

DTC P1169 can be cleared using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids

Check for faulty fuel injectors and fuel pump.

Check the pressure regulator.

6E±424
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC)
P1171 Fuel System Lean During Acceleration
060R200054
Circuit Description
The powertrain control module (PCM) internal circuitry
can identify if the vehicle fuel system is capable of
supplying adequate amounts of fuel during heavy
acceleration (power enrichment). The PCM monitors the
voltage of the oxygen sensor during power enrichment.
When a power enrichment mode of operation is
requested during ªclosed loopº operation (by heavy
acceleration), the PCM will provide more fuel to the
engine. Under these conditions the PCM should detect a
ªrichº condition (high oxygen sensor voltage). If this ªrichº
exhaust is not detected at this time, a DTC P1171 will set.
A plugged fuel filter, restricted fuel line, restricted in-tank
filter or defective fuel pump can prevent adequate
amounts of fuel from being supplied during power
enrichment mode.
Conditions for Setting the DTC

No related DTCs.

Engine is operating in ªclosed loop power enrichmentº
mode for 3 seconds.

Engine coolant temperature is above 60
C (140
F).

While in ªpower enrichmentº mode the oxygen sensor
voltage remains below 400 mV for 3 seconds.
Action Taken When the DTC Sets

The PCM will not turn the malfunction indicator lamp
(MIL) ªONº.

The PCM will store conditions which were present
when the DTC was set as Failure Records only. This
information will not be stored as Freeze Frame data.
Conditions for Clearing the MIL/DTC

The PCM will turn the MIL ªOFFº on the third
consecutive trip cycle during which the diagnostic has
been run and the fault condition is no longer present.

A history DTC P1171 will clear after 40 consecutive
warm-up cycles have occurred without a fault.

DTC P1171 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids

A restricted fuel filter or fuel line, restricted in-tank filter,
or a defective fuel pump may supply adequate
amounts of fuel at idle, but may not be able to supply
enough fuel during heavy acceleration.

Water or alcohol in the fuel may cause low HO2S
voltage during acceleration.

Check for faulty or plugged fuel injector(s).

Check for low fuel.

6E±427
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC)
P1220 Throttle Position Senser2 (TPS2) Circuit Fault
D06RY00111
Circuit Description

The throttle position (TP2) sensor circuit provides a
voltage signal relative to throttle blade angle.
The TPS2 voltage will vary from about 8% (0.4V) to
about 92% (4.6V) at Wide Open Throttle (WOT) in
the specified voltage (about 5V).
This code detects a continuous short to ground or
high in either the circuit or the sensor.
Conditions for setting the DTC

The Ignition is ªONº.

The TPS2 output is more than 93.6 milliseconds, less
than 2.5% or more than 97.5% in the specified voltage
(5V).
Action Taken When the DTC Sets

The PCM will ON the MIL after second trip with
detected fault.

The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC

The PCM will turn the MIL ªOFFº on the third
consecutive trip cycle during which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P1120 will clear after 40 consecutive trip
cycles during which the warm up cycles have occurred
without a fault.

DTC P1120 can be cleared using the Tech2 ªClear Infoº
function or by disconnecting the PCM battery feed.
Diagnostic Aids
An intermittent may be caused by the following:

Poor connections.

Misrouted harness.

Rubbed through wire insulation.

Broken wire inside the insulation.
Check for the following conditions:

The MAP sensor shares a 5 Volt reference with the
Fuel Tank Pressure. If these codes are also set, it could
indicate a problem with the 5 Volt reference circuit.

The MAP sensor shares a ground with the Fuel Tank
Pressure, the ECT sensor, and the Transmission Fluid

Poor connection at PCM-Inspect harness connectors
for backed out terminals,improper mating, broken
locks, improperly formed or damaged terminals, and
poor terminal to wire connection.

Damaged harness±Inspect the wiring harness for
damage. If the harness appears to be OK, observe the
TP sensor display on the Tech 2 while moving
connectors and wiring harnesses related to the sensor.
A change in the display will indicate the location of
the fault. If DTC P1120 cannot be duplicated, the

6E±428
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
information included in the Failure Records data can
be useful in determined vehicle mileage since the
DTC was last set.
If it is determined that the DTC occurs intermittently,
performing the DTC
P1120 Diagnostic Chart may isolate the cause of the
fault.
DTC P1220-TPS 2 Circuit Fault

StepActionValue(s)Ye sNo
1Was the ªOn-Board (OBD) System Checkº performed?
ÐGo to Step 2
Go to OBD
System
Check
2Was the ªElectric Throttle Control (ETC) System
Checkº performed?
ÐGo to Step 3
Go to ETC
System
Check
31. Ignition ªONº, engine not running.
2. Observe the MAP reading on the Tech 2.
Is the MAP reading less than the specified value?
65 kPaGo to Step 4Go to Step 7
41. Disconnect the MAP sensor.
2. Connect a test 5 volt reference circuit and the MAP
signal at the MAP sensor harness connector.
3. Observe the MAP reading on the Tech 2.
Is the MAP reading less than the specified value? (If no,
start with diagnosis chart for other sensors in the circuit
and see if 5V returns.)
ÐGo to Step 6Go to Step 5
51. Check the MAP signal circuit between the PCM and
MAP ground circuit.
2. If the MAP signal circuit is open or shorted, repair as
necessary.
Was the MAP signal circuit open or shorted?
ÐVerify repairGo to Step 13
6Replace the MAP sensor.
Is the action complete?
ÐVerify repairÐ
7Observe the TP angle reading on the Tech-2 while
slowly opening the throttle.
Does the TP angle increase steadily and evenly from
the closed throttle value to the wide open throttle
value?Closed TPS1
8±10 % TPS2
8±10 % WTO
TPS1 90±92
% TPS2
90±92 %
Refer to
Diagnostic
Aids
Go to Step 8
81. Disconnect the TP sensor.
2. Observe the TP sensor reading on the Tech2.
Is the TP sensor reading near the specified value?
0VGo to Step 9Go to Step 10
91. Connect a test light between the 5Volt reference
circuit and the TP2 sensor signal circuit at the TP
sensor harness connector.
2. Observe the TP sensor reading on the Tech 2.
Is the TP sensor reading near the specified value?
5VGo to Step 12Go to Step 11

6E±429
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P1220-TPS 2 Circuit Fault

 
StepNo Ye s Value(s) Action
10Check the following items;
1. TP2 signal circuit for a short to voltage.
2. TP2 sensor ground circuit for high resistance
between the PCM and the TP2 sensor.
3. TP2 sensor ground circuit for a poor connection.
4. If a problem is found, repair wiring harness as
necessary.
Was a problem found?
ÐVerify repairGo to Step 13
11Check the following items;
1. TP2 signal circuit or 5 volt reference circuit for a
poor connection.
2. TP2 signal circuit or 5 volt reference circuit for high
resistance between the PCM and the TP sensor.
3. If a problem is found, repair wiring harness as
necessary.
Was a problem found?
ÐVerify repairGo to Step 13
12Replace the TP sensor.
Is the action complete?
ÐVerify repairÐ
13Replace the PCM.
IMPORTANT:The replacement PCM must be
programmed. Refer to
ON-Vehicle Service in Power
Control Module and Sensors for procedures.
And also refer to latest Service Bulletin. Check to see
if the latest software is released or not.
And then Down Load the LATEST PROGRAMMED
SOFTWARE to the replacement PCM.
Is the action complete?
ÐVerify repairÐ

6E±430
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnosis Trouble Code(DTC)
P1221 TPS1 ± TPS2 Correlation(Circuit Performance)
060R200069
Circuit Description

The powertrain control module (PCM) controls engine
speed by adjusting the position of the throttle control
valve (DC motor). The throttle motor is a DC motor
driven by one coil. The PCM applies current to DC
motor coil in duty (%) to adjustment the valve into a
passage in the throttle body to air flow.
This method allows highly accurate control of engine
speed and quick response to changes in engine
load.

The accelerator position (AP) sensor circuit provides a
voltage signal relative to accelerator pedal angle.
The accelerator pedal angle (AP1) will vary from
about 13% at idle position to about 87% at open
throttle(WOT).
APS signal is used to determine which DC will adjust
throttle position.
After the APS signal has been processed by the
PCM, it will command the DC motor to move the
throttle position.

Accelerator pedal ± Check for objects blocking the AP
sensor or pedal arm with spring, and excessive
deposits in the accelerator pedal arm and on the
accelerator pedal.
Conditions for Setting the DTC

The ignition is ªONº.
A difference of between TPS1 and TPS2 correlation of
over 6.5% within 125 milliseconds.
Action Taken When the DTC Sets

The PCM will not turn the malfunction indicator lamp
(MIL) ªONº.

The PCM will store conditions which were present
when the DTC was set as Failure Records only. This
information will not be stored as Freeze Frame data.
Condition for Clearing the MIL/DTC

A history DTC 1221 will clear after 40 consecutive trip
cycles during which the warm up cycles have occurred
without a fault.

DTC 1221 can be cleared using the Tech 2 ªClear Infoº
function or by disconnecting the PCM battery feed.
Test Description
Number(s) below refer to the step number(s) on the
Diagnostic Chart:
2. Visually/physically inspect for the following throttle
valve conditions.
3.Visually/physically inspect for the following
accelerator pedal conditions.
5.Check the following circuits for throttle valve and DC
moter. Check the following TP sensor resistance
and DC motor.