2002 HONDA PASSPORT cooling

218Care and Maintenance
You usually do not need to remove
the radiator cap to check the engine
coolant level.
Removing the radiator cap
while the engine is hot can
cause the coolant to spray
out, seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
Adding Engine Coolant
To add engine coolant, remove the
cap on the radiator reserve tank
and fill the tank up to the
maximum level mark. Add a
50/50 mixture of water and a good
quality ethylene glycol antifreeze.
If you need to add engine coolant
frequently, see your Honda dealer
for a cooling system check.
If the proper quality antifreeze
is used, there is no need to add
extra inhibitors or additives. They
may be harmful to the proper
operation of the system.
Cooling System Service
The cooling system should be
serviced at the intervals specified
in the Maintenance Schedule as
follows:
•Wash the radiator cap and filler
neck with clean water.
•Check the engine coolant level
in the radiator and have it tested
for freeze protection. Add
ethylene glycol antifreeze, if
needed, to maintain freeze
protection at
–33
F ( –36
C).
•Have the cooling system and
radiator cap tested for a
pressure capacity of 15 psi (105
kPa). If a replacement cap is
needed, use a cap specified for
your model.
•Tighten all radiator and heater
hose clamps and inspect all
hoses. Replace the hoses if they
are swollen, “checked, ” or
otherwise worn. Carefully
tighten the hose clamps at the
radiator. Overtightening could
bend or collapse the radiator
fittings.
•Clean the front of the radiator
core and air conditioning
condenser.
It is the owner ’s responsibility to:
•Maintain the cooling system
freeze protection at –33
F

221Care and Maintenance
Hood Latch and Hinges
Lubricate the hood latch assembly
and hood hinge assembly as
follows:
1. Wipe off any accumulation ofdirt or contamination on the
latch parts.
2. Apply multipurpose-type grease (
NLGI No. 1 or 2) to
the hood latch pin cam.
3. Apply light engine oil to all pivot points in the release
mechanism.
4. Lubricate hood hinges with multipurpose-type grease
(
NLGI No. 1 or 2).
5. Check the hood hinges and latch mechanism to assure
they are working correctly.
Air Conditioning
Periodically have your Honda
dealer check your air conditioning
system to be sure there has been
no loss in cooling output. See
your Honda dealer if you suspect
that the system is not performing
as it should.
Body Lubrication
Normal use of a vehicle causes
metal-to-metal movement at certain
points in the body. Noise, wear and
improper operation at these points
will result when a protective film
of lubricant is not provided.
For exposed surfaces such as door
checks, door lock bolts, lock
striker plates, etc., apply a thin
film of light engine oil.
Any lubricant should be used
sparingly. After application, all excess lubricant should be
carefully wiped off.
The seat adjusters and seat track
should be lubricated with water-
resistant
EP chassis lubricant.
There are other points on the
vehicle body which may
occasionally require lubrication.
Window regulators and controls
are confined in the space between
the upholstery and the outside
door panel. Easy access to the
working parts may be made by
removing the trim. Door
weatherstrips and rubber hood
bumpers should be lightly coated
with a rubber lubricant.

236Technical Data
Cooling System
Radiator typeTube and corrugated fins pressure type
Capacity11.2 U.S. quarts (10.6 liters) for MT
11.1 U.S. quarts (10.5 liters) for AT
ThermostatWax pellet type 170
F (76.5
C)
Air Conditioning
Refrigerant typeR-134a
Charge quantity22.9 oz (650g)
Lubricant typePAG oil
Clutch
TransmissionMUA
Clutch size10.24 in. (260 mm)
TypeDry single plate disc with diaphragm spring
Clutch control
operationHydraulic
Clutch pedal
free play0.2 in. – 0.6 in.
(5 mm – 15 mm)

259
Foreign Countries, Operation in
173. . . . . . . . . . . . .
Fuel Filling the Fuel Tank
197. . . . .
Fuel Fill Cap
197. . . . . . . . . . .
Fuel Gauge
59. . . . . . . . . . . . .
Low Fuel Indicator
64. . . . . .
Octane Requirement
200. . . . .
Oxygenated
200. . . . . . . . . . . .
Recommendation
198. . . . . . . .
Tank Capacity
198, 237. . . . . .
Fuel Injection System
249. . . . . .
Fuses Checking the
193, 240. . . . . . .
Locations
240. . . . . . . . . . . . . .
G
Gas Mileage, Improving170. . . . Gasohol
200. . . . . . . . . . . . . . . . .
Gasoline
200. . . . . . . . . . . . . . . . .
See also Fuel
Octane Requirement
200. . . . .
Tank, Filling the
197. . . . . . . . . . . .
Gas Station Procedures
197. . . . .
Gauges Engine Coolant Temperature
60. . . . . . . . . . .
Fuel
59. . . . . . . . . . . . . . . . . .
Speedometer
58. . . . . . . . . . .
Tachometer
58. . . . . . . . . . . .
GAWR (Gross Axle
Weight Rating)
233. . . . . . . . . . .
Gearshift Lever Positions Automatic Transmission
76. .
5-Speed Transmission
83. . . .
Glass Cleaning
230. . . . . . . . . . . . Glove Box
114. . . . . . . . . . . . . . .
GVWR (Gross Vehicle
Weight Rating)
233. . . . . . . . . .
H
Halogen Headlight Bulbs243. . . .
Hazard Warning Flasher
76. . . .
Head Restraints
8, 12, 93. . . . . . .
Headlights
72. . . . . . . . . . . . . . .
High Beam Indicator
62. . . . .
High Beams
72. . . . . . . . . . . .
On, Reminder
73. . . . . . . . . .
Replacing Halogen Bulbs
243.
Turning on
72. . . . . . . . . . . . .
Heating and Cooling
120. . . . . . .
High-Low Beam Switch
72. . . .
Hood Release
109, 199. . . . . . . . .
Horn
115. . . . . . . . . . . . . . . . . . . .
Hydroplaning
168. . . . . . . . . . . . .