2002 HONDA CIVIC battery

PGM-FI System
MIL Circuit Troubleshooting (cont'dl
37. lvleasure voltage between ECM/PCM connector
terminal E7 and body ground.
ECM CONNECTOR E {31PI
Wire side of female terminals
ls there battery voltage?
YES Go to step 42.
NO Go to step 38.
Turn the ignition switch OFF.
Remove the PGM-FI main relay 1
38.
39.{A}
-A
MRLY
11-102
40. lvleasure voltage between PGN4-Fl main relay 1 4P
connector terminal No. 4 and bodv qround.
PGM-FI MAIN RELAY 1ilP CONNECTOR
41.
ls there battery voltage?
YES-Go to step 41.
NO Repair open in the wire between the No. 6
ECU (ECM) (15A) fuse and the PGfM-Fl main relay 1.
I
Check for continuity between PGM-FI main relay 1
4P connector terminal No. 3 and ECM connector
terminal E7.
PGM.FI MAIN RELAY 14P CONNECTOR
\
ECM CONNECTOR E 131PI
ls there continuity?
YES-Testthe PGM-Fl main relay 1 (see page 22-
51 ). lf the relay is OK, update the ECM if it does not
have the latest software, or substitute a known-
good ECM, then recheck {see page 1 1'6). lf the
symptom/indication goes away with a known-good
ECM, replace the original ECM.I
NO*Repair open in the wire between the PGM-FI
main relay 1 and the ECM (E7).1
Wire side ot lemale terminals
MRLY (RED/YEL)
MRLY (RED/YEL)
Wire side of female terminals

42.
43.
44.
45.
46.
Reconnect ECI\4 connector E {31P).
Turn the ignition switch ON (ll).
Measure voltage between body ground and ECM
connector terminals 42 and 43 individually.
Wire side of female terminals
ls there battery voltage?
YES Go to step 51.
NO Go to step 45.
Turn the ignition switch OFF.
Remove the PGM'Fl main relay 1{A)
,A
47. Turn the ignition switch ON (ll).
ECM CONNECTOR A {31PI
49.
50.
48. Measure voltage between PGM-FI main relay 1 4P
connector terminal No. 2 and body ground.
PGM.FI MAIN RELAY 14P CONNECTOR
ls there battery voltage?
YES Go to step 49.
NO Repair open in the wire between the No.6
ECU {ECM) (15A}fuse and the PGM-Fl main
relay 1 . !
Turn the ignition switch OFF.
Check for continuity between PGM-Fl main relay 1
4P connector terminal No. 1 and ECM connector
terminals 42 and 43 individually.
PGM.FI MAIN RELAY IilP CONNECTOR
ls there continuity?
YES Replace the PGM-Fl main relay 1.1
NO Repair open in the wire between the PGM-FI
main relay '1 and the ECM (A2, A3).1
{cont'd}
Wire side of temale terminals
IGPl (YEL/BLK)
Wire side of female terminals
11-103

13.
74.
75.
72. Measure voltage between body ground and ECM
connector terminal E5.
ECM CONNECTOR E 131P}
ls there about 5 V?
YES Replace the FTP sensor.t
NO Go to step 73.
Turn the ignition switch OFF.
Disconnect ECM connector E (3'lP).
Check for continuity between ECM connector
terminal E5 and body ground.
ECM CONNECTOR E {31PI
Is there continuity?
YES Repair short in the wire between the ECM(E5) and the FTP sensor.l
NO Update the ECM if it does not have the latest
software, or substitute a known-good ECM, then
recheck (see page 11-6). lf the symptom/indicationgoes away with a known-good ECM, replace the
original ECM.I
Wire side of female terminals
Wire side of female terminals
76.
77.
78.
79.
80.
Turn the ignition switch OFF.
Turn the ignition switch ON (ll).
Measure voltage between ECM connector terminal
E29 and body ground.
ECM CONNECTOR E (31P)
rl2l31456189
,/1,/1141562A212223241 l,/2930
scstBRN)
Wire side of female terminals
ls there about 5 V (or battery voltage)?
YES-Go to step 82.
NO Go to step 79.
Turn the ignition switch OFF.
Disconnect ECM connector E (31P).
(cont'd)
11-107

DLC Circuit Troubleshooting
lf the ECM does not communicate with the OBD ll scan
tool, Honda PGfM Tester, or l/M test equipment, do this
troubleshooting procedure.
1. Measure voltage between DLC terminal No. 16 and
body ground.
DATA LINK CONNECTOR {DLCI
(WHT/RED)
Terminal side of lemale terminals
ls therc battery voltage?
YES-Go to step 2.
NO-Repair open in the wire between DLC terminal
No. 16 and the No. 9 BACK UP (7.5 A) fuse in the
under-hood f use/relay box. I
Measure voltage between DLC terminals No. 4 and
No. 16.
DATA LINK CONNECTOR (DLCI
Terminal side of Jemale terminals
Is there battery voltage?
YES Go to step 3.
NO Repair open in the wire between DLC terminal
No. 4 and body ground.l
4.
5.
3. Measure voltage between DLC terminals No. 5 and
No. 16.
DATA LINK CONNECTOR {DLC)
Terminal side of female terminals
ls there battery voltage?
YES Go to step 4.
NO- Repair open in the wire between DLC terminal
No. 5 and the ECM (E3). t
Turn the ignition switch ON {ll).
Measure voltage between DLC terminals No.5 and
No.7.
DATA LINK CONNECTOR {DLCI
Terminal side of lemale terminals
ls there 8.5 V or more?
YES Go to step 10.
NO Go to step 6.
6. Turn the ignition switch OFF.
(cont'd)
11-109

VTEC/VTC
DTC Troubleshooting (cont'd)
10. Measure voltage between ECM connectorterminal
89 and body ground.
ECM CONNECTOR B (24P)
213 415o1
8Iat/t/n315
WPSW {BLU/BLK}
Wire side of Iemale terminals
ls there battery voltage?
YES Repair open in the wire between the VTEC oilpressure switch and the ECM (89).t
NO-Go to step 11.
Turn the ignition switch OFF.
Disconnect ECM connector B {24P).
Check for continuity between ECM connector
terminal Bg and body ground.
ECM CONNECTOR B {24P)
2 3 41567
I9ol./ ./ 1315
VTPSW {BLU/BLK}
Wrre side of female terminals
ls there continuity?
YES Repair short in the wire between the VTEC oilpressure switch and the ECM (89).I
NO Update the ECM if it does not have the latest
software. or substitute a known-good ECM, then
recheck (see page 1 1-6). lf the symptom/indication
goes away with a known-good ECM, replace the
original ECN4. !
11.
11-124
2P CONNECTOR
VTPSW(BLU/BLK)
14. fMeasure voltage between VTEC oil pressure switch
2P connector terminals No. 1 and No. 2,
VTEC OIL PRESSURE SWITCH
(BRN/YELI
Wire side of Iemale terminals
ls there battery voltage?
YES-Go to step 15.
NO Repair open in the wire between the VTEC oil
pressure switch and G 101.1
Turn the ignition switch OFF.
Disconnect the VTEC solenoid valve 2P connector.
Check for resistance between VTEC solenoid valve
2P connector terminals No, 1 and No. 2.
VTEC SOLENOID VALVE2P CONNECTOR
Terminal side of male terminals
ls there 14- 30 Sl ?
YES Go to step 18.
NO Replace the VTEC solenoid valve (see page
11-128).t
to.
17.

18.Remove the VTEC oil pressure switch (A) and
installthe specialtools as shown, then reinstall the
VTEC oil pressure switch.
07406-0070300
\lsl
t:={
R
07406-0020201 ot07MAJ-PY,lo11A and07MAJ-PY40120
A22 N.ml2.2kgt.m,16 rbf.ft)
19.
20.
21.
22.
07NAJ-P07010A
Reconnect the VTEC solenoid valve 2P connector
and VTEC oil pressure switch 2P connector.
Connect a tachometer or OBD ll scan tool/Honda
PGM Tester to the DLC.
Start the engine. Hold the engine at 3,000 rpm with
no load (in neutral) until the radiator fan comes on.
Checkthe oil pressure at engine speeds of 1,000
and 2.000 rpm. Keep the measuring time as shon
as possible {less than 1 minute) because the engine
is running with no load.
ls the oil ptessure below 49 kPa (0.5 kgf/cnf,
7 psi)?
YES Go to step 23.
NO Inspect the VTEC solenoid valve (see page 11-'t28l.a
23.
24.
25.
26.
Turn the ignition switch OFF.
Disconnect the VTEC solenoid valve 2P connector.
Aftach the battery positive terminalto VTEC
solenoid valve 2P connector terminal No. 2.
Start the engine, then connect the battery negative
terminalto VTEC solenoid valve 2P connector
terminal No. 1, and check the oil pressure at an
engine speed of 3,000 rpm.
ls the oil pressure above 390 kPa (4.0 kgt/crtf ,
57 psi)?
YES Go to step 27.
NO Inspectthe VTEC solenoid valve (see page I1-
12Al.a
27. With the battery terminals still connectedtothe
VTEC solenoid valve connector, measure voltage
between ECM connector terminal 89 and bodv
oround.
ECM CONNECTOR B {24P)
ls there battery voltage above 4,000 tpm?
YES Go to step 28.
NO-Replace the VTEC oil pressure switch (see
page 11'128).1
Turn the ignition switch OFF.
Disconnect the battery terminals from the VTEC
solenoid valve terminal connector.
(cont'd)
28.
29.
Wire side of female terminals
11-125

WC OilControl Solenoid Valve Removal/Test
1. Remove the WC oilcontrol solenoid valve (A).
NOTE: lnstall the valve in the reverse order of
removal with a new o-ring (B), then check these
tlems:
Clean and dry the VTC oil control solenoid valve
mating surface.
Coat the O-ring with engine oil.
Do not install the VTC oilcontrol solenoid valve
while wearing fibrous gloves,
Be careful not to contaminate the cylinder head
openrng.
Check the VTC oil control solenoid valve filter for
clogging. lf it is clogged, replace the VTC oil control
solenoid valve.
Check the clearance between the port (advance
side) and the valve. The clearance (A) should be at
least 2.8 mm (1/8 in.).
Connect the battery positive terminal to VTC oil
control solenoid valve 2P connector terminal No. 2.
VTC OIL CONTROL SOLENOIDVALVE 2P CONNECTOR
Terminal side oJmale terminals
Connect the battery negative terminal to VTC oil
control solenoid valve 2P connector terminal No. 1,
then make sure the valve (A) opens fully.
BATTERY
11-127

DTC Pl519: IAC Valve Circuit Malf unction
1. Resetthe ECM (see page 11-4).
2. Turn the ignition switch ON (ll)
ls DTC P 1519 indicated?
YES Go to step 3.
NO-lntermittent failure, system is OK at this time.
Check for poor connections or loose terminals at
the IAC valve and at the ECM.I
3. Turn the ignition switch OFF.
4. Disconnect the IAC valve 3P connector.
5. Turn the ignition switch ON (ll).
6. Measure voltage betlveen IAC valve 3P connector
terminal No. 2 and body ground.
IAC VALVE 3P CONNECTOR
IGP {YEL/BLK)
Wire side of female terminals
ls there battery voltage?
YES Go to step 7.
NO-Repair open in the wire between the IAC valve
and the PGM-Fl main relay 1.1
Turn the ignition switch OFF.
123
7.
8, Check for continuity between body ground and IAC
valve 3P connector terminal No. 1.
IAC VALVE 3P CONNECTOR
123
PG1 {BLK}
a.
Wire side of lemale terminals
Is there continuity?
YES-Go to step 9.
NO Repair open in the wire between the IAC valve
and G'101.1
Disconnect ECM connector A (31P)
Check for continuity between body ground and
ECM connector terminal A12.
ECM CONNECTOR A 131P)
r l2l3l4 5617s
r01l12 .// 1156 ./118192C21
da25126l27ln2930
IACV {BLK/RED}
1,)
Wire side oJ Jemale terminals
ls there continuity?
YES-Repair short in the wire between the IAC
valve and the ECM (A12).1
NO Go to step 1 1.
9.
10.
LCOnI Ol
11-131