2002 DODGE RAM tires

DIAGNOSIS AND TESTING
WHEEL INSPECTION
Inspect wheels for:
²Excessive run out
²Dents or cracks
²Damaged wheel lug nut holes
²Air Leaks from any area or surface of the rim
NOTE: Do not attempt to repair a wheel by hammer-
ing, heating or welding.
If a wheel is damaged an original equipment
replacement wheel should be used. When obtaining
replacement wheels, they should be equivalent in
load carrying capacity. The diameter, width, offset,
pilot hole and bolt circle of the wheel should be the
same as the original wheel.
WARNING: FAILURE TO USE EQUIVALENT REPLACE-
MENT WHEELS MAY ADVERSELY AFFECT THE
SAFETY AND HANDLING OF THE VEHICLE. USED
WHEELS ARE NOT RECOMMENDED. THE SERVICE
HISTORY OF THE WHEEL MAY HAVE INCLUDED
SEVERE TREATMENT OR VERY HIGH MILEAGE. THE
RIM COULD FAIL WITHOUT WARNING.
STANDARD PROCEDURE - DUAL REAR WHEEL
INSTALLATION
Dual rear wheels use a special heavy duty lug nut
wrench. It is recommended to remove and install dual
rear wheels only when the proper wrench is available.
The wrench is also use to remove wheel center caps for
more information refer to Owner's Manual.
The tires on both wheels must be completely raised
off the ground when tightening the lug nuts. This
will ensure correct wheel centering and maximum
wheel clamping.
A two piece flat face lug nut with right-hand
threads is used for retaining the wheels on the hubs
(Fig. 20).The dual rear wheel lug nuts should be tightened
according to the following procedure:
²Place two drops of oil to the interface of the nut/
washer (Fig. 20) before installing on the wheel stud.
NOTE: Do not use more then two drops of oil on
the nut/washer, since the center caps attach in this
area.
²Tighten the wheel lug nuts in the numbered
sequential pattern until they are snug tight. Then
tighten lug nut to specified torque following same
number sequence, (Refer to 22 - TIRES/WHEELS/
WHEELS - SPECIFICATIONS).
²Tighten lug nuts in same numbered sequence a
second time to the specified torque. This will ensure
that the wheels are thoroughly mated.
²Check lug nut specified torque after 100 miles
(160 kilometers). Also after 500 miles (800 kilome-
ters) of vehicle operation.
NOTE: Wheel lug nuts should be tightened to spec-
ified torque at every maintenance interval thereafter.
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION N´m Ft. Lbs. In. Lbs.
Lug Nut
BR2500 (8 Stud Wheel)180 135 Ð
Lug Nut
BR3500 (8 Stud Dual
Wheel)195 145 Ð
Fig. 20 Oil Location
1 - PLACE TWO DROPS OF OIL HERE
BR/BETIRES/WHEELS 22 - 11
WHEELS (Continued)

STUDS
REMOVAL
(1) Raise and support the vehicle.
(2) Remove the wheel and tire assembly.
(3) Remove the brake caliper, caliper adapter and
rotor, (Refer to 5 - BRAKES/HYDRAULIC/MECHAN-
ICAL/ROTORS - REMOVAL).
(4) Remove the stud from the hub with Remover
C-4150A (Fig. 21).
INSTALLATION
(1) Install the new stud into the hub flange.
(2) Install the three washers onto the stud, then
install the lug nut with the flat side of the nut
against the washers.
(3) Tighten the lug nut until the stud is pulled
into the hub flange. Verify that the stud is properly
seated into the flange.
(4) Remove the lug nut and washers.
(5) Install the brake rotor, caliper adapter, and cal-
iper, (Refer to 5 - BRAKES/HYDRAULIC/MECHAN-
ICAL/ROTORS - INSTALLATION).
(6) Install the wheel and tire assembly, (Refer to
22 - TIRES/WHEELS/WHEELS - STANDARD PRO-
CEDURE), use new the lug nut on stud or studs that
were replaced.
(7) Remove the support and lower vehicle.
WHEEL COVER
REMOVAL
(1) Insert a hub/cap remover/installer combination
tool around the circumference of the wheel between
the wheel and wheel trim cover.
(2) Twist the tool to remove wheel trim cover.
INSTALLATION
INSTALLATION - REAR
(1) Install one 1 1/2 in. valve stem extension on
each rear inner wheel.
NOTE: A 3/8 in. drive 10mm deep wheel socket with
a 10 in. or greater extension can be used to remove
the existing valve stem cap and install the exten-
sion.
(2) Install one 1 in. valve stem extension on each
outer wheel.
(3) Align the cooling windows of the wheel skin
with the cooling windows of the wheel. Seat one side
of the wheel skin's retainer onto the wheel. Using a
rubber mallet, strike thew wheel skin on the outer
circumference. Strike at several locations around the
circumference until the skin is fully seated.
NOTE: The wheel skin and the hub cap are fully
seated when there is a consistent gap between the
skin/cap and the wheel.
(4) Tug on the hub/cap wheel skin to ensure that
they are properly installed.
INSTALLATION - FRONT
(1) Align the valve stem with the notch in the
wheel skin.
(2) Seat on side of the wheel skin's wire retainer
on to the wheel.
(3) Using a rubber mallet, strike the opposite side
of the wheel skin until the skin is properly seated.
NOTE: The wheel skin and the hub cap are fully
seated when there is a consistant gap between the
skin/ cap and the wheel.
(4) Tug on the hub cap/wheel skin to ensure that
they are properly installed.
Fig. 21 Wheel Stud Removal
1 - REMOVER
2 - WHEEL STUD
22 - 12 TIRES/WHEELSBR/BE

PRESSURE SWITCH - OPERATION, A/C
HIGH..............................24-20
PRESSURE SWITCH - OPERATION, A/C
LOW ..............................24-21
PRESSURE SWITCH - REMOVAL, A/C
HIGH..............................24-20
PRESSURE SWITCH - REMOVAL, A/C
LOW ..............................24-21
PRESSURE TEST - DIAGNOSIS AND
TESTING, FUEL PUMP..................14-9
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC...........21-270,21-98
PRESSURES - DESCRIPTION, TIRE
INFLATION...........................22-7
PRESSURES, DIESEL ENGINES - FUEL
SYSTEM............................14-62
PROGRAMMING - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-8
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - FRONT -
INSTALLATION.........................3-7
PROPELLER SHAFT - FRONT - REMOVAL . . . 3-6
PROPELLER SHAFT - REAR -
INSTALLATION.........................3-7
PROPELLER SHAFT - REAR - REMOVAL....3-7
PROPELLER SHAFT - STANDARD
PROCEDURES.........................3-3
PROPELLER SHAFT, SPECIAL TOOLS.......3-6
PROPELLER SHAFT, SPECIFICATIONS.......3-6
PTO SWITCH - DESCRIPTION...........14-47
PTO SWITCH - OPERATION..............14-47
PULLEY - INSTALLATION..............19-39
PULLEY - REMOVAL..................19-38
PUMP - 5.9L - CLEANING, WATER........7-68
PUMP - 5.9L - DESCRIPTION, WATER.....7-66
PUMP - 5.9L - INSPECTION, WATER......7-68
PUMP - 5.9L - INSTALLATION, WATER.....7-68
PUMP - 5.9L - OPERATION, WATER.......7-66
PUMP - 5.9L - REMOVAL, WATER........7-66
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-72
PUMP - 5.9L DIESEL - DESCRIPTION,
VACUUM............................7-33
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER .............................7-72
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-72
PUMP - 5.9L DIESEL - INSTALLATION,
VACUUM............................7-36
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-72
PUMP - 5.9L DIESEL - OPERATION,
VACUUM............................7-34
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-72
PUMP - 5.9L DIESEL - REMOVAL,
VACUUM............................7-34
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-72
PUMP - 8.0L - CLEANING, WATER........7-71
PUMP - 8.0L - INSPECTION, WATER......7-71
PUMP - 8.0L - INSTALLATION, WATER.....7-71
PUMP - 8.0L - REMOVAL, WATER........7-69
PUMP - ASSEMBLY, OIL................9-49
PUMP - ASSEMBLY, OIL........21-169,21-340
PUMP - CLEANING, OIL..........9-104,9-181
PUMP - CLEANING, OIL........21-168,21-338
PUMP - DESCRIPTION................19-33
PUMP - DESCRIPTION, AIR INJECTION . . . 25-29
PUMP - DESCRIPTION, FUEL
............14-9
PUMP - DESCRIPTION, FUEL TRANSFER
. . 14-83
PUMP - DESCRIPTION, LEAK DETECTION
. 25-34
PUMP - DESCRIPTION, OIL
......21-166,21-336
PUMP - DIAGNOSIS AND TESTING, AIR
INJECTION
..........................25-29
PUMP - DIAGNOSIS AND TESTING,
WATER
.....................7-66,7-69,7-72
PUMP - DISASSEMBLY, OIL
.............9-47
PUMP - DISASSEMBLY, OIL
.....21-167,21-337
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING
..........................19-33
PUMP - INSPECTION, OIL
.....9-104,9-181,9-47
PUMP - INSPECTION, OIL
.......21-168,21-339
PUMP - INSTALLATION, AIR INJECTION
. . . 25-30
PUMP - INSTALLATION, FUEL TRANSFER
. 14-87PUMP - INSTALLATION, LEAK
DETECTION.........................25-34
PUMP - INSTALLATION, OIL . . . 9-106,9-182,9-50
PUMP - OPERATION..................19-33
PUMP - OPERATION, AIR INJECTION.....25-29
PUMP - OPERATION, FUEL..............14-9
PUMP - OPERATION, FUEL TRANSFER....14-83
PUMP - OPERATION, LEAK DETECTION . . . 25-34
PUMP - OPERATION, OIL.......21-166,21-336
PUMP - REMOVAL, AIR INJECTION......25-30
PUMP - REMOVAL, FUEL TRANSFER.....14-86
PUMP - REMOVAL, LEAK DETECTION....25-34
PUMP - REMOVAL, OIL.......9-104,9-181,9-47
PUMP 235 H.P. - DESCRIPTION, FUEL....14-69
PUMP 245 H.P. - DESCRIPTION, FUEL....14-69
PUMP AMPERAGE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-10
PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION,
WATER .............................7-76
PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL, WATER......7-73
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER .............................7-77
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER......7-76
PUMP CAPACITY TEST - DIAGNOSIS
AND TESTING, FUEL...................14-9
PUMP DATA PLATE, SPECIFICATIONS -
FUEL INJECTION.....................14-77
PUMP FILTER - INSTALLATION, AIR......25-30
PUMP FILTER - REMOVAL, AIR.........25-30
PUMP LEAKAGE - DIAGNOSIS AND
TESTING...........................19-33
PUMP MODULE - DESCRIPTION, FUEL....14-12
PUMP MODULE - INSTALLATION, FUEL . . . 14-13
PUMP MODULE - OPERATION, FUEL.....14-13
PUMP MODULE - REMOVAL, FUEL.......14-13
PUMP OUTPUT - DIAGNOSIS AND
TESTING, VACUUM....................7-34
PUMP PRESSURE - DIAGNOSIS AND
TESTING, FUEL TRANSFER.............14-84
PUMP PRESSURE TEST - DIAGNOSIS
AND TESTING, FUEL...................14-9
PUMP RELAY - DESCRIPTION, FUEL.....14-40
PUMP RELAY - DESCRIPTION, FUEL
INJECTION.........................14-103
PUMP RELAY - INSTALLATION, FUEL.....14-40
PUMP RELAY - OPERATION, FUEL.......14-40
PUMP RELAY - OPERATION, FUEL
INJECTION.........................14-103
PUMP RELAY - REMOVAL, FUEL........14-40
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-4
PUMP, SPECIAL TOOLS - POWER
STEERING..........................19-38
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION.............14-70
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL.............21-166,21-336
PUMP/MOTOR - DESCRIPTION, WASHER . . 8R-9
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-10
PUMP/MOTOR - OPERATION, WASHER....8R-9
PUMP/MOTOR - REMOVAL, WASHER....8R-10
PUSHRODS - CLEANING...............9-134
PUSHRODS - INSPECTION.............9-135
QUARTER TRIM PANEL - INSTALLATION . 23-128
QUARTER TRIM PANEL - REMOVAL.....23-128
QUARTER WINDOW - INSTALLATION....23-150
QUARTER WINDOW - REMOVAL
........23-150
QUICK CONNECT FITTING -
DESCRIPTION
.......................14-24
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE
........................14-24
RADIAL-PLY TIRES - DESCRIPTION
.......22-6
RADIATOR - 5.9L - CLEANING
...........7-59
RADIATOR - 5.9L - DESCRIPTION
........7-58
RADIATOR - 5.9L - INSPECTION
..........7-60
RADIATOR - 5.9L - INSTALLATION
........7-60
RADIATOR - 5.9L - OPERATION
..........7-58
RADIATOR - 5.9L - REMOVAL
............7-58
RADIATOR - 5.9L DIESEL - CLEANING
.....7-64
RADIATOR - 5.9L DIESEL -
DESCRIPTION
........................7-62
RADIATOR - 5.9L DIESEL - INSPECTION
. . . 7-64RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-64
RADIATOR - 5.9L DIESEL - OPERATION....7-62
RADIATOR - 5.9L DIESEL - REMOVAL.....7-62
RADIATOR - 8.0L - CLEANING...........7-61
RADIATOR - 8.0L - DESCRIPTION........7-60
RADIATOR - 8.0L - INSPECTION..........7-61
RADIATOR - 8.0L - INSTALLATION........7-61
RADIATOR - 8.0L - OPERATION..........7-60
RADIATOR - 8.0L - REMOVAL............7-60
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-65
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-65
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING......7-58,7-60,7-62
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-43
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-43
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-44
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-43
RADIATOR FAN - 5.9L/8.0L - CLEANING....7-42
RADIATOR FAN - 5.9L/8.0L -
INSPECTION.........................7-42
RADIATOR FAN - 5.9L/8.0L -
INSTALLATION........................7-42
RADIATOR FAN - 5.9L/8.0L - REMOVAL....7-41
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-64
RADIATOR PRESSURE CAP - OPERATION . . 7-64
RADIO - DESCRIPTION................8A-10
RADIO - DIAGNOSIS AND TESTING......8A-10
RADIO - INSTALLATION...............8A-11
RADIO - OPERATION..................8A-10
RADIO - REMOVAL...................8A-11
RADIO CHOKE RELAY - DESCRIPTION.....8A-7
RADIO CHOKE RELAY - DIAGNOSIS AND
TESTING............................8A-8
RADIO CHOKE RELAY - INSTALLATION....8A-9
RADIO CHOKE RELAY - OPERATION.......8A-8
RADIO CHOKE RELAY - REMOVAL........8A-8
RADIO NOISE SUPPRESSION
COMPONENTS - DESCRIPTION..........8A-12
RADIO NOISE SUPPRESSION
COMPONENTS - DIAGNOSIS AND
TESTING...........................8A-12
RATINGS, SPECIFICATIONS -
GENERATOR........................8F-26
RBI - REAR AXLE, 286................3-120
RE TRANSMISSION, SPECIAL TOOLS . . . 21-146,
21-316
READING LAMP - DESCRIPTION.........8L-36
READING LAMP - INSTALLATION........8L-37
READING LAMP - OPERATION..........8L-36
READING LAMP - REMOVAL............8L-36
REAR - DESCRIPTION..................2-25
REAR - DESCRIPTION, CRANKSHAFT OIL
SEAL...............................9-33
REAR - INSTALLATION.........5-14,5-22,5-25
REAR - INSTALLATION................22-12
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL...................9-162,9-34,9-90
REAR - INSTALLATION, PROPELLER
SHAFT...............................3-7
REAR - OPERATION, CRANKSHAFT OIL
SEAL...............................9-33
REAR - REMOVAL.............5-10,5-21,5-23
REAR - REMOVAL, CRANKSHAFT OIL
SEAL......................9-161,9-33,9-90
REAR - REMOVAL, PROPELLER SHAFT.....3-7
REAR AXLE - 248RBI - ADJUSTMENTS....3-51
REAR AXLE - 248RBI - DESCRIPTION.....3-46
REAR AXLE - 248RBI - INSTALLATION.....3-51
REAR AXLE - 248RBI - OPERATION.......3-46
REAR AXLE - 248RBI - REMOVAL........3-51
REAR AXLE - 267RBI - ADJUSTMENTS....3-83
REAR AXLE - 267RBI - DESCRIPTION.....3-78
REAR AXLE - 267RBI - INSTALLATION.....3-82
REAR AXLE - 267RBI - OPERATION.......3-78
REAR AXLE - 267RBI - REMOVAL........3-82
REAR AXLE - 286RBI - ADJUSTMENTS
. . . 3-112
REAR AXLE - 286RBI - DESCRIPTION
....3-107
REAR AXLE - 286RBI - INSTALLATION
....3-112
REAR AXLE - 286RBI - OPERATION
......3-108
REAR AXLE - 286RBI - REMOVAL
.......3-112
24 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page

THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-53
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-54
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-51
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-48,7-51,7-53
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM.......21-114,21-286
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-9
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . . 9-11,9-122,9-66
THROTTLE BODY - DESCRIPTION........14-47
THROTTLE BODY - OPERATION.........14-47
THROTTLE CONTROL CABLE -
INSTALLATION.................14-110,14-50
THROTTLE CONTROL CABLE -
REMOVAL....................14-109,14-49
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-50
THROTTLE POSITION SENSOR -
OPERATION.........................14-50
THROTTLE VALVE CABLE -
ADJUSTMENTS, TRANSMISSION . 21-210,21-382
THROTTLE VALVE CABLE -
DESCRIPTION................21-209,21-381
TIMER MODULE - DESCRIPTION,
CENTRAL............................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL....................8E-4
TIMER MODULE - INSTALLATION,
CENTRAL............................8E-6
TIMER MODULE - OPERATION, CENTRAL . . 8E-3
TIMER MODULE - REMOVAL, CENTRAL....8E-5
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-70
TIMING BELT / CHAIN COVER(S) -
INSTALLATION...................9-110,9-54
TIMING BELT / CHAIN COVER(S) -
REMOVAL......................9-110,9-53
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION...................9-111,9-55
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL......................9-111,9-54
TIMING CHAIN STRETCH - INSPECTION,
MEASURING....................9-111,9-54
TIMING, SPECIFICATIONS - IGNITION......8I-4
TIMING VERIFICATION - STANDARD
PROCEDURE........................9-187
TIRE - DESCRIPTION, SPARE...........22-10
TIRE - TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-9
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-7
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS
......................22-9
TIRE ROTATION - STANDARD
PROCEDURE
.........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING
........................22-8
TIRES - DESCRIPTION
.................22-6
TIRES - DESCRIPTION, RADIAL-PLY
.......22-6
TIRES - DESCRIPTION, REPLACEMENT
....22-7
TOOL, SPECIAL TOOLS - OVERHEAD
CONSOLE SPECIAL
...................8M-9
TOOLS - 5.9L DIESEL ENGINE, SPECIAL
. . 9-128
TOOLS - 5.9L ENGINE, SPECIAL
..........9-18
TOOLS - 8.0L ENGINE, SPECIAL
..........9-72
TOOLS - AUDIO SYSTEMS, SPECIAL
......8A-4
TOOLS - BASE BRAKES, SPECIAL
.........5-4
TOOLS - COOLING, SPECIAL
.............7-18TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-63
TOOLS - FRONT AXLE, SPECIAL..........3-27
TOOLS - FUEL SYSTEM, SPECIAL . . . 14-35,14-4
TOOLS - HEADLAMP ALIGNMENT,
SPECIAL............................8L-4
TOOLS - INDEPENDENT FRONT
SUSPENSION, SPECIAL..................2-9
TOOLS - LINK/COIL SUSPENSION,
SPECIAL............................2-16
TOOLS - OVERHEAD CONSOLE SPECIAL
TOOL, SPECIAL......................8M-9
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-22
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-38
TOOLS - PROPELLER SHAFT, SPECIAL......3-6
TOOLS - RE TRANSMISSION, SPECIAL . . 21-146,
21-316
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-41,
19-44
TOOLS - SUSPENSION-REAR, SPECIAL....2-27
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-9
TOOLS, AIRBAG SYSTEM - SPECIAL......8O-6
TOOLS, SPECIFICATIONS - SPECIAL.......8F-7
TOP COVER - INSTALLATION,
INSTRUMENT PANEL.................23-113
TOP COVER - REMOVAL, INSTRUMENT
PANEL............................23-113
TOW HOOK - INSTALLATION, FRONT.....13-10
TOW HOOK - REMOVAL, FRONT.........13-10
TOWING - STANDARD PROCEDURE.......0-10
TRACK - DESCRIPTION, POWER SEAT....8N-21
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-22
TRACK - INSTALLATION, EASY ENTRY
SEAT .............................23-143
TRACK - INSTALLATION, POWER SEAT . . . 8N-22
TRACK - INSTALLATION, SEAT.........23-141
TRACK - OPERATION, POWER SEAT.....8N-22
TRACK - REMOVAL, EASY ENTRY SEAT . . 23-143
TRACK - REMOVAL, POWER SEAT.......8N-22
TRACK - REMOVAL, SEAT.............23-141
TRACK - SPLIT BENCH - INSTALLATION,
SEAT .............................23-142
TRACK - SPLIT BENCH - REMOVAL,
SEAT .............................23-142
TRACK ADJUSTER - INSTALLATION,
SEAT .............................23-143
TRACK ADJUSTER - REMOVAL, SEAT....23-143
TRACK BAR - DIAGNOSIS AND TESTING . . . 2-24
TRACK BAR - INSTALLATION............2-24
TRACK BAR - REMOVAL................2-24
TRAC-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-129,
3-70
TRAC-LOK - DISASSEMBLY,
DIFFERENTIAL...................3-128,3-68
TRAC-LOKT- DIAGNOSIS AND TESTING . . 3-128,
3-67
TRAILER HITCH - INSTALLATION........13-11
TRAILER HITCH - REMOVAL............13-11
TRANS. - INSTALLATION, DIESEL WITH
AUTO..........................8P-12,8P-6
TRANS. - REMOVAL, DIESEL WITH AUTO
. . 8P-5,
8P-9
TRANS COOLER - 5.9L - DESCRIPTION
....7-78
TRANS COOLER - 5.9L - OPERATION
......7-78
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION
........................7-84
TRANS COOLER - 5.9L DIESEL -
OPERATION
..........................7-84
TRANS COOLER - 8.0L - DESCRIPTION
....7-81
TRANS COOLER - 8.0L - OPERATION
......7-81
TRANS OVERTEMP INDICATOR -
DESCRIPTION
.......................8J-31
TRANS OVERTEMP INDICATOR -
OPERATION
.........................8J-31
TRANSFER CASE - DIAGNOSIS AND
TESTING
....................21-431,21-467
TRANSFER CASE - NV241 -
DESCRIPTION
.........................0-5
TRANSFER CASE - NV241HD -
ASSEMBLY
.........................21-480
TRANSFER CASE - NV241HD -
CLEANING
.........................21-476TRANSFER CASE - NV241HD -
DESCRIPTION......................21-465
TRANSFER CASE - NV241HD -
DISASSEMBLY......................21-469
TRANSFER CASE - NV241HD -
INSPECTION.......................21-476
TRANSFER CASE - NV241HD -
INSTALLATION......................21-494
TRANSFER CASE - NV241HD -
OPERATION........................21-467
TRANSFER CASE - NV241HD - REMOVAL . 21-469
TRANSFER CASE - NV241LD -
ASSEMBLY.........................21-445
TRANSFER CASE - NV241LD - CLEANING . 21-441
TRANSFER CASE - NV241LD -
DESCRIPTION......................21-430
TRANSFER CASE - NV241LD -
DISASSEMBLY......................21-432
TRANSFER CASE - NV241LD -
INSPECTION.......................21-442
TRANSFER CASE - NV241LD -
INSTALLATION......................21-458
TRANSFER CASE - NV241LD -
OPERATION........................21-430
TRANSFER CASE - NV241LD - REMOVAL . 21-432
TRANSFER CASE, NV241HD...........21-495
TRANSFER CASE, NV241LD...........21-459
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-11
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-11
TRANSFER CASE, SPECIFICATIONS . 21-458,21-495
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-83
TRANSFER PUMP - INSTALLATION, FUEL . 14-87
TRANSFER PUMP - OPERATION, FUEL....14-83
TRANSFER PUMP - REMOVAL, FUEL.....14-86
TRANSFER PUMP PRESSURE -
DIAGNOSIS AND TESTING, FUEL........14-84
TRANSMISSION - 46RE - DESCRIPTION,
AUTOMATIC.........................21-89
TRANSMISSION - 46RE - OPERATION,
AUTOMATIC.........................21-91
TRANSMISSION - 47RE - DESCRIPTION,
AUTOMATIC........................21-261
TRANSMISSION - 47RE - OPERATION,
AUTOMATIC........................21-263
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-5
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC...........21-268,21-96
TRANSMISSION - INSTALLATION, SHIFT
BOOT - MANUAL....................23-122
TRANSMISSION - REMOVAL, SHIFT
BOOT - MANUAL....................23-122
TRANSMISSION CLUTCH AND BAND
OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING.........21-100,21-272
TRANSMISSION FILL - STANDARD
PROCEDURE
.................21-160,21-330
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC
...........................0-6
TRANSMISSION FLUID - OPERATION,
AUTOMATIC
...........................0-6
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR IN-TANK
...........7-78,7-82,7-84
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITHOUT
RADIATOR IN-TANK
...........7-79,7-82,7-85
TRANSMISSION, SPECIAL TOOLS - RE
. . 21-146,
21-316
TRANSMISSION, SPECIFICATIONS
......21-144,
21-314
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION
...............21-218,21-390
TRANSMISSION TEMPERATURE SENSOR
- OPERATION
.................21-218,21-390
TRANSMISSION THROTTLE VALVE
CABLE - ADJUSTMENTS
........21-210,21-382
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY
......................8N-7
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY
......8N-8
TRANSMITTER - OPERATION, REMOTE
KEYLESS ENTRY
......................8N-8
32 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page