2002 DODGE RAM coolant temperature

²If the MIL is ON and any other emissions DTC
was set (not an OBD II monitor), a good trip occurs
when the Oxygen Sensor Monitor and Catalyst Mon-
itor have been completed, or two minutes of engine
run time if the Oxygen Sensor Monitor and Catalyst
Monitor have been stopped from running.
Fuel System Good Trip
To count a good trip (three required) and turn off
the MIL, the following conditions must occur:
²Engine in closed loop
²Operating in Similar Conditions Window
²Short Term multiplied by Long Term less than
threshold
²Less than threshold for a predetermined time
If all of the previous criteria are met, the PCM will
count a good trip (three required) and turn off the MIL.
Misfire Good Trip
If the following conditions are met the PCM will
count one good trip (three required) in order to turn
off the MIL:
²Operating in Similar Condition Window
²1000 engine revolutions with no misfire
Warm-Up Cycles
Once the MIL has been extinguished by the Good Trip
Counter, the PCM automatically switches to a Warm-Up
Cycle Counter that can be viewed on the DRB III.
Warm-Up Cycles are used to erase DTCs and Freeze
Frames. Forty Warm-Up cycles must occur in order for
the PCM to self-erase a DTC and Freeze Frame. A
Warm-Up Cycle is defined as follows:
²Engine coolant temperature must start below
and rise above 160É F
²Engine coolant temperature must rise by 40É F
²No further faults occur
Freeze Frame Data Storage
Once a failure occurs, the Task Manager records
several engine operating conditions and stores it in a
Freeze Frame. The Freeze Frame is considered one
frame of information taken by an on-board data
recorder. When a fault occurs, the PCM stores the
input data from various sensors so that technicians
can determine under what vehicle operating condi-
tions the failure occurred.
The data stored in Freeze Frame is usually
recorded when a system fails the first time for two
trip faults. Freeze Frame data will only be overwrit-
ten by a different fault with a higher priority.
CAUTION: Erasing DTCs, either with the DRB III or
by disconnecting the battery, also clears all Freeze
Frame data.
Similar Conditions Window
The Similar Conditions Window displays informa-
tion about engine operation during a monitor. Abso-lute MAP (engine load) and Engine RPM are stored
in this window when a failure occurs. There are two
different Similar conditions Windows: Fuel System
and Misfire.
FUEL SYSTEM
²Fuel System Similar Conditions WindowÐ
An indicator that 'Absolute MAP When Fuel Sys Fail'
and 'RPM When Fuel Sys Failed' are all in the same
range when the failure occurred. Indicated by switch-
ing from 'NO' to 'YES'.
²Absolute MAP When Fuel Sys FailÐ The
stored MAP reading at the time of failure. Informs
the user at what engine load the failure occurred.
²Absolute MAPÐ A live reading of engine load
to aid the user in accessing the Similar Conditions
Window.
²RPM When Fuel Sys FailÐ The stored RPM
reading at the time of failure. Informs the user at
what engine RPM the failure occurred.
²Engine RPMÐ A live reading of engine RPM
to aid the user in accessing the Similar Conditions
Window.
²Adaptive Memory FactorÐ The PCM utilizes
both Short Term Compensation and Long Term Adap-
tive to calculate the Adaptive Memory Factor for
total fuel correction.
²Upstream O2S VoltsÐ A live reading of the
Oxygen Sensor to indicate its performance. For
example, stuck lean, stuck rich, etc.
²SCW Time in Window (Similar Conditions
Window Time in Window)Ð A timer used by the
PCM that indicates that, after all Similar Conditions
have been met, if there has been enough good engine
running time in the SCW without failure detected.
This timer is used to increment a Good Trip.
²Fuel System Good Trip CounterÐATrip
Counter used to turn OFF the MIL for Fuel System
DTCs. To increment a Fuel System Good Trip, the
engine must be in the Similar Conditions Window,
Adaptive Memory Factor must be less than cali-
brated threshold and the Adaptive Memory Factor
must stay below that threshold for a calibrated
amount of time.
²Test Done This TripÐ Indicates that the
monitor has already been run and completed during
the current trip.
MISFIRE
²Same Misfire Warm-Up StateÐ Indicates if
the misfire occurred when the engine was warmed up
(above 160É F).
²In Similar Misfire WindowÐ An indicator
that 'Absolute MAP When Misfire Occurred' and
'RPM When Misfire Occurred' are all in the same
range when the failure occurred. Indicated by switch-
ing from 'NO' to 'YES'.
BR/BEEMISSIONS CONTROL 25 - 23
EMISSIONS CONTROL (Continued)

directly, but may cause an engine misfire. This in
turn may cause the ECM to set a DTC for an engine
misfire. Or, a dirty or plugged air filter will not set a
DTC directly, but may cause lack of turbocharger
boost. This in turn may cause the ECM to set a DTC
for a boost pressure malfunction.
FUEL PRESSURE
Primary fuel pressure from the fuel tank to the
fuel injection pump is supplied by the low-pressure
fuel transfer pump. High-pressure to the fuel injec-
tors is supplied by the fuel injection pump. The ECM
cannot detect actual fuel pressure, a clogged fuel fil-
ter, clogged fuel screen, or a pinched fuel supply or
return line. However, a DTC may be set due to an
engine misfire.
CYLINDER COMPRESSION
The ECM cannot detect uneven, low, or high
engine cylinder compression. However, these could
result in a possible misfire which may set a DTC.
EXHAUST SYSTEM
The ECM cannot detect a plugged, restricted or
leaking exhaust system. However, DTC's may be set
for engine misfire, high intake manifold temperature,
high engine coolant temperature, turbocharger over-
boost or turbocharger underboost.
FUEL INJECTOR MECHANICAL MALFUNCTIONS
The ECM cannot determine if a fuel injector is
clogged, the needle is sticking or if the wrong injectoris installed. However, these could result in a possible
misfire which may set a DTC.
EXCESSIVE OIL CONSUMPTION
The ECM cannot determine excessive oil consump-
tion. However, if excess oil consumption is high
enough, it could result in a possible engine misfire
which may set a DTC.
AIR FLOW
The ECM cannot detect a clogged, restricted or
dirty air filter element, or a restriction in the air
inlet system. However, these could result in a possi-
ble misfire which may set a DTC.
AIR PRESSURE LEAKS
The ECM cannot detect leaks or restrictions in the
air intake system. However, these could cause the
ECM to store a Manifold Air Pressure (MAP) sensor
DTC (boost pressure problem detected).
PCM/ECM SYSTEM GROUNDS
The PCM/ECM cannot directly determine poor sys-
tem grounds. However, one or more DTC's may be
generated as a result of poor grounds.
PCM/ECM CONNECTOR ENGAGEMENT
The PCM/ECM may not be able to determine
spread, damaged or corroded connector pins. How-
ever, it might store DTC's as a result of spread con-
nector pins (circuits that are open).
BR/BEEMISSIONS CONTROL 25 - 25
EMISSIONS CONTROL (Continued)

SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS.....9-10,9-122,9-66
SEALS - INSTALLATION, AXLE SHAFT.....3-31
SEALS - REMOVAL, AXLE SHAFT.........3-31
SEALS - REMOVAL, VALVE STEM.........9-82
SEAT - BENCH SEAT - INSTALLATION....23-133
SEAT - BENCH SEAT - REMOVAL.......23-133
SEAT - INSTALLATION, REAR..........23-144
SEAT - INSTALLATION, SEAT - BENCH . . . 23-133
SEAT - INSTALLATION, SEAT BACK -
BENCH............................23-135
SEAT - REMOVAL, REAR..............23-144
SEAT - REMOVAL, SEAT - BENCH.......23-133
SEAT - REMOVAL, SEAT BACK - BENCH . . 23-135
SEAT - SPLIT BENCH - INSTALLATION . . . 23-134
SEAT - SPLIT BENCH - REMOVAL.......23-133
SEAT ARMREST/CONSOLE -
INSTALLATION, CENTER..............23-132
SEAT ARMREST/CONSOLE - REMOVAL,
CENTER...........................23-132
SEAT ARMREST/LATCH COVER -
INSTALLATION, CENTER..............23-132
SEAT ARMREST/LATCH COVER -
REMOVAL, CENTER..................23-132
SEAT BACK - BENCH SEAT -
INSTALLATION......................23-135
SEAT BACK - BENCH SEAT - REMOVAL . . 23-135
SEAT BACK - SPLIT BENCH -
INSTALLATION......................23-136
SEAT BACK - SPLIT BENCH - REMOVAL . . 23-135
SEAT BACK COVER - INSTALLATION.....23-137
SEAT BACK COVER - REMOVAL........23-137
SEAT BACK COVER - SPLIT BENCH -
INSTALLATION......................23-137
SEAT BACK COVER - SPLIT BENCH -
REMOVAL.........................23-137
SEAT BACK RECLINER - INSTALLATION . . 23-138
SEAT BACK RECLINER - REMOVAL......23-138
SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-26
SEAT BELT & RETRACTOR - REMOVAL,
REAR..............................8O-26
SEAT BELT BUCKLE - INSTALLATION,
FRONT.............................8O-20
SEAT BELT BUCKLE - INSTALLATION,
REAR..............................8O-27
SEAT BELT BUCKLE - REMOVAL, FRONT . . 8O-20
SEAT BELT BUCKLE - REMOVAL, REAR . . . 8O-27
SEAT BELT SWITCH - DESCRIPTION.....8O-28
SEAT BELT SWITCH - DIAGNOSIS AND
TESTING...........................8O-28
SEAT BELT SWITCH - OPERATION.......8O-28
SEAT BELT TURNING LOOP ADJUSTER -
INSTALLATION......................8O-29
SEAT BELT TURNING LOOP ADJUSTER -
REMOVAL..........................8O-29
SEAT CUSHION - INSTALLATION........23-138
SEAT CUSHION - REMOVAL...........23-138
SEAT CUSHION COVER - INSTALLATION . 23-139
SEAT CUSHION COVER - REMOVAL.....23-139
SEAT CUSHION COVER - SPLIT BENCH -
INSTALLATION......................23-140
SEAT CUSHION COVER - SPLIT BENCH -
REMOVAL.........................23-139
SEAT ELEMENT - DESCRIPTION, HEATED . 8G-10
SEAT ELEMENT - INSTALLATION,
HEATED............................8G-13
SEAT ELEMENT - OPERATION, HEATED . . . 8G-11
SEAT ELEMENT - REMOVAL, HEATED....8G-13
SEAT ELEMENT AND SENSOR -
DIAGNOSIS AND TESTING, HEATED......8G-11
SEAT HEATER SWITCH - DESCRIPTION,
DRIVER.............................8G-7
SEAT HEATER SWITCH - DESCRIPTION,
PASSENGER........................8G-16
SEAT HEATER SWITCH - INSTALLATION,
DRIVER............................8G-10
SEAT HEATER SWITCH - INSTALLATION,
PASSENGER........................8G-19
SEAT HEATER SWITCH - OPERATION,
DRIVER
.............................8G-8
SEAT HEATER SWITCH - OPERATION,
PASSENGER
........................8G-17
SEAT HEATER SWITCH - REMOVAL,
DRIVER
.............................8G-9
SEAT HEATER SWITCH - REMOVAL,
PASSENGER
........................8G-18
SEAT MODULE - DESCRIPTION, HEATED
. . 8E-20SEAT MODULE - DIAGNOSIS AND
TESTING, HEATED....................8E-21
SEAT MODULE - INSTALLATION, HEATED . . 8E-23
SEAT MODULE - OPERATION, HEATED....8E-20
SEAT MODULE - REMOVAL, HEATED.....8E-23
SEAT RELAY - DESCRIPTION, HEATED....8G-14
SEAT RELAY - DIAGNOSIS AND
TESTING, HEATED....................8G-15
SEAT RELAY - INSTALLATION, HEATED . . . 8G-16
SEAT RELAY - OPERATION, HEATED.....8G-15
SEAT RELAY - REMOVAL, HEATED.......8G-16
SEAT RISER - INSTALLATION..........23-141
SEAT RISER - REMOVAL..............23-141
SEAT SWITCH - DESCRIPTION, DRIVER
POWER............................8N-17
SEAT SWITCH - DESCRIPTION,
PASSENGER POWER..................8N-20
SEAT SWITCH - DIAGNOSIS AND
TESTING, DRIVER POWER.............8N-17
SEAT SWITCH - DIAGNOSIS AND
TESTING, HEATED...............8G-17,8G-8
SEAT SWITCH - DIAGNOSIS AND
TESTING, PASSENGER POWER.........8N-20
SEAT SWITCH - INSTALLATION, DRIVER
POWER............................8N-18
SEAT SWITCH - INSTALLATION,
PASSENGER POWER..................8N-21
SEAT SWITCH - OPERATION, DRIVER
POWER............................8N-17
SEAT SWITCH - OPERATION,
PASSENGER POWER...................8N-20
SEAT SWITCH - REMOVAL, DRIVER
POWER............................8N-18
SEAT SWITCH - REMOVAL, PASSENGER
POWER............................8N-21
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-5
SEAT SYSTEM - DESCRIPTION, POWER . . 8N-16
SEAT SYSTEM - DIAGNOSIS AND
TESTING, HEATED.....................8G-6
SEAT SYSTEM - DIAGNOSIS AND
TESTING, POWER....................8N-16
SEAT SYSTEM - OPERATION, HEATED.....8G-6
SEAT SYSTEM - OPERATION, POWER....8N-16
SEAT TRACK - DESCRIPTION, POWER....8N-21
SEAT TRACK - DIAGNOSIS AND
TESTING, POWER....................8N-22
SEAT TRACK - INSTALLATION..........23-141
SEAT TRACK - INSTALLATION, EASY
ENTRY............................23-143
SEAT TRACK - INSTALLATION, POWER . . . 8N-22
SEAT TRACK - OPERATION, POWER.....8N-22
SEAT TRACK - REMOVAL.............23-141
SEAT TRACK - REMOVAL, EASY ENTRY . . 23-143
SEAT TRACK - REMOVAL, POWER.......8N-22
SEAT TRACK - SPLIT BENCH -
INSTALLATION......................23-142
SEAT TRACK - SPLIT BENCH - REMOVAL . 23-142
SEAT TRACK ADJUSTER - INSTALLATION . 23-143
SEAT TRACK ADJUSTER - REMOVAL....23-143
SEATBELT INDICATOR - DESCRIPTION....8J-27
SEATBELT INDICATOR - OPERATION......8J-27
SEATS - CLEANING, INTAKE/EXHAUST
VALVES .............................9-26
SEATS - DESCRIPTION...............23-131
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES............9-138,9-23,9-80
SEATS - INSPECTION, INTAKE/EXHAUST
VALVES .............................9-26
SEATS - INSTALLATION, INTAKE/
EXHAUST VALVES.....................9-26
SEATS - OPERATION.................23-131
SEATS - REMOVAL, INTAKE/EXHAUST
VALVES .............................9-25
SECOND WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-154
SECOND WEATHERSTRIP - REMOVAL,
FRONT DOOR......................23-154
SECTION IDENTIFICATION AND
INFORMATION - DESCRIPTION........8W-01-6
SECURITY - DESCRIPTION, VEHICLE
THEFT
..............................8Q-1
SECURITY - OPERATION, VEHICLE THEFT
. . 8Q-2
SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT
..............8Q-3
SELECTION - ADDITIVES - STANDARD
PROCEDURE, COOLANT
................7-17
SELECTOR INDICATOR - DESCRIPTION,
GEAR
..............................8J-20SELECTOR INDICATOR - OPERATION,
GEAR..............................8J-21
SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL GAUGE.................14-7
SENDING UNIT / SENSOR -
DESCRIPTION, FUEL LEVEL........14-7,14-77
SENDING UNIT / SENSOR -
INSTALLATION, FUEL LEVEL.............14-8
SENDING UNIT / SENSOR - OPERATION,
FUEL LEVEL.....................14-7,14-77
SENDING UNIT / SENSOR - REMOVAL,
FUEL LEVEL..........................14-7
SENSE - DESCRIPTION, IGNITION
CIRCUIT............................8E-17
SENSE - OPERATION, IGNITION CIRCUIT . . 8E-19
SENSE - PCM INPUT - OPERATION, ASD . . . 8I-4
SENSITIVE DEVICES - STANDARD
PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD).................8W-01-8
SENSOR - 5.9L - DESCRIPTION, ENGINE
COOLANT TEMP......................7-47
SENSOR - 5.9L - INSTALLATION, ENGINE
COOLANT TEMP......................7-47
SENSOR - 5.9L - OPERATION, ENGINE
COOLANT TEMP......................7-47
SENSOR - 5.9L - REMOVAL, ENGINE
COOLANT TEMP......................7-47
SENSOR - DESCRIPTION, ACCELERATOR
PEDAL POSITION....................14-95
SENSOR - DESCRIPTION, AMBIENT
TEMP.............................8M-12
SENSOR - DESCRIPTION, BATTERY
TEMPERATURE......................8F-27
SENSOR - DESCRIPTION, FRONT WHEEL
SPEED..............................5-38
SENSOR - DESCRIPTION, FUEL LEVEL
SENDING UNIT..................14-7,14-77
SENSOR - DESCRIPTION, FUEL
TEMPERATURE.....................14-104
SENSOR - DESCRIPTION, O2...........14-45
SENSOR - DESCRIPTION, SPEED . 21-209,21-381
SENSOR - DESCRIPTION, THROTTLE
POSITION..........................14-50
SENSOR - DESCRIPTION,
TRANSMISSION TEMPERATURE . . 21-218,21-390
SENSOR - DESCRIPTION, WATER IN
FUEL..............................14-89
SENSOR - DIAGNOSIS AND TESTING,
AMBIENT TEMPERATURE..............8M-12
SENSOR - DIAGNOSIS AND TESTING,
HEATED SEAT ELEMENT...............8G-11
SENSOR - DIAGNOSIS AND TESTING,
REAR WHEEL SPEED..................5-40
SENSOR - INSTALLATION,
ACCELERATOR PEDAL POSITION........14-97
SENSOR - INSTALLATION, AMBIENT
TEMP.............................8M-13
SENSOR - INSTALLATION, BATTERY
TEMPERATURE......................8F-28
SENSOR - INSTALLATION, FUEL LEVEL
SENDING UNIT.......................14-8
SENSOR - INSTALLATION, MAP........14-108
SENSOR - INSTALLATION, O2...........14-47
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-40
SENSOR - OPERATION, ACCELERATOR
PEDAL POSITION....................14-95
SENSOR - OPERATION, AMBIENT TEMP . . 8M-12
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-27
SENSOR - OPERATION, FRONT WHEEL
SPEED..............................5-38
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT..................14-7,14-77
SENSOR - OPERATION, FUEL
TEMPERATURE.....................14-104
SENSOR - OPERATION, O2.............14-45
SENSOR - OPERATION, SPEED . . . 21-209,21-381
SENSOR - OPERATION, THROTTLE
POSITION..........................14-50
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE
...............21-218,21-390
SENSOR - OPERATION, WATER IN FUEL
. . 14-89
SENSOR - REMOVAL, ACCELERATOR
PEDAL POSITION
....................14-95
SENSOR - REMOVAL, AMBIENT TEMP
. . . 8M-12
SENSOR - REMOVAL, BATTERY
TEMPERATURE
......................8F-27
BR/BEINDEX 27
Description Group-Page Description Group-Page Description Group-Page

SYSTEM - DIAGNOSIS AND TESTING,
POWER LOCK & REMOTE KEYLESS
ENTRY..............................8N-5
SYSTEM - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-16
SYSTEM - DIAGNOSIS AND TESTING,
POWER STEERING....................19-2
SYSTEM - DIAGNOSIS AND TESTING,
STARTING..........................8F-32
SYSTEM - DIAGNOSIS AND TESTING,
TURN SIGNAL & HAZARD WARNING......8L-3
SYSTEM - DIAGNOSIS AND TESTING,
VACUUM...........................24-10
SYSTEM - DIAGNOSIS AND TESTING,
VEHICLE THEFT SECURITY..............8Q-3
SYSTEM - DIAGNOSIS AND TESTING,
WIPER & WASHER....................8R-3
SYSTEM - INSPECTION, BATTERY........8F-6
SYSTEM - INSPECTION, WIPER &
WASHER............................8R-6
SYSTEM - LEAKS - DIAGNOSIS AND
TESTING, CHARGE AIR COOLER.........11-18
SYSTEM - OPERATION, AIR INJECTION . . . 25-28
SYSTEM - OPERATION, BATTERY.........8F-2
SYSTEM - OPERATION, CHIME
WARNING...........................8B-1
SYSTEM - OPERATION, COOLING..........7-4
SYSTEM - OPERATION, FUEL DELIVERY . . . 14-2
SYSTEM - OPERATION, HEATED MIRROR . . 8G-2
SYSTEM - OPERATION, HEATED SEAT.....8G-6
SYSTEM - OPERATION, INSTRUMENT
PANEL..............................23-106
SYSTEM - OPERATION, POWER SEAT....8N-16
SYSTEM - OPERATION, REMOTE
KEYLESS ENTRY......................8N-4
SYSTEM - OPERATION, SPEED CONTROL . . 8P-2
SYSTEM - OPERATION, TURN SIGNAL &
HAZARD WARNING....................8L-2
SYSTEM - SPECIAL TOOLS, AIRBAG......8O-6
SYSTEM - SPECIFICATIONS, TORQUE -
GENERATOR/CHARGING...............8F-27
SYSTEM - SPECIFICATIONS, TORQUE -
STARTING..........................8F-37
SYSTEM - STANDARD PROCEDURE,
BLEEDING ABS BRAKE.................5-36
SYSTEM - STANDARD PROCEDURE,
FLUSHING POWER STEERING...........19-34
SYSTEM - TORQUE, AIR INJECTION......25-29
SYSTEM - TORQUE, EVAP..............25-32
SYSTEM - TORQUE, SPEED CONTROL.....8P-4
SYSTEM 5.9L DIESEL ENGINE -
STANDARD PROCEDURE, DRAINING
COOLING............................7-15
SYSTEM 5.9L DIESEL ENGINE -
STANDARD PROCEDURE, REFILLING
COOLING............................7-16
SYSTEM 5.9L/8.0L ENGINES -
STANDARD PROCEDURE, DRAINING
COOLING............................7-15
SYSTEM 5.9L/8.0L ENGINES -
STANDARD PROCEDURE, REFILLING
COOLING............................7-16
SYSTEM AIR LEAK VACUUM TEST -
DIAGNOSIS AND TESTING, FUEL........14-57
SYSTEM AIRFLOW - DESCRIPTION,
HVAC..............................24-30
SYSTEM CHARGE - STANDARD
PROCEDURE, REFRIGERANT............24-46
SYSTEM CLEANING/REVERSE FLUSHING
- STANDARD PROCEDURE, COOLING......7-17
SYSTEM DIESEL ENGINE - DIAGNOSIS
AND TESTING, COOLING................7-13
SYSTEM EVACUATE - STANDARD
PROCEDURE, REFRIGERANT............24-46
SYSTEM FLOW - 5.9L DIESEL -
DESCRIPTION, COOLING.................7-2
SYSTEM FLOW - 5.9L ENGINE -
DESCRIPTION, COOLING.................7-1
SYSTEM GAS ENGINE - DIAGNOSIS AND
TESTING, COOLING
.....................7-7
SYSTEM LEAKS - DIAGNOSIS AND
TESTING, COOLING
.....................7-5
SYSTEM LEAKS - DIAGNOSIS AND
TESTING, REFRIGERANT
...............24-43
SYSTEM PARTS - STANDARD
PROCEDURES, CLEANING FUEL
.........14-61
SYSTEM PRESSURE - GAS ENGINES -
SPECIFICATIONS, FUEL
.................14-3SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE, FUEL..........14-3
SYSTEM PRESSURES, DIESEL ENGINES
- FUEL.............................14-62
SYSTEM REQUIREMENTS -
DESCRIPTION, COOLING................24-1
SYSTEM SERVICE EQUIPMENT -
STANDARD PROCEDURE,
REFRIGERANT.......................24-45
SYSTEM SERVICE PORT - DESCRIPTION,
REFRIGERANT........................24-1
SYSTEM SERVICE PORT - OPERATION,
REFRIGERANT........................24-2
SYSTEM, SPECIAL TOOLS - DIESEL
FUEL..............................14-63
SYSTEM, SPECIAL TOOLS - FUEL . . . 14-35,14-4
SYSTEM, SPECIFICATIONS - STARTING . . . 8F-36
SYSTEMS - DESCRIPTION, MONITORED . . 25-17
SYSTEMS, SPECIAL TOOLS - AUDIO......8A-4
SYSTEMS, SPECIAL TOOLS - POWER
DISTRIBUTION....................8W-97-2
TABLE, SPECIFICATIONS - A/C
APPLICATION........................24-7
TACHOMETER - DESCRIPTION..........8J-30
TACHOMETER - OPERATION............8J-30
TAIL LAMP - DESCRIPTION............8L-29
TAIL LAMP - INSTALLATION............8L-30
TAIL LAMP - OPERATION..............8L-29
TAIL LAMP - REMOVAL................8L-29
TAIL LAMP UNIT - INSTALLATION.......8L-30
TAIL LAMP UNIT - REMOVAL...........8L-30
TAILGATE - INSTALLATION.............23-67
TAILGATE - REMOVAL.................23-67
TAILPIPE - 3.9L/5.2L/5.9L - INSPECTION . . 11-11
TAILPIPE - 3.9L/5.2L/5.9L -
INSTALLATION.......................11-11
TAILPIPE - 3.9L/5.2L/5.9L - REMOVAL....11-11
TAILPIPE - 5.9L DIESEL - INSPECTION....11-12
TAILPIPE - 5.9L DIESEL - INSTALLATION . . 11-13
TAILPIPE - 5.9L DIESEL - REMOVAL.....11-12
TAILPIPE - 5.9L HD/8.0L - INSPECTION . . . 11-12
TAILPIPE - 5.9L HD/8.0L -
INSTALLATION.......................11-12
TAILPIPE - 5.9L HD/8.0L - REMOVAL.....11-12
TANK - DESCRIPTION, DIESEL FUEL.....14-82
TANK - DESCRIPTION, FUEL............14-18
TANK - INSTALLATION, FUEL...........14-20
TANK - OPERATION, FUEL..............14-18
TANK - REMOVAL, FUEL...............14-18
TANK CHECK VALVE - DESCRIPTION,
FUEL..............................14-21
TANK CHECK VALVE - INSTALLATION,
FUEL..............................14-23
TANK CHECK VALVE - REMOVAL, FUEL . . . 14-22
TANK MODULE - DESCRIPTION, FUEL....14-82
TANK MODULE - INSTALLATION, FUEL....14-83
TANK MODULE - OPERATION, FUEL......14-82
TANK MODULE - REMOVAL, FUEL.......14-83
TAPE STRIPE - INSTALLATION..........23-89
TAPE STRIPE - REMOVAL..............23-88
TAPPETS - DIAGNOSIS AND TESTING,
HYDRAULIC......................9-36,9-91
TASK MANAGER - DESCRIPTION........25-17
TASK MANAGER - OPERATION..........25-21
TEMP SENSOR - 5.9L - DESCRIPTION,
ENGINE COOLANT.....................7-47
TEMP SENSOR - 5.9L - INSTALLATION,
ENGINE COOLANT.....................7-47
TEMP SENSOR - 5.9L - OPERATION,
ENGINE COOLANT.....................7-47
TEMP SENSOR - 5.9L - REMOVAL,
ENGINE COOLANT.....................7-47
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-12
TEMP SENSOR - INSTALLATION,
AMBIENT..........................8M-13
TEMP SENSOR - OPERATION, AMBIENT . . 8M-12
TEMP SENSOR - REMOVAL, AMBIENT . . . 8M-12
TEMPERATURE GAUGE - DESCRIPTION,
ENGINE
............................8J-18
TEMPERATURE GAUGE - OPERATION,
ENGINE
............................8J-19
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY
...........................8F-27
TEMPERATURE SENSOR - DESCRIPTION,
FUEL
.............................14-104
TEMPERATURE SENSOR - DESCRIPTION,
TRANSMISSION
...............21-218,21-390TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR -
INSTALLATION, BATTERY..............8F-28
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-27
TEMPERATURE SENSOR - OPERATION,
FUEL.............................14-104
TEMPERATURE SENSOR - OPERATION,
TRANSMISSION...............21-218,21-390
TEMPERATURE SENSOR - REMOVAL,
BATTERY...........................8F-27
TEMPORARY - DESCRIPTION, SPARE
TIRE................................22-6
TENSIONERS - 5.9L - DESCRIPTION,
BELT ...............................7-19
TENSIONERS - 5.9L - INSTALLATION,
BELT ...............................7-20
TENSIONERS - 5.9L - OPERATION, BELT . . . 7-19
TENSIONERS - 5.9L - REMOVAL, BELT.....7-19
TENSIONERS - 5.9L DIESEL -
DESCRIPTION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
INSTALLATION, BELT...................7-23
TENSIONERS - 5.9L DIESEL -
OPERATION, BELT.....................7-23
TENSIONERS - 5.9L DIESEL - REMOVAL,
BELT ...............................7-23
TENSIONERS - 8.0L - DESCRIPTION,
BELT ...............................7-20
TENSIONERS - 8.0L - INSTALLATION,
BELT ...............................7-22
TENSIONERS - 8.0L - OPERATION, BELT.....7-21
TENSIONERS - 8.0L - REMOVAL, BELT.....7-21
TERMINAL - INSTALLATION.........8W-01-13
TERMINAL - REMOVAL.............8W-01-13
TEST - DIAGNOSIS AND TESTING, FUEL
INJECTOR..........................14-99
TEST - DIAGNOSIS AND TESTING, FUEL
PRESSURE LEAK DOWN................14-2
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP AMPERAGE....................14-10
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP CAPACITY......................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
PUMP PRESSURE.....................14-9
TEST - DIAGNOSIS AND TESTING, FUEL
SYSTEM AIR LEAK VACUUM............14-57
TEST - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE.........21-270,21-98
TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-4
TEST - DIAGNOSIS AND TESTING,
VACUUM SUPPLY.....................8P-3
TEST - STANDARD PROCEDURE,
BUILT-IN INDICATOR..................8F-10
TEST - STANDARD PROCEDURE,
HYDROMETER.......................8F-11
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE, LOAD . . . 8F-12
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-12
TEST - STANDARD PROCEDURE,
VERIFICATION........................8O-5
TEST MODE - DESCRIPTION, CIRCUIT
ACTUATION
..........................25-2
TEST MODE - DESCRIPTION, STATE
DISPLAY
............................25-1
TETHER - INSTALLATION, CHILD
.........8O-9
TETHER - REMOVAL, CHILD
.............8O-9
THEFT SECURITY - DESCRIPTION,
VEHICLE
............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE
. . 8Q-2
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE
................8Q-3
THERMOSTAT - 5.9L - DESCRIPTION,
ENGINE COOLANT
.....................7-48
THERMOSTAT - 5.9L - INSTALLATION,
ENGINE COOLANT
.....................7-49
THERMOSTAT - 5.9L - OPERATION,
ENGINE COOLANT
.....................7-48
THERMOSTAT - 5.9L - REMOVAL,
ENGINE COOLANT
.....................7-48
THERMOSTAT - 5.9L DIESEL -
DESCRIPTION, ENGINE COOLANT
.........7-53
THERMOSTAT - 5.9L DIESEL -
INSTALLATION, ENGINE COOLANT
........7-54
BR/BEINDEX 31
Description Group-Page Description Group-Page Description Group-Page

THERMOSTAT - 5.9L DIESEL -
OPERATION, ENGINE COOLANT..........7-53
THERMOSTAT - 5.9L DIESEL -
REMOVAL, ENGINE COOLANT............7-54
THERMOSTAT - 8.0L - DESCRIPTION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 8.0L - INSTALLATION,
ENGINE COOLANT.....................7-52
THERMOSTAT - 8.0L - OPERATION,
ENGINE COOLANT.....................7-51
THERMOSTAT - 8.0L - REMOVAL,
ENGINE COOLANT.....................7-51
THERMOSTAT - DIAGNOSIS AND
TESTING....................7-48,7-51,7-53
THREAD REPAIR - STANDARD
PROCEDURE, ALUMINUM.......21-114,21-286
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-9
THREADS - STANDARD PROCEDURE,
REPAIR DAMAGED OR WORN . . 9-11,9-122,9-66
THROTTLE BODY - DESCRIPTION........14-47
THROTTLE BODY - OPERATION.........14-47
THROTTLE CONTROL CABLE -
INSTALLATION.................14-110,14-50
THROTTLE CONTROL CABLE -
REMOVAL....................14-109,14-49
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-50
THROTTLE POSITION SENSOR -
OPERATION.........................14-50
THROTTLE VALVE CABLE -
ADJUSTMENTS, TRANSMISSION . 21-210,21-382
THROTTLE VALVE CABLE -
DESCRIPTION................21-209,21-381
TIMER MODULE - DESCRIPTION,
CENTRAL............................8E-1
TIMER MODULE - DIAGNOSIS AND
TESTING, CENTRAL....................8E-4
TIMER MODULE - INSTALLATION,
CENTRAL............................8E-6
TIMER MODULE - OPERATION, CENTRAL . . 8E-3
TIMER MODULE - REMOVAL, CENTRAL....8E-5
TIMING - DIAGNOSIS AND TESTING,
FUEL INJECTION PUMP...............14-70
TIMING BELT / CHAIN COVER(S) -
INSTALLATION...................9-110,9-54
TIMING BELT / CHAIN COVER(S) -
REMOVAL......................9-110,9-53
TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION...................9-111,9-55
TIMING BELT/CHAIN AND SPROCKETS -
REMOVAL......................9-111,9-54
TIMING CHAIN STRETCH - INSPECTION,
MEASURING....................9-111,9-54
TIMING, SPECIFICATIONS - IGNITION......8I-4
TIMING VERIFICATION - STANDARD
PROCEDURE........................9-187
TIRE - DESCRIPTION, SPARE...........22-10
TIRE - TEMPORARY - DESCRIPTION,
SPARE..............................22-6
TIRE AND WHEEL BALANCE -
STANDARD PROCEDURE................22-4
TIRE AND WHEEL RUNOUT - DIAGNOSIS
AND TESTING........................22-1
TIRE INFLATION PRESSURES -
DESCRIPTION........................22-7
TIRE NOISE OR VIBRATION - DIAGNOSIS
AND TESTING........................22-9
TIRE PRESSURE FOR HIGH SPEEDS -
DESCRIPTION........................22-7
TIRE REVOLUTIONS PER MILE,
SPECIFICATIONS
......................22-9
TIRE ROTATION - STANDARD
PROCEDURE
.........................22-2
TIRE WEAR PATTERNS - DIAGNOSIS
AND TESTING
........................22-8
TIRES - DESCRIPTION
.................22-6
TIRES - DESCRIPTION, RADIAL-PLY
.......22-6
TIRES - DESCRIPTION, REPLACEMENT
....22-7
TOOL, SPECIAL TOOLS - OVERHEAD
CONSOLE SPECIAL
...................8M-9
TOOLS - 5.9L DIESEL ENGINE, SPECIAL
. . 9-128
TOOLS - 5.9L ENGINE, SPECIAL
..........9-18
TOOLS - 8.0L ENGINE, SPECIAL
..........9-72
TOOLS - AUDIO SYSTEMS, SPECIAL
......8A-4
TOOLS - BASE BRAKES, SPECIAL
.........5-4
TOOLS - COOLING, SPECIAL
.............7-18TOOLS - DIESEL FUEL SYSTEM,
SPECIAL...........................14-63
TOOLS - FRONT AXLE, SPECIAL..........3-27
TOOLS - FUEL SYSTEM, SPECIAL . . . 14-35,14-4
TOOLS - HEADLAMP ALIGNMENT,
SPECIAL............................8L-4
TOOLS - INDEPENDENT FRONT
SUSPENSION, SPECIAL..................2-9
TOOLS - LINK/COIL SUSPENSION,
SPECIAL............................2-16
TOOLS - OVERHEAD CONSOLE SPECIAL
TOOL, SPECIAL......................8M-9
TOOLS - POWER DISTRIBUTION
SYSTEMS, SPECIAL................8W-97-2
TOOLS - POWER STEERING GEAR,
SPECIAL...........................19-22
TOOLS - POWER STEERING PUMP,
SPECIAL...........................19-38
TOOLS - PROPELLER SHAFT, SPECIAL......3-6
TOOLS - RE TRANSMISSION, SPECIAL . . 21-146,
21-316
TOOLS - STEERING LINKAGE, SPECIAL . . . 19-41,
19-44
TOOLS - SUSPENSION-REAR, SPECIAL....2-27
TOOLS - WIRING/TERMINAL, SPECIAL . 8W-01-9
TOOLS, AIRBAG SYSTEM - SPECIAL......8O-6
TOOLS, SPECIFICATIONS - SPECIAL.......8F-7
TOP COVER - INSTALLATION,
INSTRUMENT PANEL.................23-113
TOP COVER - REMOVAL, INSTRUMENT
PANEL............................23-113
TOW HOOK - INSTALLATION, FRONT.....13-10
TOW HOOK - REMOVAL, FRONT.........13-10
TOWING - STANDARD PROCEDURE.......0-10
TRACK - DESCRIPTION, POWER SEAT....8N-21
TRACK - DIAGNOSIS AND TESTING,
POWER SEAT.......................8N-22
TRACK - INSTALLATION, EASY ENTRY
SEAT .............................23-143
TRACK - INSTALLATION, POWER SEAT . . . 8N-22
TRACK - INSTALLATION, SEAT.........23-141
TRACK - OPERATION, POWER SEAT.....8N-22
TRACK - REMOVAL, EASY ENTRY SEAT . . 23-143
TRACK - REMOVAL, POWER SEAT.......8N-22
TRACK - REMOVAL, SEAT.............23-141
TRACK - SPLIT BENCH - INSTALLATION,
SEAT .............................23-142
TRACK - SPLIT BENCH - REMOVAL,
SEAT .............................23-142
TRACK ADJUSTER - INSTALLATION,
SEAT .............................23-143
TRACK ADJUSTER - REMOVAL, SEAT....23-143
TRACK BAR - DIAGNOSIS AND TESTING . . . 2-24
TRACK BAR - INSTALLATION............2-24
TRACK BAR - REMOVAL................2-24
TRAC-LOK - ASSEMBLY, DIFFERENTIAL . . . 3-129,
3-70
TRAC-LOK - DISASSEMBLY,
DIFFERENTIAL...................3-128,3-68
TRAC-LOKT- DIAGNOSIS AND TESTING . . 3-128,
3-67
TRAILER HITCH - INSTALLATION........13-11
TRAILER HITCH - REMOVAL............13-11
TRANS. - INSTALLATION, DIESEL WITH
AUTO..........................8P-12,8P-6
TRANS. - REMOVAL, DIESEL WITH AUTO
. . 8P-5,
8P-9
TRANS COOLER - 5.9L - DESCRIPTION
....7-78
TRANS COOLER - 5.9L - OPERATION
......7-78
TRANS COOLER - 5.9L DIESEL -
DESCRIPTION
........................7-84
TRANS COOLER - 5.9L DIESEL -
OPERATION
..........................7-84
TRANS COOLER - 8.0L - DESCRIPTION
....7-81
TRANS COOLER - 8.0L - OPERATION
......7-81
TRANS OVERTEMP INDICATOR -
DESCRIPTION
.......................8J-31
TRANS OVERTEMP INDICATOR -
OPERATION
.........................8J-31
TRANSFER CASE - DIAGNOSIS AND
TESTING
....................21-431,21-467
TRANSFER CASE - NV241 -
DESCRIPTION
.........................0-5
TRANSFER CASE - NV241HD -
ASSEMBLY
.........................21-480
TRANSFER CASE - NV241HD -
CLEANING
.........................21-476TRANSFER CASE - NV241HD -
DESCRIPTION......................21-465
TRANSFER CASE - NV241HD -
DISASSEMBLY......................21-469
TRANSFER CASE - NV241HD -
INSPECTION.......................21-476
TRANSFER CASE - NV241HD -
INSTALLATION......................21-494
TRANSFER CASE - NV241HD -
OPERATION........................21-467
TRANSFER CASE - NV241HD - REMOVAL . 21-469
TRANSFER CASE - NV241LD -
ASSEMBLY.........................21-445
TRANSFER CASE - NV241LD - CLEANING . 21-441
TRANSFER CASE - NV241LD -
DESCRIPTION......................21-430
TRANSFER CASE - NV241LD -
DISASSEMBLY......................21-432
TRANSFER CASE - NV241LD -
INSPECTION.......................21-442
TRANSFER CASE - NV241LD -
INSTALLATION......................21-458
TRANSFER CASE - NV241LD -
OPERATION........................21-430
TRANSFER CASE - NV241LD - REMOVAL . 21-432
TRANSFER CASE, NV241HD...........21-495
TRANSFER CASE, NV241LD...........21-459
TRANSFER CASE SKID PLATE -
INSTALLATION.......................13-11
TRANSFER CASE SKID PLATE -
REMOVAL..........................13-11
TRANSFER CASE, SPECIFICATIONS . 21-458,21-495
TRANSFER PUMP - DESCRIPTION, FUEL . . 14-83
TRANSFER PUMP - INSTALLATION, FUEL . 14-87
TRANSFER PUMP - OPERATION, FUEL....14-83
TRANSFER PUMP - REMOVAL, FUEL.....14-86
TRANSFER PUMP PRESSURE -
DIAGNOSIS AND TESTING, FUEL........14-84
TRANSMISSION - 46RE - DESCRIPTION,
AUTOMATIC.........................21-89
TRANSMISSION - 46RE - OPERATION,
AUTOMATIC.........................21-91
TRANSMISSION - 47RE - DESCRIPTION,
AUTOMATIC........................21-261
TRANSMISSION - 47RE - OPERATION,
AUTOMATIC........................21-263
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-5
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC...........21-268,21-96
TRANSMISSION - INSTALLATION, SHIFT
BOOT - MANUAL....................23-122
TRANSMISSION - REMOVAL, SHIFT
BOOT - MANUAL....................23-122
TRANSMISSION CLUTCH AND BAND
OPERATION - DIAGNOSIS AND
TESTING, AIR TESTING.........21-100,21-272
TRANSMISSION FILL - STANDARD
PROCEDURE
.................21-160,21-330
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC
...........................0-6
TRANSMISSION FLUID - OPERATION,
AUTOMATIC
...........................0-6
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITH
RADIATOR IN-TANK
...........7-78,7-82,7-84
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES - WITHOUT
RADIATOR IN-TANK
...........7-79,7-82,7-85
TRANSMISSION, SPECIAL TOOLS - RE
. . 21-146,
21-316
TRANSMISSION, SPECIFICATIONS
......21-144,
21-314
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION
...............21-218,21-390
TRANSMISSION TEMPERATURE SENSOR
- OPERATION
.................21-218,21-390
TRANSMISSION THROTTLE VALVE
CABLE - ADJUSTMENTS
........21-210,21-382
TRANSMITTER - DESCRIPTION, REMOTE
KEYLESS ENTRY
......................8N-7
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY
......8N-8
TRANSMITTER - OPERATION, REMOTE
KEYLESS ENTRY
......................8N-8
32 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page