2002 CADILLAC ESCALADE EXT Owners Manual

2-111
TRANS HOT...IDLE ENGINE Message
The transmission over-temperature display is contained
in the message center.
If this warning message is
displayed, pull the vehicle
off the roadway when it is
safe to do so.
Set the parking brake and place the transmission in
PARK (P). Idle the engine until the message center no
longer displays a message. If idling the engine does not
turn the warning message off after 10 to 15 minutes,
contact your nearest dealer or the Cadillac Roadside
Service Center. See ªRoadside Serviceº in the Index.
NOTICE:
If you keep driving your vehicle with the
transmission TRANS HOT...IDLE ENGINE
message displayed, you can damage the
transmission. This could lead to costly repairs
that may not be covered under your warranty.
The following situations can cause the transmission to
operate at higher temperatures:

Towing a trailer

Hot outside air temperatures

Hauling a heavy load

Low transmission fluid level

High transmission fluid level

Restricted air flow to the radiator and the
transmission oil cooler.
A temporary solution to hotter transmission operating
temperatures may be to let the transmission cool down.
If the transmission is operated at higher temperatures on
a frequent basis, see ªScheduled Maintenanceº in the
Index for the proper transmission maintenance intervals.

2-112
LOW COOLANT Message
This message is displayed
when the cooling system
is low on coolant.
The engine may overheat. See ªEngine Coolantº in the
Index and have your vehicle serviced as soon as you can.
CHECK COOLANT TEMP Message
This message is displayed
when the cooling system
temperature gets hot.
Check the coolant temperature gage and the coolant
level. See ªEngine Coolantº, ªEngine Coolant
Temperature Gageº and ªEngine Overheatingº in the
Index for further information.
ENGINE OVERHEATED Message
This message is displayed
when the cooling system
temperature gets too hot.
This message will be displayed after the air conditioning
system has automatically turned off for the engine
coolant protection mode. See ªEngine Overheatingº in
the Index for further information.
REDUCED ENGINE POWER Message
This message is displayed
when the cooling system
temperature gets too hot
and the engine further
enters the engine coolant
protection mode.

2-113
CHECK ENG OIL PRESSURE Message
This message is displayed
when the engine oil
pressure is low.
See ªOil Pressure Gageº in the Index for more
information.
CHECK ENG OIL LEVEL Message
This message is displayed
when the engine oil level
is low.
Once oil is added, it may need time to drain and settle in
the engine before this message will turn off. It is best to
let the engine cool down (if it is hot) or warm up (if it is
cold) and cycle the ignition to be sure this message turns
off. Refer to the dipstick for the correct level.
See ªEngine Oilº in the Index on how to check the oil
level and for what type of oil to add.

2-114
CHANGE ENGINE OIL Message
This message is displayed
when the engine oil needs
to be changed. The message
is only displayed for
15 seconds at the start of
each ignition cycle.
When you change the engine oil, be sure to reset the
Engine Oil Life Monitor. See ªEngine Oil, When to
Changeº in the Index.
SECURITY Message
This message is displayed
when the content
theft
-deterrent system has
been activated and also
monitors the Passlock


System.
If the security message is displayed continuously while
driving and stays on, there may be a problem with the
Passlock System. Your vehicle will not be protected by
Passlock, and you should see your dealer.
LOW WASHER FLUID Message
This message is displayed
when the vehicle is low on
windshield washer fluid.
The message is only
displayed for 15 seconds
at the start of each
ignition cycle.
For more information see, ªWindshield Washer Fluidº in
the Index.
SERVICE RIDE CONTROL Message
This message is displayed
when a possible problem
exists with the Road
Sensing Suspension system.

2-115
CARGO LAMP ON Message
This message is displayed
when the cargo lamps are
turned on and the ignition
key is turned to RUN.
LOW FUEL Message
This message is displayed
when your vehicle is low
on fuel.
Refer to the fuel gage for a better indication of the
amount of fuel remaining in the fuel tank.
SERVICE STABILITY SYSTEM Message
If you ever see the
SERVICE STABILITY
SYSTEM message, it means
there may be a problem
with your stability
enhancement system.
If you see this message, try to reset the system
(stop; turn off the engine; then start the engine again).
If the SERVICE STABILITY SYSTEM message still
comes on, it means there is a problem. You should see
your dealer for service. Reduce your speed and drive
accordingly. See ªStabilitrak Systemº in the Index.

2-116
STABILITY SYSTEM ACTIVE Message
You may see the
STABILITY SYSTEM
ACTIVE message on the
message center.
It means that an advanced computer
-controlled system
has come on to help your vehicle continue to go in
the direction in which you're steering. This stability
enhancement system activates when the computer senses
that your vehicle is just starting to spin, as it might if
you hit a patch of ice or other slippery spot on the road.
It also activates when it senses that your wheels are
spinning, as they might when accelerating on a road
surface that provides inadequate traction. When the
system is on, you may hear a noise or feel a vibration in
the brake pedal. This is normal. When the STABILITY
SYSTEM ACTIVE message is on, you should continue
to steer in the direction you want to go. The system is
designed to help you in bad weather or other difficult
driving situations by making the most of whatever road
conditions will permit. See ªStabilitrak Systemº in
the Index.
STABILITY SYSTEM LIMITED Message
The STABILITY SYSTEM
LIMITED message will
turn on when you press the
Stabilitrak switch; see
ªInstrument Panelº in
the Index.
While in ªLIMITEDº mode the stability system is less
likely to activate. To limit wheel spin and realize the full
benefits of the stability enhancement system, you should
normally leave Stabilitrak in its normal operating mode
(not the LIMITED mode). However, you should put
Stabilitrak in LIMITED mode if your vehicle gets stuck
in sand, mud, ice or snow and you want to ªrockº your
vehicle to attempt to free it. See ªRocking Your Vehicleº
in the Index. To exit the LIMITED mode, press the
Stabilitrak button again. The STABILITY SYSTEM
LIMITED message will be displayed whenever the
transmission is in FIRST (1). See ªStabilitrak Systemº
in the Index.

2-117
STABILITY SYSTEM DISABLED Message
The STABILITY SYSTEM
DISABLED message
indicates that the stability
enhancement system has
been temporarily disabled.
There are three conditions that can cause this message to
appear. One condition is overheating, which could
occur if the stability enhancement system activates
continuously for an extended period of time.
The STABILITY SYSTEM DISABLED message will
also be displayed if the brake system warning light is on.
See ªBrake System Warning Lightº in the Index.
Finally, the message could be displayed if the stability
system takes longer than usual to complete its diagnostic
checks due to driving conditions. The STABILITY
SYSTEM DISABLED message will turn off as soon as
the conditions that caused the message to be displayed
are no longer present. See ªStabilitrak Systemº in
the Index.
Secondary Information Center (SIC)
This section explains the features of your SIC.
The SIC provides instant information about fuel,
mileage and vehicle history in addition to allowing you
to personalize certain features of your vehicle. If you
would like to skip to the section on personalizing your
vehicle, see the section under MENU.

2-118
Fuel

Each press of the FUEL button will change the
display between the fuel remaining range, average
fuel economy, instantaneous fuel economy and a
blank display.

The average fuel economy can be reset using the
RESET button.
Trip
Each press of the TRIP button will change the display
between personal trip computer, business trip computer,
timer, vehicle history, annual mileage and a blank display.Personal Trip Computer and Business Trip Computer

Each press of the arrow button will change the
display between turn on/off, trip odometer,
fuel used, average fuel economy and average speed.

The ON/OFF button will turn the trip computer on
and off. The information on the trip computer only
gets updated when it is turned on. The personal and
business computers are independent, i.e. turning one
of them on does not turn the other off.

All information associated with the trip computer
will be reset when the RESET button is pressed.

If the RESET button is pressed and held for more
than two seconds, all of the trip computer settings
will reset starting from the last ignition cycle
(turning the ignition from OFF to RUN). This
feature is for someone who has forgotten to reset the
trip computer when pulling out of the driveway and
does not realize it until after driving for awhile.