2002 CADILLAC DEVILLE Owners Manual

3-15

RW (Rewind): Press the left arrow to rewind the
tape rapidly. The radio will play while the tape rewinds.
You may use your station pushbuttons to tune to another
radio station while in rewind. Press the left arrow again
to return to playing speed.
FF
 (Fast Forward): Press the right arrow to fast
forward to another part of the tape. The radio will play
while the tape advances. You may use your station
pushbuttons to tune to another radio station while in fast
forward. Press the right arrow again to return to playing
speed.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button to listen to selections for a few
seconds. The tape will go to a selection, play for a few
seconds, then go on to the next selection. Press this
button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing.
(Eject): Press this button to the right of the
cassette tape player to remove a tape. The radio will
play. Eject may be activated with the radio off and/or
the ignition off.
Cassette Tape Messages
If an error occurs while trying to play a cassette tape, it
could be for one of the following reasons:

The cassette tape is tight and the cassette player
cannot turn the hubs of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with a pencil. Flip the tape
over and repeat. If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used in the player. Try a new tape to be sure your
player is working properly.

The cassette tape is broken. (Check to see if your
tape is broken. Try a new tape.)
CLEAN TAPE: If this message appears on the display,
the cassette tape player needs to be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer.

3-16
Playing a Compact Disc
Insert a disc partway into the slot, label side up. The
player will pull it in. If the ignition and the radio are on
and the underlined compact disc symbol appears on the
display, the disc will begin playing. Compact discs may
be loaded with the radio off but they will not start
playing until the radio is on. If you want to insert a disc
when the ignition is off, first press the eject button.
The integral CD player can play the smaller 8 cm
compact discs. Full
-size compact discs and the smaller
compact discs are loaded in the same manner.
If an error appears on the display, see ªCompact Disc
Messagesº later in this section.

RW (Rewind): Press and hold the left arrow to
reverse the compact disc. Release it to return to playing
speed.
FF
 (Fast Forward): Press and hold the right arrow
to fast forward to another part of the compact disc.
Release it to return to playing speed.
~' TUNE SEEK !': When this button is pressed, it
has two positions. This button works the same, whether
it is pressed to the first or second position. Press this
button to seek to the next or previous track on the
compact disc.
SCAN: Press this button to listen to tracks for a few
seconds. The compact disc will go to a track, play for a
few seconds, then go on to the next track. Press this
button again to stop scanning.
RDM (Random): Press this button to hear the tracks in
random, rather than sequential, order. Press RDM again
to turn off random play.
(Eject): Press this button, located to the right of the
CD slot, to stop a CD when it is playing or to eject a CD
when it is not playing. Eject may be activated with the
radio off and/or the ignition off.

3-17
Compact Disc Messages
If the disc comes out, it could be for one of the
following reasons:

If you're driving on a very rough road. When the
road becomes smooth the disc should play.

If it's very hot. When the temperature returns to
normal, the disc should play.

The disc is upside down.

It is dirty, scratched or wet.

The air is very humid. (If so, wait about an hour and
try again.)

If the CD is not playing correctly, for any other
reason, try a known good CD.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer.AM-FM Stereo with Cassette Tape and
Compact Disc Player with Radio Data
Systems (RDS), Digital Signal Processing
(DSP) and XM Satellite Radio Service
(If Equipped)
Playing the Radio
PWR (Power): Press this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.

3-18
AVC (Automatic Volume Control): With AVC, your
audio system monitors the noise in the vehicle. Then,
AVC adjusts the volume level so that it always sounds
the same to you. To use AVC, press and hold the TONE
button until AUTO VOLUME CONTROL OFF appears
on the display. Then press the LEVEL plus symbol.
AUTO VOLUME CONTROL ON will appear on the
display. AVC VOLUME will appear on the display any
time you adjust the volume while AVC is on. To turn
AVC off, press and hold the TONE button until AUTO
VOLUME CONTROL ON appears on the display. Then
press the LEVEL minus symbol. AUTO VOLUME
CONTROL OFF will appear on the display.
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing one of these buttons.
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.Finding a Station
BAND: Press this button to select AM, FM1 or FM2,
weather or XM1 or XM2 if your radio is equipped with
XM
Satellite Radio Service.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds to
scan radio stations. The radio will go to a station, play
for five seconds, then go on to the next station. Press
this button again to stop scanning.
To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.

3-19
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations and associated tone and DSP settings.
The RDS PTY mode must be off to use this mode. You
can set up to 36 stations (six AM, six FM1, six FM2,
six XM1, six XM2 and six weather if your radio is
equipped with the XM Satellite Radio Service), by
performing the following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1, FM2, XM1, XM2
or weather.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds. Whenever you press that
numbered pushbutton for less than two seconds, the
station you set will return.
5. Repeat the steps for each pushbutton.
When battery power is removed and later applied, you
will not have to reset your radio presets because the
radio remembers them.Setting the Tone (Bass/Treble)
TONE: Press and release this button until the desired
tone BASS, TREBLE or MIDRANGE appears on the
display. The radio keeps separate tone settings for each
band, preset (except weather band presets) and source.
- LEVEL +: After selecting the desired tone control,
press the plus or minus symbol on this button to select
the desired level.
To save the tone settings for your presets, press and hold
the numbered button for the desired preset for more than
two seconds until you hear a beep.
Adjusting the Speakers (Balance/Fade)
TONE: Press and release this button until BALANCE
or FADE appears on the display.
- LEVEL +: After selecting the desired control, press
the plus or minus symbol on this button to select the
desired level.
To save the tone settings for your presets, press and hold
the numbered pushbutton for the desired preset for more
than two seconds until you hear a beep.

3-20
Using DSP
DSP (Digital Signal Processing): This feature is used to
provide a choice of four different listening experiences:
talk, front seat, ambience and spacious. DSP can be used
while listening to the radio, the cassette tape player or the
CD player. Press this button to turn DSP on. Press and
release this button until the desired selection appears on
the display. To turn DSP off, press and hold this button
until DSP OFF appears on the display. When DSP OFF
is displayed, the system will provide the best overall audio
performance. The radio keeps separate DSP settings for
each band (except weather band, which is always set to
talk), preset and source.
TALK: This setting should be used when listening to
non
-musical material such as news, talk shows, sports
broadcasts and books on tape. TALK makes spoken
words sound very clear.
FRONT SEAT: This setting adjusts the audio to give
the driver the best possible sound qualities. Front seat
can be used at any time for any material. Rear seat
passengers in the vehicle may not get the same effect.
AMBIENCE: This setting is used to enhance the
stereo effect.
SPACIOUS: This setting is used to make the listening
space seem larger.Using RDS
Your audio system is equipped with Radio Data Systems
(RDS). RDS mode gives you many useful new features.
With RDS the radio can:

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies,

receive and display messages from radio stations and

search for a stronger station when a station is too
weak for listening.
RDS features are only available for use on FM stations
which broadcast RDS information.
RDS (Radio Data Systems): If you are tuned to a
station broadcasting RDS information, the station's call
letters and Program Type (PTY) will replace the
station's frequency on the display. After five seconds,
the program type will be replaced on the display by the
station's program type name. The program type and
program type name may be the same or different. Press
BAND to recall the frequency and program type
displays. If the radio is tuned to a station that is not
broadcasting RDS information, the station's frequency
will remain on the display. With RDS the radio will
search for a stronger station in the network when a
station gets too weak for listening.

3-21
HR (Hour) or MN (Minute): When tuned to an RDS
station, press these buttons to display the time for the
current station. STATION TIME IS will be displayed. If a
time has not been sent to the radio, NO STATION TIME
will be displayed. If you have recently tuned to the station,
you may need to wait a minute before the time is available
to the radio. To set the clock to the current displayed
station time, press HR or MN until TIME UPDATED is
displayed. You must be tuned to an FM RDS station.
RDS Messages
ALERT: This type of announcement warns of national or
local emergencies. You will not be able to turn off alert
announcements. ALERT appears on the display when an
alert announcement plays. The radio uses TA volume during
these announcements. To increase volume, turn the
PWR/VOL knob clockwise. Turn it counterclockwise to
decrease volume. TA VOLUME will appear on the display
while the volume is being adjusted. When an alert
announcement comes on the current radio station or a related
network station, you will hear it, even if the volume is muted
or a cassette tape or compact disc is playing. If the radio tunes
to a related network station for an alert announcement, it will
return to the original station when the announcement is
finished. If the cassette tape or compact disc player is
playing, play will stop for the announcement and resume
when the announcement is finished.TA (Traffic Announcement): This feature allows
the radio to receive traffic announcements even with
the volume muted, or when listening to a CD or
cassette tape.
When the TA button is pressed and released, the radio
will search for a station with TA if the current station is
not TA capable. During the search TA will flash on the
display. Once a TA station is found, TA will appear on
the display and the traffic announcement will be played.
If no station broadcasting traffic announcements is
found, NO TRAFFIC STATION FOUND will appear on
the display. If the TA button is pressed and held for
two seconds, the radio will search for the next available
TA station.
While a traffic announcement plays, the radio uses a
special type of volume called TA volume. To increase
TA volume, turn the VOL knob clockwise. Turn it
counterclockwise to decrease volume. TA VOLUME
will appear on the display while the volume is
being adjusted.

3-22
When a traffic announcement comes on the current radio
station or a related network station, you will hear it,
even if the volume is muted or a cassette tape or
compact disc is playing. If the radio tunes to a related
network station for a traffic announcement, it will return
to the original station when the announcement is
finished. If the cassette tape or compact disc player was
being used, the tape or compact disc will stay in the
player and resume play at the point where it stopped.
Press the TA button again to turn TA off.
MSG (Message): If the current station has a message,
MSG will appear on the display. Press the MSG button,
to see the message. If the whole message does not appear
on the display, parts of the message will appear every three
seconds until the message is completed. To see the parts
of the message faster than every three seconds, press the
MSG button again. A new group of words will appear
on the display. Once the complete message has been
displayed, MSG will disappear from the display until
another new MSG is received.
XM
Satellite Radio (If Equipped)
XM is a national satellite radio service that offers up to
100 coast to coast channels including music, news,
sports, talk and children's programming. XM providesdigital quality audio and text information, including
song title and artist name. A service fee is required
in order to receive the XM service. For more
information, contact XM at www.xmradio.com or
call 1
-800-852-XMXM (9696).
MSG (Message): Press this button while in XM mode
to retrieve various pieces of information related to the
current song or channel. By pressing and releasing the
MSG button, you may retrieve four different categories
of information: Artist Name/Feature, Song/Program
Title, Channel Category, and other Additional
Information that may be broadcast on that channel.
Additional Information messages may only be available
at certain times or on certain programs. If an Additional
Information message is being broadcast on the tuned
channel, MSG will appear on the display.
Each of the four information types may have multiple
pages of text. To reach a category, press and release the
MSG button consecutively until the desired type is
displayed. If there are multiple pages of text for the
information selected type, the radio will automatically
display all the pages for that type at a rate of
approximately one page every three seconds before
timing out and returning to the default display. You may
override this feature by pressing the MSG button to
review all of the pages at your own pace.