2002.5 Peugeot 406 warning

29-07-2002
Rear seats, estate
To fold down the rear seat:
remove the head restraints bypressing the lug.
tilt the seat cushion against the front seats, using the strap. secure the side seat belt buckles
on the coat hooks when manoeu
vring the seat back to avoid any
risk of the straps being damaged.
unlock the seat back by pressing button 1. The red marker Aappears.
fold down the seat back gently to avoid blocking the centre belt.
When returning the seat back to the
upright position, ensure that it is
correctly locked (red marker Ano
longer visible). When driving with rear passengers
with one third of the seat folded
down, release the central seat belt
buckle from its catch.
YOUR 406 IN DETAIL
115
WARNING
Do not remove
the seat back of the estate's onepiece rear seat.
This seat is fitted with return springs which cancause injury.
Contact a
PEUGEOT dealer
if you wish to remove the seat back.

29-07-2002
SEAT BELTS
To adjust the height of the front
seat belts
Pinch control 1and slide it.
To lock the seat belts
Pull the strap, then insert the buckle
into the stalk. Pretensioning and forcelimiting
front seat belts
Safety in the event of a frontal impact
has been improved by the introduc
tion of pretensioning and forcelimit
ing front seat belts. Depending on
the seriousness of the impact, the
pretensioning system instantly tight
ens the seat belt firmly against the
body of the occupant.
The pretensioning seat belts are
active when the ignition is on.
The forcelimiting device reduces the
pressure of the seat belt against the
occupant's body in the event of an
accident.
Rear seat belts
The three rear seats are all fitted with
threepoint inertia reel belts.
YOUR 406 IN DETAIL
121
To be effective, a seat
belt must be tightened as
close to the body as pos
sible.
Depending on the nature and the
seriousness of the impact, the
pretensioners may be triggered
before and independently of the
air bags.
In all cases, the air bag warning
light comes on.
Following a collision, have the
system checked by a PEUGEOT
dealer.
The system has been designed to
be fully operational for ten years.
Have it replaced after this period.

THE KEYS
The keys allow you to switch on the
ignition and to independently operate
the locks on the front door, the glove
box and the passenger air bag dis
arming switch.
Central locking
From the driver's door, the keys
allow you to lock, deadlock* and
unlock the doors and boot/tailgate.
If one of the front doors is open, the
central locking does not work.
The remote control performs the
same functions at a distance.
The remote control
Locking
Press button Ato lock the vehicle.
YOUR 406 IN DETAIL 105
This is confirmed by fixed lighting of
the direction indicators for approxi
mately two seconds.
Unlocking
Press button
B to unlock the vehicle.
This is confirmed by rapid flashing of
the direction indicators.
Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You risk caus
ing it not to work and the remote con
trol would have to be reprogrammed. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management
system as soon as the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly,
an audible signal sounds,
accompanied by a message on the
multifunction display.
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible.
Locating your car
To locate your car, if you have locked
it, in a car park: 
press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition.
29-07-2002

29-07-2002
YOUR 406 IN DETAIL
106
Changing the battery of the
remote control
The information 'battery flat' is
given by an audible signal accompa
nied by a message on the multi
function display.
To replace the battery, unclip the
casing using a coin at the ring
(CR2016/3 volt battery).
If the remote control does not work
after the battery has been changed,
reprogramme the remote control.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film, which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.
Programming the remote
control Switch off the ignition.
 Switch the ignition on again.
 press button A.
 Switch off the ignition and
remove the remote control key
from the ignition lock. The remote
control is now working again.
DEADLOCKING
Deadlocking the doors is an addtional
safety device.
Warning:
The internal and external door
controls cannot operate when the vehi
cle is deadlocked.
There are two methods of operation:
With the the remote control
To deadlock: pressbutton A.
This is indicated by permanent lighting
of the direction indicators for approxi
mately two seconds.
Press button A within five seconds
of deadlocking to change this to lock
ing only.
This is indicated by permanent lighting
of the direction indicators for approxi
mately two seconds.
With the ignition key from the driver's
door
To deadlock: turn the key towards the
rear of the vehicle.
To lock: within five seconds of deadlock
ing, again turn the key towards the rear
of the vehicle. To unlock: turn the key
towards the front of the vehicle.
Do not operate the dead
locking if there is someone
inside the vehicle.
Do not operate the buttons
of yur remote control while it is in
your pocket, as there is a possibility
that it may unlock your vehicle.

THE KEYS
The keys allow you to switch on the
ignition and to independently operate
the locks on the front door, the glove
box and the passenger air bag dis
arming switch.
Central locking
From the driver's door, the keys
allow you to lock, deadlock* and
unlock the doors and boot/tailgate.
If one of the front doors is open, the
central locking does not work.
The remote control performs the
same functions at a distance.
The remote control
Locking
Press button Ato lock the vehicle.
YOUR 406 IN DETAIL 105
This is confirmed by fixed lighting of
the direction indicators for approxi
mately two seconds.
Unlocking
Press button
B to unlock the vehicle.
This is confirmed by rapid flashing of
the direction indicators.
Note: do not repeatedly press the
button of your remote control out of
range of your vehicle. You risk caus
ing it not to work and the remote con
trol would have to be reprogrammed. ELECTRONIC ENGINE
IMMOBILISER
This locks the engine management
system as soon as the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code is
recognised and starting is possible.
If the system does not function
correctly,
an audible signal sounds,
accompanied by a message on the
multifunction display.
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible.
Locating your car
To locate your car, if you have locked
it, in a car park: 
press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition.
29-07-2002

29-07-2002
SPECIAL FEATURES
170
THE ALARM SYSTEM
Setting and disarming the
alarm
Setting and deactivating the alarm
The alarm completes the security
equipment for your vehicle. It offers
two types of protection. exterior protection: when it is set,
the alarm sounds if a door, the
boot or the bonnet is opened;
interior protection: when it is set,
the alarm sounds if the sensors
detect a variation in the air move
ment inside the vehicle (break
ing of a window) or movement
inside the vehicle.
The alarm is also equipped with an
antitamper function.
The alarm is also equipped with an
antitamper function.
If an attempt is made to tamper with
the wires to the siren, control unit or
the battery, the alarm is triggered:
the siren sounds and the headlamps
come on. Setting the alarm
(interior and exterior protection)
Switch the ignition off and get out
of the vehicle.
Press the locking button of the remote
control key.
The doors lock.
The direction indicators light for two
seconds.
The red light on the switch flashes once
a second.
5 seconds later, exterior protection is set.
50 seconds later, interior protection is set.
Note:
when the alarm is triggered, the
siren sounds for thirty seconds. After
the thirty seconds it stops, but the
alarm remains set.
Warning
If, on setting the alarm, a door, the boot
or the bonnet are not closed correctly,
the siren sounds for a moment. If the
vehicle is closed correctly in the follow
ing 45 seconds, the alarm is set and
the direction indicators remain on for
two seconds. In all cases, the alarm is
set after 45 seconds. Disarming the alarm
(interior and exterior protection)
Press the unlocking button of the
remote control key.
The doors unlock.
The direction indicators flash for two
seconds.
The red warning light on the switch
goes out.
Note:
if the warning light continues
to flash after disarming the alarm, it
is a sign that the alarm has been trig
gered. The flashing will stop when
the ignition is switched on.

29-07-2002
AUTOMATIC SWITCHING ON
OF THE LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off as soon as the light
becomes bright enough or the wind
screen wipers stop.
This function is active when the vehi
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories
position (1st notch),
 Press the end of the lights stalk
for more than two seconds.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. Because of this, the lights do
not come on automatically.
Do not cover the brightness sen
sor connected to the rain sensor,
located in the windscreen behind
the mirror. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting of
the headlamps activated" on the
multifunction display.
Note: Always operate the lighting
controls manually where this is pos
sible.
Disarming
Disarming of the function is accom
panied by an audible signal.
When driving, if this function is
switched off when the headlamps
would switch on in automatic mode,
the lights remain on.
It is however possible to disarm this
function and switch off the lights by:
manually switching off the lights using the lights stalk,
switching off the engine.
YOUR 406 IN DETAIL 123
If the brightness sensor does not
function correctly, the system acti
vates the function (the lights come
on).The driver is alerted by the flash
ing of the ''dipped beam'' warning
light on the instrument panel.
Contact a PEUGEOT dealer to have
the system checked.
Follow me Home
When there is a low level of bright
ness or at night, if you leave your
vehicle, the side lights and the
dipped beam lights may remain on
for approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories
position (first notch),
 press the end of the lights stalk for
more than two seconds,
 place the lights stalk in the 0posi
tion,
 flash the headlamps,
 get out of the car and lock it.

29-07-2002
HORN
Press one of the spokes or
the centre of the steering
wheel.
Adjusting the headlamps
Depending on the load in your vehi
cle, adjusting the beam of the head
lamps is recommended as follows.0 1 or 2 people in the front seats.
– 3 people.
1 5 people.
2 5 people + maximum
authorised load.
3 Driver + maximum
authorised load.
Initial setting is position 0. Hazard warning lights
Press the button, the direction indi
cators flash.
They can operate with the ignition
off.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
When the vehicle is stationary,
unlock the steering wheel by pulling
handle
A.
Adjust the height and depth of the
steering wheel, then lock it by push
ing handle Adown fully.
YOUR 406 IN DETAIL
142
Automatic lighting of hazard
warning lights*
When braking in an emergency,
depending on the force of decelera
tion, the hazard warning lights come
on automatically. They switch off
automatically the first time you accel
erate.
It is also possible to switch them off
by pressing the button.* According to destination.