2001 TOYOTA SEQUOIA 4WD

F13991
GNDCSW*1
Center Integration Panel Assembly
CSW
*2
C3C6
DI±1050
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1244 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Check operation of the VSC OFF (TRAC OFF) indicator light.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and push the hand±held tester main switch ON.
(c) Select ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºONº and ºOFFº of the VSC OFF (TRAC OFF) indicator light can be shown on the combination
meter with the hand±held tester.
ItemVehicle Condition / Test DetailsDiagnostic Note
VSC OFF (TRAC OFF)Turns VSC OFF (TRAC OFF) indicator ON / OFFObserve combination me-
ter
OK:
VSC OFF (TRAC OFF) indicator light comes on.
NG Go to step 4.
OK
2 Check center diff. lock (TRAC OFF) switch.
PREPARATION:
Remove center integration panel assembly (See page
BO±85).
CHECK:
Measure the resistance between terminals CSW and GND of
the center diff. lock
*1
(TRAC OFF *2) switch when the center diff.
lock
*1 (TRAC OFF *2) switch is ON and OFF.
*1
: Only for 4WD
*2 : Only for 2WD
OK:
Center diff. lock (TRAC OFF) switchResistance
Press continuouslyContinuity
Release1MW or higher
NG Replace center diff. lock (TRAC OFF) switch.
OK

DID8P±01
I28566
Seat Position
Control ECU
A/C ECU (Integration
Control Panel) BEANBody ECU
Back Door ECU
ECM
Light Control
Rheostat
Vehicle Speed
Sensor
Oil Pressure
Sender Gauge
Fuel Sender Gauge
Seat Inner
Belt Switch
Park/neutral
Position Switch
Turn Signal
Flasher Relay
Washer Level SensorKey Unlock
Warning Switch
Door Courtesy
Lamp Switch
Parking Brake Switch
Transponder
Key ECU
4WD Control ECU
Airbag Sensor
Center ECU Combination
Meter
Skid Control ECU
Suspension
Control ECU
Translate ECU
Overhead Module
(Garage Door
Opener)BEAN
BEAN
BEAN
BEAN
BEAN BEAN
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1605
1799 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DIAGRAM

DID8Q±01
DI±1608
± DIAGNOSTICSCOMBINATION METER SYSTEM
1802 Author: Date:
2005 SEQUOIA (RM1146U)
SYSTEM DESCRIPTION
1. METER GAUGE AND WARNING/INDICATOR
GAUGE:
ItemDetail
SpeedometerVehicle speed sensor (Direct line).
TachometerECM transmits engine speed to the meter to display.
ODO/TRIP MeterCombination meter assy.
FuelDisplays a fuel level according to a signal from the fuel sender gauge (Direct line).
Water TemperatureDisplays engine coolant temperature according to a signal from the ECM (BEAN).
Oil PressureReceives a signal from the oil pressure sender (Direct line).
Volt MeterDisplays vehicle voltage according to a voltage from the IG terminal (Direct line).
WARNING/INDICATOR:
HINT:
Combination meter bulb check is performed for 3 seconds after the ignition switch is turned ON.
ItemDetailList of indicators available for
bulb check
O/D OFFReceives a signal from the ECM (Direct line)±
TURNTurns signal switch ON (Direct line)±
BEAMReceives a signal from the body ECU (*1), Displays a signal received from the
dimmer switch (*2) (Direct line)±
SECURITYReceives a set signal from the transponder key ECU and body ECU (Direct line)±
CHARGEReceives a malfunction signal from the alternator (Direct line)
AIR BAGReceives a malfunction signal from the airbag sensor center (Direct line)
D SEAT BELTReceives the driver seat belt signal (Unfastened) from the seat belt inner front LH
(Direct line)±
DOOROpen door indicator comes on when a signal is received from the ECU (BEAN)
from each door±
A/T OIL TEMP.Warning is displayed when the oil temperature is high (Direct line)
BRAKEComes on when the parking brake switch is on or the brake fluid level warning
switch is on (Direct line)
MIL (CHECK ENGINE)Receives a malfunction signal from the ECM (Direct line)
FUEL WARNINGReceives the fuel empty signal from the fuel sender gauge (Direct line)±
ABSReceives a malfunction signal from the skid control ECU (Direct line)
WASHERWarning is displayed when the washer level is low (Direct line)±
CRUISEReceives a CRUISE on signal or malfunction signal from the ECM (Direct line)±
VSC TRACReceives a malfunction signal from the skid control ECU (Direct line)
VSC (TRAC) OFFReceives a malfunction signal from the translate ECU (Direct line)
SLIPReceives a malfunction signal from the translate ECU (Direct line)
4HIReceives a 4HI signal from the 4WD control ECU (Direct line)±
CTR DIF LOCKReceives a DIF LOCK signal from the 4WD control ECU (Direct line)±
A/T PReceives a P signal from the park/neutral position switch (Direct line)±
A/T NReceives an N signal from the park/neutral position switch (Direct line)±
A/T DReceives a D signal from the park/neutral position switch (Direct line)±
A/T 3Receives a 3 signal from the park/neutral position switch (Direct line)±
A/T 2Receives a 2 signal from the park/neutral position switch (Direct line)±
A/T LReceives an L signal from the park/neutral position switch (Direct line)±

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1609
1803 Author: Date:
2005 SEQUOIA (RM1146U)A/T R
Receives an R signal from the park/neutral position switch (Direct line)±
TAIL/HEADReceives a dimmer signal from the body ECU (BEAN)±
TIRE PRESSUREReceives a low tire pressure signal from the tire pressure monitor ECU (Direct line)
4LOReceives a 4LO signal from the 4WD control ECU (Direct line)±
MAIN REQD (Blinks)Blinks when 4,500 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
MAIN REQD (Comes on)Blinks when 5,000 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
RSCA OFFReceives an RSCA OFF signal from the airbag sensor center (Direct line)
HIReceives a suspension position HI signal from the suspension control ECU (Direct
line)
NReceives a suspension position N signal from the suspension control ECU (Direct
line)
LOReceives a suspension position LO signal from the suspension control ECU (Direct
line)
AHC MAN.Receives a suspension control manual signal from the suspension control ECU
(Direct line)
*1: w/ Day time running light
*2: w/o Day time running light
BUZZER:
ItemDetail
Key ReminderBuzzer is ON: Ignition switch is OFF, key is inserted, and door is open.
Fasten BeltBuzzer is ON: Ignition switch is ON and seat belt is unfastened.
2. COMBINATION METER IN SEQUOIA HAS THE FOLLOWING FEATURES:
(a) Built±in buzzer for the reminder system (key and seat belt)
(b) Integrated trip and odometer knobs

Press and release knob to scroll through trip ºAº, trip ºBº, and odometer features.

Press and hold the trip knob to reset trip meter functions.
(c) Oil maintenance indicator

When 4,500 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor begins to blink for 15 seconds after the ignition switch is turned to the ON position.

When 5,000 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor comes on.

Press and hold the trip knob to reset the oil maintenance indicator.
(d) Rotate knob to adjust interior illumination

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1615
1809 Author: Date:
2005 SEQUOIA (RM1146U) Seat belt warning lamp for driver's seat does not operate.
Refer to troubleshooting proceduresDI±1650
SLIP warning light does not come on.
1. SLIP warning light circuit
2. Wire harness and connector
3. Combination meter assy
4. Skid control ECUDI±1041
±
IN±35
IN±35
INDICATOR LIGHTS:
SymptomSuspected AreaSee page
Turn indicator light does not come on.
1. Turn signal flasher relay
2. Wire harness or connector
3. Combination meter assyBE±36
±
IN±35
High beam indicator light does not come on.
1. Headlight dimmer switch (*1)
Headlight dimmer switch circuit (*2)
2. Wire harness or connector
3. Combination meter assyBE±27
DI±1755
±
IN±35
Washer level indicator light does not come on.
1. Washer level warning switch
2. Wire harness or connector
3. Combination meter assyBE±49
±
IN±35
Tire pressure indicator light does not come on.
1. Tire pressure monitor ECU
2. Wire harness or connector
3. Combination meter assyDI±873
±
IN±35
CRUISE main indicator light does not come on.
1. CRUISE main indicator light circuit
2. Cruise main control switch circuit
3. Wire harness or connector
4. Combination meter assyDI±1557
DI±1561
±
IN±35
VSC OFF indicator light does not come on.1. VSC OFF indicator light circuit
2. Combination meter assyDI±1048
IN±35
VSC TRAC indicator light does not come on.1. VSC TRAC indicator light circuit
2. Combination meter assyDI±1027
IN±35
Security indicator light does not come on.1. Security indicator light circuit
2. Combination meter assyDI±1731
IN±35
4HI indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
4LO indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
CTR DIF LOCK indicator light does not come on.
1. Wire harness and connector
2. Combination meter assy
3. 4WD control ECU±
IN±35
IN±35
Height control indicator lamp does not come on.1. Height control indicator lamp circuit
2. Combination meter assyDI±785
IN±35
Height control manual indicator lamp does not come on.1. Height control manual indicator lamp circuit
2. Combination meter assyDI±789
IN±35
A/T indicator light does not come on.
1. Park/neutral position switch circuit
2. Wire harness and connector
3. Combination meter assyDI±576
±
IN±35
*1: w/o Day time running light
*2: w/ Day time running light
OTHERS:
SymptomSuspected AreaSee page
All buzzers (key reminder, seat belt) do not operate.Combination meter assyIN±35

I28567
GND DI±1620
± DIAGNOSTICSCOMBINATION METER SYSTEM
1814 Author: Date:
2005 SEQUOIA (RM1146U) C6±14 ± Body ground
P ± Body groundHeight control indicator
lamp signal (LO)Height control indicator lamp LO,
Indicator light ONBelow 1 V
C6±14 ± Body groundP ± Body groundHeight control indicator
lamp signal (LO)Height control indicator lamp LO,
Indicator light OFF10 to 14 V
C6±15 ± Body groundB±L ± Body
groundHeight control indicator
lamp signal (N)Height control indicator lamp N, In-
dicator light ONBelow 1 V
C6±15 ± Body groundB±L ± Body
groundHeight control indicator
lamp signal (N)Height control indicator lamp N, In-
dicator light OFF10 to 14 V
C6±16 ± Body groundGR±R ± Body
groundHeight control indicator
lamp signal (HI)Height control indicator lamp HI, In-
dicator light ONBelow 1 V
C6±16 ± Body groundGR±R ± Body
groundHeight control indicator
lamp signal (HI)Height control indicator lamp HI, In-
dicator light OFF10 to 14 V
C6±17 (*3) ± Body groundR±G ± Body
groundHi±Beam signalHi±Beam OFFBelow 1 V
C6±17 (*3) ± Body groundR±G ± Body
groundHi±Beam signalHi±Beam ON10 to 14 V
C6±18 (*4) ± Body groundGR±L ± Body
groundHi±Beam signalHi±Beam OFFBelow 1 V
C6±18 (*4) ± Body groundGR±L ± Body
groundHi±Beam signalHi±Beam ON10 to 14 V
C6±19 ± Body groundG±B ± Body
groundTurn signal (L)Ignition switch ON, turn signal LH
indicator OFFBelow 1 V
C6±19 ± Body groundG±B ± Body
groundTurn signal (L)Ignition switch ON, turn signal LH
indicator ON10 to 14 V
C6±21 ± Body groundR±W ± Body
groundABS signalABS warning light ON6.7 to 12 V
C6±21 ± Body groundR±W ± Body
groundABS signalABS warning light OFFBelow 1 V
C6±23 ± Body groundW±R ± Body
groundBatteryAlways10 to 14 V
C6±24 ± Body groundB±O ± Body
groundIgnition switch signal (ON)Ignition switch OFFBelow 1 V
C6±24 ± Body groundB±O ± Body
groundIgnition switch signal (ON)Ignition switch ON10 to 14 V
*1: 4WD
*2: w/ Driving position memory
*3: w/o Daytime running light
*4: w/ Daytime running light
*5: 2WD
Waveform 1 (Reference):
ConditionGauge set
Engine idle speed5 V/DIV, 10 ms/DIV

I27707
C6±21
C6±8
(*4) C5±15
C5±18
C5±2
C5±14
C5±19
C5±13
C6±1
C6±2
C6±3
C5±20ABS
CHARGE
A/T OIL TEMP
CHECK E/G
4LO O/D OFF
A/T L
WASHER
SLIP
VSC OFF
VSC TRAC
4HI CRUISE
ONE STEP
DIMMERC6±24
C6±5
C6±6
C6±4
C5±40TIRE PRS
CTR DIFF LOCK
RSCA OFF
SECURITY
P
R
NC5±16
C5±17
C5±34
C5±35
C5±36
C5±37
C5±38
C5±39
C6±17 (*5)
C6±18 (*6)
C5±33
C6±19 TURN (L) TURN (R) BEAM3
2 D
*4: 4WD *5: w/o Daytime Running Light *6: w/ Daytime Running LightONE STEP
DIMMERRSCA OFF
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1623
1817 Author: Date:
2005 SEQUOIA (RM1146U)

Wire harness side
1
2
3
4
5
6
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
401
2
3
4
5
8 6
10
11
12
13
14
15
16
17
18
19
21
23
24
Terminal No.
Translate ECU
ECM
STA Fuse
Front Seat Inner Belt LH (Buckle Switch)
Overhead Module (Garage Door Opener)
Overhead Module (Garage Door Opener)
Washer Level Sensor
ECM
ECM (*1)
Transponder Key Computer
Body ECU
ECM
ECM
Tire Pressure Monitor ECU
Injector No. 1
Light Control Rheostat
ECM
Speed Sensor
4P OUT (Other Parts)
Fuel Sender Gauge
Oil Pressure Sender Gauge
IGN Fuse
Airbag Sensor Assembly
Memory Seat ECU and SW (*2)
Back Door ECU
Integration Control and Panel
Turn Signal Flasher Relay
Park/Neutral Position Switch
Airbag Sensor AssemblyTranslate ECU
Translate ECU
Skid Control ECU
4WD Control ECU
Alternator
Speed Sensor
Fuel Sender Gauge
Ground
Suspension Control ECU
Body ECU (*4)
Body ECU (*3)
Turn Signal Flasher Relay
Skid Control ECU
ECU±B Fuse
IGN1 Fuse Connectors:
Terminal No.
Wire harness side
C5
C64WD Control ECU
4WD Control ECU
Suspension Control ECU
Suspension Control ECU
Suspension Control ECU
*1: 4WD
*2: w/ Driving Position Memory
*3: w/ Daytime Running Light
*4: w/o Daytime Running LightPark/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch
Park/Neutral Position Switch DI±1624
± DIAGNOSTICSCOMBINATION METER SYSTEM
1818 Author: Date:
2005 SEQUOIA (RM1146U)