2001 TOYOTA SEQUOIA check engine

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1617
1811 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Reconnect the C5 and C6 connectors.
(d) Measure the voltage of each terminal of the wire harness side connector.
Standard:
Terminals No.Wiring ColorTerminal DescriptionConditionSpecified Condition
C5±1 ± Body groundR±B ± Body
groundParking brake signalParking brake warning light ON6.7 to 12 V
C5±1 ± Body groundR±B ± Body
groundParking brake signalParking brake warning light OFFBelow 1 V
C5±2 ± Body groundLG±R ± Body
groundCRUISE signalCRUISE indicator light ONBelow 1 V
C5±2 ± Body groundLG±R ± Body
groundCRUISE signalCRUISE indicator light OFF10 to 14 V
C5±3 ± Body groundB ± Body groundIgnition switch signal
(Start)Ignition switch OFFBelow 1 V
C5±3 ± Body groundB ± Body groundIgnition switch signal
(Start)Ignition switch START10 to 14 V
C5±4 ± Body groundG±Y ± Body
groundSeat belt condition signal
(Driver side)D±BELT indicator light ONBelow 1 V
C5±4 ± Body groundG±Y ± Body
groundSeat belt condition signal
(Driver side)D±BELT indicator light OFF10 to 14 V
C5±13 ± Body groundLG±R ± Body
groundWasher level signalWASH LVL indicator light ONBelow 1 V
C5±13 ± Body groundLG±R ± Body
groundWasher level signalWASH LVL indicator light OFF10 to 14 V
C5±14 ± Body groundL±O ± Body
groundO/D OFF indicator signalO/D OFF indicator light ONBelow 1 V
C5±14 ± Body groundL±O ± Body
groundO/D OFF indicator signalO/D OFF indicator light OFF10 to 14 V
C5±15 (*1) ± Body groundY±R ± Body
groundA/T oil temperature signalA/T OIL TEMP. warning light ONBelow 1 V
C5±15 (*1) ± Body groundY±R ± Body
groundA/T oil temperature signalA/T OIL TEMP. warning light OFF10 to 14 V
C5±16 ± Body groundLG±B ± Body
groundSecurity indicator light
signal (Engine immobilizer
system)
Security indicator light ON10 to 14 V
C5±16 ± Body groundLG±B ± Body
groundSecurity indicator light
signal (Engine immobilizer
system)
Security indicator light OFFBelow 1 V
C5±17 ± Body groundGR ± Body
groundSecurity indicator light
signal (Theft deterrent
system)
Security indicator light ON10 to 14 V
C5±17 ± Body groundGR ± Body
groundSecurity indicator light
signal (Theft deterrent
system)
Security indicator light OFFBelow 1 V
C5±18 ± Body groundV±W ± Body
groundCHECK ENGINE signalCHECK ENGINE warning light ONBelow 1 V
C5±18 ± Body groundV±W ± Body
groundCHECK ENGINE signalCHECK ENGINE warning light OFF10 to 14 V
C5±19 ± Body groundG±B ± Body
groundA/T shift position signal
(L)A/T L indicator OFFBelow 1 V

DI±1630
± DIAGNOSTICSCOMBINATION METER SYSTEM
1824 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check fuse.
CHECK:
Measure the resistance of the IGN2 fuse and IGN1 fuse in the instrument panel J/B.
OK:
Below 1 W
CHECK:
Measure the resistance of the STA fuse in the engine room R/B.
OK:
Below 1 W
CHECK:
Measure the resistance of the ECU±B fuse and AM2 fuse in the engine room R/B.
OK:
Below 1 W
NG Inspect for short circuit in harness and all com-
ponents connected to fuse.
OK

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1637
1831 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
TACHOMETER0 rpm / 1,000 rpm / 2,000 rpm / 3,000 rpm / 4,000
rpm / 5,000 rpm / 6,000 rpm / 7,000 rpmConfirm that the vehicle is stopped and engine is
idling.
OK:
Tachometer readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±35).
OK
2 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item/
Range (Display)Normal ConditionDiagnostic Note
TACHO METEREngine RPM /
Min.: 0 rpm Max.: 12,750 rpmAlmost the same as actual engine
speed (When engine is running)
OK:
Engine speed displayed on the tester is almost the same as the actual engine speed.
OK Replace combination meter
(See page IN±35).
NG

I28571
C5±23
Combination Meter:
I28567
GND
DI±1638
± DIAGNOSTICSCOMBINATION METER SYSTEM
1832 Author: Date:
2005 SEQUOIA (RM1146U)
3 Inspect combination meter.
PREPARATION:
(a) Check the input signal waveform.
(1) Remove the combination meter with the connectors
connected.
(2) Connect the oscilloscope to terminal C5±23 and
body ground.
(3) Start the engine.
CHECK:
Check signal waveform according to the condition(s) in the
table below.
ItemCondition
Tool setting5 V/DIV, 10 ms/DIV
Vehicle conditionEngine idle speed
OK:
Waveform appears as shown in the illustration.
HINT:
As engine speed increases, the cycle of the signal waveform
narrows.
OK Replace combination meter
(See page IN±35).
NG

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1641
1835 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
FUEL GAUGEEMPTY, 1/2, FULLConfirm that the vehicle is stopped and engine is
idling.
OK:
Fuel receiver gauge readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±24).
OK
2 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
FUEL GAUGEFuel Input /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the fuel receiver gauge
angle.

OK:
Fuel value signal displayed on the tester is almost the same as the needle indication.
NG Replace combination meter
(See page IN±24).
OK

DI±1644
± DIAGNOSTICSCOMBINATION METER SYSTEM
1838 Author: Date:
2005 SEQUOIA (RM1146U)
Malfunction in engine coolant temperature receiver gauge
CIRCUIT DESCRIPTION
The ECM receives an engine coolant temperature signal from the engine coolant temperature sensor and
sends it to the A/C ECU.
The combination meter receives the signal from the A/C ECU through multiplex communication. Therefore,
if a malfunction occurs in the engine coolant temperature receiver gauge, there may be a malfunction in the
multiplex communication system, air conditioning system, or engine system.
(Multiplex communication system: See page DI±1892)
(Air conditioning system: See page DI±2301)
(Engine system: See page DI±9)
INSPECTION PROCEDURE
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
COOLANT TEMPHIGH / NORMAL / LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
OK:
Engine coolant temperature receiver gauge readings change according to hand±held tester op-
eration.
OK Go to engine system or air conditioning system
(See page DI±9 or DI±2301).
NG
Replace combination meter
(See page IN±35).
DID92±01

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1651
1845 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
SEAT BELT BUZZROFF / ONConfirm that the vehicle is stopped and engine is
idling.
D BELT REMINDOFF / ONConfirm that the vehicle is stopped and engine is
idling.
OK:
Switch condition (ON/OFF) can be switched by ACTIVE TEST.
NG Replace combination meter
(See page IN±35).
OK

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1655
1849 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
OIL PRESS METERHIGH, 3/4, 1/2, 1/4, LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
OK:
Oil pressure receiver gauge readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±35).
OK