2001 TOYOTA PRIUS oil level

2001 PRIUS (EWD414U)
G ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
A 1 A/C Condenser Fan Motor
A 2 A/C Magnetic Clutch and Lock Sensor
A 3 A/C Triple Pressure SW
(A/C Dual and Single Pressure SW)
A 4 ABS Speed Sensor Front LH
A 5 ABS Speed Sensor Front RH
A 6 Ambient Temp. Sensor
B 1 Brake Actuator
B 2 Brake Actuator
B 3 Brake Actuator
B 4 Brake Fluid Level Warning SW
C 1 Camshaft Position Sensor
C 2 Camshaft Timing Oil Control Valve
C 3 Circuit Breaker Sensor
C 4 Converter
C 5 Converter
C 6 Crankshaft Position Sensor
D 1 DC Motor
E 1 Engine Coolant Temp. Sensor
E 2 Engine Hood Courtesy SWF 1 Front Airbag Sensor LH
F 2 Front Airbag Sensor RH
F 3 Front Parking Light LH
F 4 Front Parking Light RH
F 5 Front Side Marker Light LH
F 6 Front Side Marker Light RH
F 7 Front Turn Signal Light LH
F 8 Front Turn Signal Light RH
F 9 Front Wiper Motor
F 10 Fusible Link Block No.1
F 11 Fusible Link Block No.1
F 12 Fusible Link Block No.1
F 13 Fusible Link Block No.1
H 1 Headlight LH
H 2 Headlight RH
H 3 Heated Oxygen Sensor (Bank 1 Sensor1)
H 4 Horn
H 5 Hydraulic Booster
H 6 Hydraulic Booster

2001 PRIUS (EWD414U)
I GROUND POINT
IGCT RELAY
A/C TRIPLE
PRESSURE SW
HYDRAULIC BOOSTER
WATER PUMP MOTOR
(
A/C)
FRONT PARKING
LIGHT LH
FRONT PARKING
LIGHT RHIG2 RELAY
ENGINE HOOD
COURTESY SW
FRONT WI PER MOTOR
FRONT TURN
SIGNAL LIGHT LH
RADIATOR FAN MOTOR
ABS SOL
RELAY
INVERTER
(
GND1)
(
GND2)
PTC HEATER
BLOWER MOTOR
LINEAR CONTROLLER
(
E1)
(
SG)
(
E01)
(
E02) FRONT SIDE MARKER
LIGHT LH
FRONT SIDE MARKER
LIGHT RH
FRONT TURN
SIGNAL LIGHT RH
BRAKE FLUID LEVEL
WARNING SW
WATER TEMP. SW
DRL RELAY
IGNITION COIL AND
IGNITER NO. 1
IGNITION COIL AND
IGNITER NO. 2
IGNITION COIL AND
IGNITER NO. 3
IGNITION COIL AND
IGNITER NO. 4
ENGINE CONTROL
MODULE1K3
E 5
E 5
E 5
E 5 E 5
E 5
E 5
E 5 (
±S)
E 5
E 5
3HYDRAULIC BOOSTER E 5 E 5 (
CUT±)
E 1
E 1
E 1
E 1
E 1
E 1
3W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W± BW±B
W±B W±B W±B
W±B
W±B
W±B
W±B
W±B
W±B W±B W±B W± B W±B W± B W±B W±B W±B W±B
W±B W±B W±B W±B W±B
A
AA
(
*1)IE ECW± B
W± B
W± B
W± B
W± B
W± B W±BA
AA
A
AJUNCTION
CONNECTOR J 7
J 1
JUNCTION
CONNECTOR
W±B
A
BRAKE ECU
EAE 3 E 3 E 3
EBID214
IO114 A A
B A JUNCTION
CONNECTORB J 8 , J 9A W±B
W±B
W±B
W±B
W±B
W±BBR
BR
W±B
W±BBR BR
W±B W±B W±B
BR
ENGINE CONTROL
MODULE
ENGINE CONTROL
MODULE
(
ME01)
(
E03)DATA LINK
CONNECTOR 3 HTR RELAY
NAVIGATION ECU
RADIO AND PLAYER
IFIJ121
BR
BR
BR BR
MULTI DISPLAY (
*2)(
*2)
AIRBAG SENSOR
ASSEMBLY
COMBINATION
METER(
E1)
(
ES)
IH W±B
2B6 7
LBR
2A WATER PUMP
MOTOR (
INVERTER)
2W±B
FAN NO. 2
RELAY
AEFI RELAY

L PART NUMBER OF CONNECTORS
Code Part Name Part NumberCodePart Name Part Number
Note : Not all of the above part numbers of the connector are established for the supply.
2001 PRIUS (EWD414U) A 1
A/C Condenser Fan Motor90980±11237
A 2A/C Magnetic Clutch and Lock Sensor90980±10942
A 3A/C Triple Pressure SW (A/C Dual and
Single Pressure SW)90980±10943
A 4ABS Speed Sensor Front LH90980±11003A 5ABS Speed Sensor Front RH90980±11003
A 6Ambient Temp. Sensor90980±11070
A 7A/C Amplifier90980±11911
A 8A/C Amplifier90980±11913
A 9A/C Amplifier90980±11927
A10A/C Room Temp. Sensor
A11A/C Solar Sensor90980±11919
A12A/C Thermistor
A13Accel Position Sensor90980±11144
A14Air Inlet Control Servo Motor90980±11921
A15Air Mix Control Servo Motor90980±11909A16Air Vent Mode Control Servo Motor90980±11909
A17Airbag Sensor Assembly90980±11869
A18Airbag Sensor Assembly90980±11872
A19Airbag Sensor Assembly90980±11867
A20Airbag Squib (Front Passenger Airbag
Assembly)90980±11884
A21Airbag Squib (Steering Wheel Pad)90980±10850
A22Ashtray Illumination90980±12111
A23ABS Speed Sensor Rear LH90980±11060A24ABS Speed Sensor Rear RH90980±11060
B 1Brake Actuator90980±11087
B 2Brake Actuator90980±11161
B 3Brake Actuator90980±11698
B 4Brake Fluid Level Warning SW90980±11207
B 5Back±Up Light Relay82660±20340
B 6Blower Motor90980±10214
B 7Blower Motor Linear Controller90980±11676
B 8Body ECU90980±11971
B 9Body ECU90980±11973
B10Brake ECU90980±11935
B11Brake ECU90980±11476
B12Brake ECU90980±11637
B13Brake ECU90980±11638
B14Brake Warning Buzzer90980±10906
B15Battery Blower Motor82824±47130
B16Battery Blower Motor Controller90980±11676
B17Battery ECU90980±11392
B18Battery ECU90980±11424
B19Battery Fan Relay82660±20340
B20Buckle SW and Tension Reducer LH
B21Buckle SW RH and Seat Belt Warning
Occupant Detection Sensor90980±11471
C 1Camshaft Position Sensor90980±10947
C 2Camshaft Timing Oil Control Valve90980±11162
C 3Circuit Breaker Sensor90980±11898
C 4Converter90980±10942
C 5Converter90980±11963
C 6Crankshaft Position Sensor90980±12028
C 7Center Cluster SW90980±10801
C 8Cigarette Lighter90980±10760
C 9Cigarette Lighter Illumination90980±11148
C10Combination Meter90980±11927
C11Combination Meter90980±11923
C12Combination SW90980±11594
C13Combination SW90980±11672
C14Combination SW90980±11616
D 1DC Motor90980±10838
D 2Data Link Connector 390980±11665
D 3Daytime Running Light Relay90980±12034
D 4Diode (Door Courtesy)90980±11251
D 5Diode (Daytime Running Light)90980±10962
D 6Door Courtesy SW Front LH
D 7Door Courtesy SW Front RH90980±10871D 8Door Courtesy SW Rear LH90980±10871
D 9Door Courtesy SW Rear RH
D10Door Lock Control SW Front RH90980±10797
D11Door Lock Motor and Door Unlock
Detection SW Rear LH
90980±11150
D12Door Lock Motor and Door Unlock
Detection SW Rear RH90980±11 150
D13Door Lock Motor, Door Key Lock and
Unlock SW and Door Unlock Detection SW
Front LH
90980±11858
D14Door Lock Motor, Door Key Lock and
Unlock SW and Door Unlock Detection SW
Front RH90980±11 858
E 1Engine Coolant Temp. Sensor90980±10737
E 2Engine Hood Courtesy SW90980±11189
E 3EMPS ECU90980±12012
E 4EMPS ECU90980±11579
E 5EMPS ECU90980±12120
E 6EMPS ECU90980±11923
E 7Engine Control Module90980±11421
E 8Engine Control Module90980±11476
E 9Engine Control Module90980±11637

ENGINE ± 1NZ-FXE ENGINE
182EG20
182EG21
From Air Cleaner To Intake Air Chamber
When the Tank is Full
From Air CleanerTo Intake Air Chamber
When the Tank is EmptyVapor Reducing Fuel Tank 60

System Diagram 
Fuel Gauge
A direct-acting fuel gauge has been provided in the sub tank.
This gauge consists of a pipe that is surrounded by a coil, and a float in the pipe moves up and down with
the fluctuation of the fuel level.
A magnet is attached to the back side of the float. The up or down movement of the float causes a change
in the magnetic field. The flow of current through the coil creates a potential difference, and the resultant
voltage is transmitted to the meter ECU. For details, see page 146 (Meter Section).

THS (TOYOTA HYBRID SYSTEM)
182TH29
Rotational
Magnetic FieldU PhaseStator Coil
Rotor
Repulsion
W Phase V Phase
: From inverter
: Connected internally in the motor
Attruction
182TH09
Magnetized Side
Coil A
Coil B
Coil C Speed Sensor
(Resolver)Output Side
182TH10
Inverter Power Cable HV Battery
Junction
BlockPortion routed through
the center floorAuxiliary
Battery
Under-
the-Floor
Reinforcement
12 V
Power Cable
Voltage 
Power Cable
Voltage

34
1. Permanent Magnet Motor
When a three-phase alternating current is passed
through the three-phase windings of the stator
coil, a rotational magnetic field is created in the
electric motor. By controlling this rotating mag-
netic field according to the rotor's rotational posi-
tion and speed, the permanent magnets that are
provided in the rotor become attracted by the ro-
tating magnetic field, thus generating torque.
The generated torque is for all practical purposes
proportionate to the amount of current, and the
rotational speed is controlled by the frequency of
the alternating current.
Furthermore, a high level of torque, all the way to
high speeds, can be generated efficiently by prop-
erly controlling the rotating magnetic field and the
angles of the rotor magnets.
2. Speed Sensor (Resolver)
This is an extremely reliable and compact sensor
that precisely detects the magnetic pole position,
which is indispensable for ensuring the efficient
control of MG1 and MG2.
The sensor's stator contains 3 coils as illustrated, and
output coils B and C are electrically staggered 90 de-
grees. Because the rotor is oval, the distance of the
gap between the stator and the rotor varies with the
rotation of the rotor. Thus, by passing an alternating
current through coil A, output that corresponds to the
sensor rotor's position is generated by coils B and C.
The absolute position can then be detected from the
difference between these outputs.
In addition, the amount of positional variance
within a predetermined time is calculated by the
HV ECU, thus enabling this sensor to be used as
an rpm sensor.
3. Power Cable
The power cable is a high-voltage, high-amperage
cable that connects the HV battery with the inverter,
and the inverter with MG1 and MG2. Starting from
the connector at the left front of the HV battery lo-
cated in the luggage compartment, the power cable
is routed under the rear seat, through the floor panel,
along the under-the-floor reinforcement, and con-
nects to the inverter in the engine compartment. A
shielded cable is used for the power cable in order to
reduce electromagnetic interference.
The 12 V  wiring of the auxiliary battery also
follows the same route.
For identification purposes, the high-voltage wir-
ing harness and connectors are color-coded
orange to distinguish them from those of the ordi-
nary low-voltage wiring.

MA02G±02
MA±4
± MAINTENANCEUNDER HOOD
57 Author: Date:
2001 PRIUS (RM778U)
UNDER HOOD
GENERAL MAINTENANCE
1. GENERAL NOTES

Maintenance items may vary from country to country. Check the owner's manual supplement in which
the maintenance schedule is shown.

Every serice item in the periodic maintenance schedule must be performed.

Periodic maintenance service must be performed according to whichever interval in the periodic main-
tenance schedule occurs first, the odometer reading (miles) or the time interval (months).

Maintenance service after the last period should be performed at the same interval as before unless
otherwise noted.
2. WINDSHIELD WASHER FLUID
Check that there is sufficient fluid in the tank.
3. ENGINE COOLANT LEVEL
Check that the coolant level is between the ºFULLº and ºLOWº lines on the see±through reservoir.
4. RADIATOR AND HOSES
(a) Check that the front of the radiator is clean and not blocked with leaves, dirt or bugs.
(b) Check the hoses for cracks, kinks, rot or loose connections.
5. BRAKE FLUID LEVELS
Check that the brake fluid levels are near the upper level line on the see±through reservoirs.
6. CHECK TRANSAXLE OIL (FLUID)

Visually check the transaxle for oil (fluid) leakage.

If leakage is found, check for the cause and repair.
HINT:
Wait until the engine and motor cools down (approx. 30 min.) before checking the fluid level after extended
driving at high speeds, in hot weather, in heavy traffic or pulling a trailer.

PP26E±02
PP±50
± PREPARATIONBODY ELECTRICAL
2001 PRIUS (RM778U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
SyphonBrake fluid level warning switch
Bulb (3.4W)Fuel sender gauge, Fuel level warning switch
Dry cell batteryWireless door lock transmitter
Torque wrench
Masking tapeRear window defogger wire
Tin foilRear window defogger wire

EM1IU±03
A13907
A13908
A13934
A13943
± ENGINE MECHANICALTIMING CHAIN
EM±15
2001 PRIUS (RM778U)
REMOVAL
1. DISCONNECT BATTERY NEGATIVE (±) TERMINAL
AND HV BATTERY SERVICE PLUG
(See page HV±1)
2. REMOVE OUTER FR COWL TOP PANEL ASSEMBLY
(See page BO±32)
3. REMOVE RH ENGINE UNDER COVER
4. DRAIN ENGINE COOLANT
5. REMOVE AIR CLEANER ASSEMBLY
(a) Disconnect the MAF meter connector.
(b) Disconnect the EVAP hose from the air cleaner case.
(c) Loosen the 2 hose clamps.
(d) Remove the 3 bolts and air cleaner assembly.
6. REMOVE BRAKE RESERVOIR TANK
(a) Disconnect the brake fluid level sensor connector.
(b) Remove the 2 bolts and remove the reservoir tank and
suspend it.
(c) Remove the 3 bolts and reservoir tank bracket.
7. DISCONNECT CONNECTORS
(a) Disconnect the 4 ignition connectors.
(b) Disconnect the 4 injector connectors.
(c) Disconnect the 2 VSV connectors.
(d) Disconnect the camshaft position sensor connector.
(e) Disconnect the water temperature connector.
(f) Disconnect the Camshaft timing oil control valve connec-
tor.
8. REMOVE AIR INLET
9. REMOVE ENGINE COOLANT RESERVOIR TANK
10. REMOVE VSV FROM ENGINE MOUNTING INSULA-
TOR
11. REMOVE DRIVE BELT