2001 SUBARU FORESTER ECO mode

Doors and locks2-15
–
CONTINUED –
To unloc k all d oors (and the rear g ate), b riefly p r
ess the “UNLOCK/
DISARM ” b utton a sec ond time.
n Emergency disarming
If you c annot d isarm the system using the transmitt er (i.e. the trans-
mitter is lost, b roken or the transmitter b attery i s too weak), you c an
d isarm the system without using the transmitter.
To d isarm the system:
1. Unloc k the d oor with the key and then op en the d o or.
2. The alarm will sound .
3. Insert the key into the ig nition switc h and c yc le it from the “LOCK ”
to the “ON ” p osition three (3) times within 5 seconds.
Sounding a panic alarm
To ac tivate the alarm, keep the “LOCK/ARM ” b utton p ressed for more
than two seconds .
To d eac tivate it, p ress the “LOCK/ARM ” b utton or “UNLOCK/DISARM ”
b utton.
The p arking lig hts will also flash when the alarm i s ac tivated .
Unless a b utton on the remote is p ressed , the alarm will b e d eac ti-
vated after ap p roximately 30 sec ond s. Valet mode
When you c hoose the valet mod e, the sec urity system d oes not op er-
ate. In valet mod e, the remote transmitter is used only for loc king and
unloc king the d oors (and rear g ate) and p anic ac tiv ation.
To enter the valet mod e, op en the d river ’s d oor and keep the
“ UNLOCK/DISARM ” b utton d ep ressed for more than two seconds .
The ind ic ator lig ht rep eated ly flashes two times wh ile the system is in
valet mod e.
To exit valet mod e, op en the d river ’s d oor and keep the “UNLOCK/
DISARM ” b utton p ressed for more than two seconds. The ind ic ator
will stop flashing .

Instruments and controls3-7
–
CONTINUED –
switch is in the
“LOCK”, “ACC” or “ON” position.
To change the mode indication, briefly push the knob.
Each press of the knob changes the function in the following order.
A trip meter B trip meter
Odometer
The odometer shows the total distance that the vehicle has been driv- en. Double trip meter
The trip meter shows the distance that the vehicle has been driven
since you last set it to zero.
To set the trip meter to zero, select the indication of the A trip or B trip
meter by pushing the knob and keep the knob pushed for more than2 seconds.
NOTE If the connection between the combination meter and battery is bro-
ken for any reason such as vehicle maintenance or fuse replace-ment, the data recorded on the trip meter will be lost. Tachometer
CAUTION
Do not operate the engine with the pointer of the tachometer in
the red zone. In this range, fuel injection will be cut by the enginecontrol module to protect the engine from overrevving. The en-gine will resume running normally after the engine speed is re-duced below the red zone.
The tachometer shows the engine speed in thousands of revolutions perminute. Outside temperature indicator (if equipped)
The outside temperature indicator shows the outside temperature in a
range from –22°F to 113 °F ( –30 °C to 45 °C).

Instruments and controls3-9
–
CONTINUED –

Temperature gauge
CAUTION
If the pointer exceeds the normal operating range, safely stop the
vehicle as soon as possible.
See “ In case of emergency ” in this manual.
HS0052
Normal operating range
The temperature gauge shows engine coolant temperature when the
ignition switch is in the
“ON” position.
The coolant temperature will vary in accordance with the outside temper-
ature and driving conditions.
We recommend that you drive moderately until the pointer of the tempera-
ture gauge reaches near the middle of the range. Engine operation is opti-
mum with the engine coolant at this temperature range and high revving
operation when the engine is not warmed up enough should be avoided.
Warning and indicator lights
Several of the warning and indicator lights come on momentarily and
then go out when the ignition switch is initially turned to the “ON” posi-
tion. This permits checking the operation of the bulbs.
Apply the parking brake and turn the ignition switch to the “ON” position.
The following lights come on:

Instruments and controls3-17
–
CONTINUED –

High/low beam change (dimmer)
To change from low beam to high beam, push the turn signal lever
forward. When the headlights are on high beam, the high beam indi-cator light “a ” on the instrument panel is also on.
To switch back to low beam, pull the lever back to the detent position. Headlight flasher CAUTION
Do not hold the lever in the flashing position for more than just a few seconds.
To flash the headlights, pull the lever toward you and then release it.
The high beam will stay on for as long as you hold the lever. The
headlight flasher works even though the lighting switch is in the “OFF”
position.
When the headlights are on high beam, the high beam indicator light “ a ” on the instrment panel also comes on.
Daytime running light system (for CANADA models)
WARNING
The tail lights, parking lights, and side marker lights are not turned on by the daytime running light system. The light switchmust always be turned to the “a ” position when it is dark out-
side.
The low beam headlights will automatically come on at reduced
brightness when the engine has started, under the following condi-tions: The parking brake is fully released.
The automatic transmission selector lever is set at other than
the “P” position.
The light switch is in the “OFF” position.

3-30n
Photosensors
HB6020BA
The mirror has a photosensor attached on both the front and back
sides. If the glare from the headlights of vehicles behind you strikes
the mirror, these sensors detect it and make the reflection surface of
the mirror dimmer to help prevent you from being blinded. For this
reason, use care not to cover the sensors with stickers, or other simi-
lar items. Periodically wipe the sensors clean using a piece of dry soft
cotton cloth or an applicator. nCompass calibration
1. For optimum calibration, switch off all nonessential electrical ac-
cessories (rear window defogger, heater/air conditioning system,
spotlight, etc.) and ensure all doors are shut.
2. Drive to an open, level area away from large metallic objects or
structures and make certain the ignition switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then release, and thecompass will enter the calibration mode. “CAL” and direction will be
displayed.
4. Drive slowly in a circle until “CAL” disappears from the display
(about two or three circles).
5. The compass is now calibrated. Further calibration is not required.
The compass will automatically calibrate from this point forward.

Instruments and controls3-31
–
CONTINUED –
n
Compass zone adjustment
HB6021AB
1. The zone setting is factory preset to Zone 8. Refer to the “Com-
pass calibration zone ” map shown above or one attached to the end
of this manual to verify that the compass zone setting is correct for your geographical location.
2. Press and hold the right button for 3 seconds then release, and the
word “ZONE” will briefly appear and then the zone number will be dis-
played.
3. Press the right hand button repeatedly to cycle the display through
all possible zone settings. Stop cycling when the correct zone settingfor your location is displayed.
4. Releasing the button for 3 seconds will exit the zone setting mode.
Outside mirrors
WARNING
Objects look smaller in a convex mirror (passenger side) and far-
ther away than when viewed in a flat mirror. Do not use the con-vex mirror to judge the distances of vehicles behind you whenchanging lanes. Use the inside mirror (or glance backwards) todetermine the actual size and distance of objects that you view in
the convex mirror.

Audio5-5
–
CONTINUED –
Type A audio set (if equipped) The audio set will operate only when the ignition switch is in the “ACC” or
“ON” position.
Radio operation
HS5003BB
1 Power switch/Volume, Tone,
Balance, Fader control dial
2 AUDIO button
3 BAND button 4
Tuning buttons
5 Preset buttons
6 SCAN button
Power switch and volume/bass/treble/fader/balance control
n Power switch and volume control (PWR/VOL)
The dial 1 is used for both power (ON/OFF) and volume control. The
radio is turned ON and OFF by pushing the dial and the volume is
controlled by turning the dial. n Tone and balance control (AUDIO)
The volume control dial 1 normally functions as a volume control.
This dial becomes a control for Bass, Treble, Fader or Balance when
you select the appropriate tone and balance control mode.

5-6Choose desired volume level for each mode by turning the volume
control dial. The control function returns to volume control mode after
about 5 seconds.
To change control modes:
Each brief press of the “AUDIO” button
2 changes control modes in the following sequence starting from vol-
ume control mode. (When the radio is first turned on, the control mode
is in the volume control.)
Volume Bass Treble Fader Balance
The “AUDIO” button 2 is used for selecting the following control
modes:
Display
Control mode
HB5036BA
Turn counterclockwiseTurn clockwise
BASBass controlFor less bassFor more bass
TRETreble controlFor less trebleFor more treble
FA dFader controlTo increase rear speaker
volume and decrease front
speaker volumeTo increase front speaker
volume and decrease rear
speaker volume
BALBalance controlTo increase left speaker
volume and decrease right
speaker volumeTo increase right speakervolume and decrease left
speaker volume
VOLVolume controlFor less volumeFor more volume
Waveband selection
Push the “BAND” button 3 to select FM1, FM2 or AM reception. The
display indicates which one is currently selected.