2001 SUBARU FORESTER oil level

3-12been detected which may damage the emission control system.
To prevent serious damage to the emission control system, youshould do the following:
Reduce vehicle speed.
Avoid hard acceleration.
Avoid steep uphill grades.
Reduce the amount of cargo, if possible.
Stop towing a trailer as soon as possible.
The CHECK ENGINE warning light may stop blinking and come on
steadily after several driving trips. You should have your vehicle
checked by an authorized SUBARU dealer immediately.
Charge warning light
If this light comes on when the engine is running, it may indicate that the
charging system is not working properly. If the light comes on while driving or does not go out after the engine
starts, stop the engine at the first safe opportunity and check the alterna-
tor belt. If the belt is loose, broken or if the belt is in good condition but
the light remains on, contact your nearest SUBARU dealer immediately. Oil pressure warning light
CAUTION
Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage.
If this light comes on when the engine is running, it may indicate that the
engine oil pressure is low and the lubricating system is not working prop-
erly.If the light comes on while driving or does not go out after the engine
starts, stop the engine at the first safe opportunity and check the engine
oil level. If the oil level is low, add oil immediately. If the engine oil is at
the proper level but the light remains on, contact your nearest SUBARU
dealer immediately.

In case of emergency9-3
–
CONTINUED –

Always turn the engine off before raising the flat tire off the
ground using the jack. Never swing or push the vehicle sup- ported with the jack. The jack can come out of the jacking pointdue to a jolt and this can result in a severe accident. Do not use oil or grease on the wheel studs or nuts when the
spare tire is installed. This could cause the nuts to become looseand lead to an accident. Never place a tire or tire changing tools in the passenger
compartment after changing wheels. In a sudden stop or colli-
sions, loose equipment could strike occupants and cause injury.Store the tire and all tools in the proper place.
If you have a flat tire while d riving , never b rake sud d enly; keep d riving
straig ht ahead while g rad ually red uc ing sp eed . Then slowly p ull off the
road to a safe p lac e.
1. Park on a hard , level surfac e, whenever p ossib le, then stop the eng ine.
2. Set the p arking b rake sec urely and shift a manual transmission ve-
hic le in reverse or an automatic transmission vehic le in the “P ” (Park)
p osition.
3. Turn on the hazard warning flasher and have every one g et out of the
vehic le.
4. Put wheel b loc ks at the front and rear of the tir e d iag onally op p osite
the flat tire.
HS0148
Jacking position
Wheel blocks
5. Take out the sp are tire, jac k, and wheel nut wren c h.

9-10Make sure that the c ab les are not near any moving p
arts and that
the c ab le c lamp s are not in c ontac t with any other metal.
5. Start the eng ine of the vehic le with the b ooster b attery and run it at
mod erate sp eed . Then start the eng ine of the vehic l e that has the d is-
c harg ed b attery.
6. When finished , c arefully d isc onnec t the c ab les in exac tly the re-
verse ord er.
Engine overheating
WARNING
Never attempt to remove the radiator cap until the engine hasbeen shut off and has fully cooled down. When the engine is hot,the coolant is under pressure. Removing the cap while the engineis still hot could release a spray of boiling hot coolant, which
could burn you very seriously.
If the eng ine overheats, safely p ull off the road a nd stop the vehic le in a
safe p lac e.
If steam is coming from the engine compartment
Turn the eng ine off and g et everyone away from the vehic le until it
c ools d own. If no steam is coming from the engine compartment
1. Keep the eng ine running at id ling sp eed .
2. Op en the hood to ventilate the eng ine c omp artment .
Confirm that the c ooling fan is turning . If the fan is not turning , im-
med iately turn the eng ine off and c ontac t your auth orized d ealer for
rep air.
3. After the eng ine c oolant temp erature has d rop p ed , turn off the en-
g ine.
If the temp erature g aug e stays at the overheated zo ne, turn the en-
g ine off.
4. After the eng ine has fully c ooled d own, c hec k the c oolant level in

9-14CAUTION
If transmission failure occurs, transport your vehicle on a flat-
bed truck. For AWD vehicles, the traveling speed must be limited to less
than 20 mph (30 km/h) and the traveling distance to less than 31
miles (50 km). For greater speeds and distances, transport your
vehicle on a flat-bed truck.
HS0163
We d o not rec ommend this method of towing . Use this method only
when towing servic e b y a SUBARU d ealer or a c ommerc ial towing
servic e is not availab le.
1. Chec k the transmission and d ifferential oil level s and ad d oil to
b ring it to the up p er level if nec essary.
2. Release the p arking b rake and p ut the transmissio n in neutral.
3. The ig nition switc h should b e in the “ACC ” p osition while the ve-
hic le is b eing towed .
4. Take up slac k in the towline slowly to p revent d a mag e to the ve-
hic le.

11-8Engine compartment overview 1
Manual transmission oil level
g aug e (MT) (p ag e 11-21) or
Differential g ear oil level
g aug e (AT) (p ag e 11-24)
2 Air c leaner element
(p ag e 11-18)
3 Clutc h fluid reservoir
(p ag e 11-30)
4 Automatic transmission fluid
level g aug e (p ag e 11-22)
5 Brake fluid reservoir
(p ag e 11-28)
6 Fuel filter 7
Wind shield washer tank
(p ag e 11-33)
8 Fuse b ox (p ag e 11-44)
9 Battery (p ag e 11-31)
Q Eng ine oil filler c ap
(p ag e 11-9)
W Eng ine c oolant reservoir
(p ag e 11-15)
E Eng ine oil level g aug e
(p ag e 11-9)
R Power steering fluid reservoir
(p ag e 11-27)
T Rad iator c ap (p ag e 11-15) HGA017BB

Maintenance and service11-9
–
CONTINUED –
Engine oil
Checking the oil level
Chec k the eng ine oil level at eac h fuel stop .
OM-H2727
HS0173
Upper level
Lower- level Notch
front
1. Park the vehic le on a level surfac e and stop the eng ine.
2. Pull out the d ip stic k, wip e it c lean, and insert it ag ain.
3. Be sure the d ip stic k is c orrec tly inserted until it stop s with the
g rap hic symb ol on its top ap p earing as shown in the illustra-
tion.
4. Pull out the d ip stic k ag ain and c hec k the oil lev el on it. If it is b elow
the lower level, ad d oil to b ring the level up to t he up p er level.
CAUTION
Use only engine oil with the recommended grade and viscosity.
If you c hec k the oil level just after stop p ing the eng ine, wait a few min-
utes for the oil to d rain b ac k into the oil p an b ef ore c hec king the level.
Just after d riving or while the eng ine is warm, the eng ine oil level
read ing may b e in a rang e b etween the up p er level a nd the notc h
mark. This is c aused b y thermal exp ansion of the en g ine oil.
To p revent overfilling the eng ine oil, d o not ad d a ny ad d itional oil
ab ove the up p er level when the eng ine is c old .

11-10
Changing the oil and oil filter
Chang e the oil and oil filter ac c ord ing to the main tenanc e sc hed ule in
the “Warranty and Maintenanc e Booklet ”.
The eng ine oil and oil filter must b e c hang ed more freq uently than
listed in the maintenanc e sc hed ule when d riving on d usty road s,
when short trip s are freq uently mad e when towing a trailer, or when
d riving in extremely c old whether.
1. Warm up the eng ine b y letting the eng ine id le for ab out 10 minutes
to ease d raining the eng ine oil.
2. Park the vehic le on a level surfac e and stop the eng ine.
3. Remove the oil filler c ap .
HS0174
Drain plug
4. Drain out the eng ine oil b y removing the d rain p l ug while the en-
g ine is still warm. The used oil should b e d rained into an ap p rop riate
c ontainer and d isp osed of p rop erly.
WARNING
Be careful not to burn yourself with hot engine oil.
5. Wip e the seating surfac e of the d rain p lug with a c lean c loth and
tig hten it sec urely with a new sealing washer after the oil has c om-
p letely d rained out.

Maintenance and service11-11
–
CONTINUED –
HS0176
HS0175
Drain plugSealing washer
Oil filter
6. Remove the und er c over.
7. Remove the oil filter with an oil filter wrenc h.
8. Before installing a new oil filter, ap p ly a thin c oat of eng ine oil to the
seal.
9. Clean the rub b er seal seating area of the lower c rank c ase and
install the oil filter b y hand turning . Be c areful not to twist or d amag e
the seal.
10. Tig hten it ap p roximately two-third s of a turn af ter the seal makes
c ontac t with und ersid e of the c rank c ase.
CAUTION
Never over tighten the oil filter because that can result in an oilleak.
11. Reinstall the und er c over.
12. Pour the sp ec ified amount of eng ine oil throug h the filler nec k.
Oil c ap ac ity: 4.2 US q t (4.0 liters, 3.5 Imp q t)
13. Start the eng ine and make sure that no oil leaks ap p ear around
the filter ’s rub b er seal.
14. Run the eng ine until it reac hes the normal op era ting temp erature.
Then stop the eng ine and wait a few minutes to allo w the oil d rain
b ac k. Chec k the oil level ag ain and if nec essary, a d d more eng ine oil.