2001 SUBARU FORESTER light

10-2Exterior care
Washing
CAUTION
When washing the vehicle, the brakes may get wet. As a result,
the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brakepedal to heat up the brakes. Do not wash the engine compartment and areas adjacent to it.
If water enters the engine air intake, electrical parts or the power
steering fluid reservoir, it will cause engine trouble or faulty pow-
er steering respectively.
The b est way to p reserve your vehic le ’s b eauty is freq uent washing .
Wash the vehic le at least onc e a month to avoid c on tamination b y road
g rime.
Wash d irt off with a wet sp ong e and p lenty of lukew arm or c old water. Do
not wash the vehic le with hot water and in d irec t s unlig ht.
Salt, c hemic als, insec ts, tar, soot and b ird d rop p i ng s should b e washed
off b y using a lig ht d eterg ent, as req uired . If you use a lig ht d eterg ent,
make c ertain that it is a neutral d eterg ent. Do not use strong soap or
c hemic al d eterg ents. All c leaning ag ents should b e p romp tly flushed
from the surfac e and not allowed to d ry there. Rins e the vehic le thor-
oug hly with p lenty of lukewarm water. Wip e the rema ining water off with a
c hamois or soft c loth.
Washing the underbody
Chemic als, salts and g ravel used for d eic ing road s urfac es are ex-
tremely c orrosive, ac c elerating the c orrosion of un d erb od y c omp o-
nents, suc h as the exhaust system, fuel and b rake l ines, b rake
c ab les, floor p an and fend ers, and susp ension.
Thoroug hly flush the und erb od y and insid e of the fe nd ers with luke-
warm or c old water at freq uent intervals to red uc e the harmful effec ts
of suc h ag ents.

10-4
Do not use soap c ontaining g rit to c lean the wheels . Be sure to use a
neutral c leaning ag ent, and later rinse thoroug hly with water. Do not
c lean the wheels with a stiff b rush or exp ose them to a hig h-sp eed wash-
ing d evic e. Clean the vehic le (inc lud ing the aluminum wheels) w ith water as soon
as p ossib le when it has b een sp lashed with sea wate r, exp osed to sea
b reezes, or d riven on road s treated with salt or ot her ag ents.
Cleaning fog light lens
If the fog lig ht p rotec tor oug ht to b e removed for c leaning the fog lig ht
lens, follow then the instruc tion g iven in “Fog lig ht ” sec tion (Rep lac ing
b ulb s) und er Chap ter 11.
When c leaning the fog lig ht lens, p ark the vehic le on a safe p lac e, stop
the eng ine and c onfirm that the fog lig ht lens is n ot hot b efore p roc eed -
ing with the work.
Corrosion protection
Your SUBARU has b een d esig ned and b uilt to resist c orrosion. Sp ec ial
materials and p rotec tive finishes have b een used on most p arts of the
vehic le to help maintain fine ap p earanc e, streng th, and reliab le op era-
tion.
Most common causes of corrosion
The most c ommon c auses of c orrosion are:
1. The ac c umulation of moisture retaining d irt and d eb ris in b od y
p anel sec tions, c avities, and other areas.
2. Damag e to p aint and other p rotec tive c oating s c au sed b y g ravel
and stone c hip s or minor ac c id ents.
Corrosion is ac c elerated on the vehic le when:
1. It is exp osed to road salt or d ust c ontrol c hemic als, or used in
c oastal areas where there is more salt in the air, or in areas where
there is c onsid erab le ind ustrial p ollution.
2. It is d riven in areas of hig h humid ity, esp ec iall y when temp eratures
rang e just ab ove freezing .

11-2Headlight
11-49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fog light (if equipped) 11-50
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front turn signal, parking light and front side marker light 11-51 . . . . .
Rear combination lights 11-52
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
License plate light 11-53
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior light and luggage compartment light 11-54 . . . . . . . . . . . . . . . . . . . . . .
Spot light 11-55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High mount stop light 11-55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance and service11-31
–
CONTINUED –

Recommended clutch fluid
FMVSS No. 116, fresh DOT 3 or 4 brake fluid
Brake booster
If the b rake b ooster d oes not op erate as d esc rib ed b elow, have it
c hec ked b y your SUBARU d ealer.
1. With the eng ine off, d ep ress the b rake p ed al seve ral times, ap p lying
the same p ed al forc e eac h time. The d istanc e the p e d al travels should
not vary.
2. With the b rake p ed al d ep ressed , start the eng ine. The p ed al should
move slig htly d own to the floor.
3. With the b rake p ed al d ep ressed , stop the eng ine a nd keep the p ed al
d ep ressed for 30 sec ond s. The p ed al heig ht should n ot c hang e.
4. Start the eng ine ag ain and run for ab out one minu te then turn it off.
Dep ress the b rake p ed al several times to c hec k the b rake b ooster.
Brake b ooster op erates p rop erly if the p ed al stroke d ec reases with eac h
d ep ression. Battery
WARNING
Before beginning work on or near any battery, be sure to extin-
guish all cigarettes, matches, and lighters. Never expose a bat- tery to an open flame or electric sparks. Batteries give off a gaswhich is highly flammable and explosive. For safety, in case an explosion does occur, wear eye protec-
tion or shield your eyes when working near any battery. Never
lean over a battery. Do not let battery fluid contact eyes, skin, fabrics, or paint be-
cause battery fluid is a corrosive acid. If battery fluid gets on yourskin or in your eyes, immediately flush the area with water thor-
oughly. Seek medical help immediately if acid has entered the

Maintenance and service11-49
–
CONTINUED –

Headlight
CAUTION
Halogen headlight bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, fingerprints or grease on the bulb surface develop into hot spots, caus-ing the bulb to break. If there are finger prints or grease on thebulb surface, wipe them away with a soft cloth moistened with al-cohol.
NOTE If headlight aiming is required, consult your SUBARU dealer for proper adjustment of the headlight aim.
HS0327
HS0328
Rubber cover
Electrical connector
Top markBulb
Retainer spring
1. Disc onnec t the elec tric al c onnec tor, then remove the rub b er c over.
2. Remove the retainer sp ring .
3. Rep lac e the b ulb , then set the retainer sp ring se c urely.
4. Install the rub b er c over with the top mark fac ing up , then rec onnec t
the elec tric al c onnec tor.

11-50
Fog light (if equipped)
CAUTION
Halogen light bulbs become very hot while in use. If you touch the bulb surface with bare hands or greasy gloves, finger prints
or grease on the bulb surface develop into hot spots, causing thebulb to break. If there are finger prints or grease on the bulb sur-face, wipe them away with a soft cloth moistened with alcohol.
To remove and install the fog light protector
HS0214
HS02131
2
1. Unhook the lower p art of the fog lig ht p rotec tor b y p ulling the hook
d own.
2. Pull the p rotec tor to remove it.
3. To install the p rotec tor, first insert the up p er p art of the p rotec tor
into the g ap b etween the fog lig ht and b od y, then p ush the lower p art
of the p rotec tor until it c lic ks.
4. Make sure that the p rotec tor is loc ked in p lac e b y p ulling it lig htly.

Maintenance and service11-51
–
CONTINUED –

Bulb replacement
HS0216
HS0215
Bulb
1. Remove the fog lig ht p rotec tor.
2. Remove the fog lig ht assemb ly b y removing the two sc rews.
3. Disc onnec t the c onnec tor.
4. Remove the fog lig ht b ulb b y turning it c ounterc l oc kwise.
5. Rep lac e the b ulb with a new one. Then rec onnec t t he c onnec tors
and reinstall the removed p arts in the reverse ord e r of removal.
Front turn signal, parking light and front side marker light
HS0217
1. Remove the front turn sig nal lig ht assemb ly mount ing sc rew loc ated
at the top of the head lig ht assemb ly using a p hilli p s sc rewd river.
2. Move the front turn sig nal lig ht assemb ly forward until it p op s out from

11-52the fend er.
3. Remove the b ulb hold er from the front turn sig nal
lig ht assemb ly b y
turning it c ounterc loc kwise.
4. Pull the b ulb out of the soc ket. Install a new b u lb .
5. Set the b ulb hold er into the front turn sig nal li g ht assemb ly and turn it
c loc kwise until it loc ks.
6. Set the front turn sig nal lig ht assemb ly into the fend er. Tig hten the
mounting sc rew. Rear combination lights Brake/tail and rear turn signal light
HS0219
HS0218
1. Unlatc h the rear c omb ination lig ht c over b y p ulli ng the knob . Op en
the c over up .
2. Remove the b ulb hold er from the rear c omb ination lig ht assemb ly
b y turning it c ounterc loc kwise.
3. Remove the b ulb from the soc ket b y p ushing it and turning c oun-
terc loc kwise. Install a new b ulb .
4. Set the b ulb hold er into the rear c omb ination lig ht assemb ly and
turn it c loc kwise until it loc ks.
5. Close the c over and latc h the loc k.