2001 SUBARU FORESTER flat tire

9-2
Hazard warning flasher
HS0053
The hazard warning flasher should b e used in d ay or
nig ht to warn other
d rivers when you have to p ark your vehic le und er em erg enc y c ond itions.
Avoid stop p ing on the road . It is b est to safely p u ll off the road if a p rob -
lem oc c urs.
The hazard warning flasher c an b e ac tivated reg ard l ess of the ig nition
switc h p osition.
Turn on the hazard warning b y p ushing the hazard wa rning flasher
switc h. Turn it off b y p ushing the switc h ag ain. NOTE When the hazard warning flasher is on, the turn signals do not work.
Flat tires
WARNING
Do not jack up the vehicle on an incline or a loose road sur-
face. The jack can come out of the jacking point or sink into the ground and this can result in a severe accident. Use only the jack provided with your vehicle. The jack sup-
plied with the vehicle is designed only for changing a tire. Neverget under the vehicle while supporting the vehicle with this jack.

In case of emergency9-3
–
CONTINUED –

Always turn the engine off before raising the flat tire off the
ground using the jack. Never swing or push the vehicle sup- ported with the jack. The jack can come out of the jacking pointdue to a jolt and this can result in a severe accident. Do not use oil or grease on the wheel studs or nuts when the
spare tire is installed. This could cause the nuts to become looseand lead to an accident. Never place a tire or tire changing tools in the passenger
compartment after changing wheels. In a sudden stop or colli-
sions, loose equipment could strike occupants and cause injury.Store the tire and all tools in the proper place.
If you have a flat tire while d riving , never b rake sud d enly; keep d riving
straig ht ahead while g rad ually red uc ing sp eed . Then slowly p ull off the
road to a safe p lac e.
1. Park on a hard , level surfac e, whenever p ossib le, then stop the eng ine.
2. Set the p arking b rake sec urely and shift a manual transmission ve-
hic le in reverse or an automatic transmission vehic le in the “P ” (Park)
p osition.
3. Turn on the hazard warning flasher and have every one g et out of the
vehic le.
4. Put wheel b loc ks at the front and rear of the tir e d iag onally op p osite
the flat tire.
HS0148
Jacking position
Wheel blocks
5. Take out the sp are tire, jac k, and wheel nut wren c h.

In case of emergency9-5
–
CONTINUED –
HS0149
7. Plac e the jac k und er the sid e sill at the front o r rear jac k-up p oint c los-
est to the flat tire.
Turn the jac ksc rew b y hand until the jac k head eng a g es firmly into the
jac k-up p oint.
HS0150
8. Insert the jac k hand le into the jac ksc rew, and tu rn the hand le c loc k-
wise until the tire c lears the g round . Do not raise the vehic le hig her than
nec essary.

9-6
HS0151
9. Remove the wheel nuts and the flat tire.
10. Before p utting the sp are tire on, c lean the mounting surfac e of the
wheel and hub with a c loth.
HG0104
OM-H0172
11. Put on the sp are tire. Rep lac e the wheel nuts. T ig hten them b y hand .
12. Turn the jac k hand le c ounterc loc kwise to lower t he vehic le.
13. Use the wheel nut wrenc h to sec urely tig hten the wheel nuts to the
sp ec ified torq ue, following the tig htening ord er in the illustration.

In case of emergency9-7
–
CONTINUED –
HS0152
14
2
53
The torq ue for tig htening the nuts is 58 to 72 ft-l b (78 to 98 N-m, 8 to 10
kg -m). This torq ue is eq uivalent to ap p lying ab out 88 to 110 lb s (40 to 50
kg ) at the top of the wheel nut wrenc h. Never use y our foot on the wheel
nut wrenc h or a p ip e extension on the wrenc h b ec aus e you may exc eed
the sp ec ified torq ue. Have the wheel nut torq ue c he c ked at the nearest
automotive servic e fac ility.
14. Store the flat tire in the sp are tire c omp artmen t.
HS0153
Flat tireAttaching bolt
Spacer
Also store the jac k and wheel nut wrenc h in their s torag e loc ations.

In case of emergency9-17
–
CONTINUED –

Jack and jack handle
HS0160
HS0118
The jac k is stored und er the left sid e of the c arg o floor.
The jac k hand le is stored und er the lid .
For how to use the jac k, refer to “Flat tires ”.

Maintenance and service11-43
–
CONTINUED –
OM-H0231
New tread Worn tread
HS0201
Tread wear indicator
A tire should b e rep lac ed when the tread wear ind ic ator ap p ears as a
solid b and ac ross the tread . The ind ic ators ap p ear when the remaining
tread has b een worn to 0.063 in (1.6 mm) or less. NOTE When any of the wheels is removed and replaced for tire rotation or to change a flat tire, always check the tightness of the wheel nutsafter driving approximately 600 miles (1,000 km). If any nut is loose,tighten it to the specified torque.
Aluminum wheels (If equipped)
Aluminum wheels c an b e sc ratc hed and d amag ed easily . Hand le them
c arefully to maintain their ap p earanc e, p erformanc e , and safety.
When any of the wheels is removed and rep lac ed for tire rotation or to
c hang e a flat, always c hec k the tig htness of the wh eel nuts after d riving
ap p roximatly 600 miles (1,000 km). If any nut is lo ose, tig hten it to the
sp ec ified torq ue. Never ap p ly oil to the thread ed p arts, wheel nuts, or tap ered surfac e
of the wheel. Never let the wheel rub ag ainst sharp p rotrusions o r c urb s.
Be sure to fit tire c hains on uniformly and c omp let ely around the tire,
otherwise the c hains may sc ratc h the wheel. When wheel nuts, b alanc e weig hts, or the c enter c ap are rep lac ed ,

12-8Vehicle identification
HS0226
Vehicle identification number
Emission
control label
Vehicle identification number plate
Tire inflation pressure label
Model number plate Bar cord label
Vacuum hose piping label
Certification plate