2001 NISSAN X-TRAIL ad blue

HOW TO USE THIS MANUAL
GI-17
C
D
E
F
G
H
I
J
K
L
MB
GI
14 Wire color
●This shows a code for the color of the wire.
B = Black
W = White
R = Red
G = Green
L = Blue
Y = Yellow
LG = Light GreenBR = Brown
OR or O = Orange
P = Pink
PU or V (Violet) = Purple
GY or GR = Gray
SB = Sky Blue
CH = Dark Brown
DG = Dark Green
When the wire color is striped, the base color is given first, followed by the stripe color as shown
below:
Example: L/W = Blue with White Stripe
15 Option description
●This shows a description of the option abbreviation used on the page.
16 Switch
●This shows that continuity exists between terminals 1 and 2 when the switch is in the A posi-
tion. Continuity exists between terminals 1 and 3 when the switch is in the B position.
17 Assembly parts
●Connector terminal in component shows that it is a harness incorporated assembly.
18 Cell code
●This identifies each page of the wiring diagram by section, system and wiring diagram page
number.
19 Current flow arrow
●Arrow indicates electric current flow, especially where the direction of standard flow (vertically
downward or horizontally from left to right) is difficult to follow.
●A double arrow “ ” shows that current can flow in either direction depending on cir-
cuit operation.
20 System branch
●This shows that the system branches to another system identified by cell code (section and
system).
21 Page crossing
●This arrow shows that the circuit continues to another page identified by cell code.
●The C will match with the C on another page within the system other than the next or preced-
ing pages.
22 Shielded line
●The line enclosed by broken line circle shows shield wire.
23Component box in
wave line
●This shows that another part of the component is also shown on another page (indicated by
wave line) within the system.
24 Component name
●This shows the name of a component.
25 Connector number
●This shows the connector number.
●The letter shows which harness the connector is located in.
●Example: M : main harness. For detail and to locate the connector, refer to PG section "Main
Harness", “Harness Layout”. A coordinate grid is included for complex harnesses to aid in
locating connectors.
26 Ground (GND)
●The line spliced and grounded under wire color shows that ground line is spliced at the
grounded connector.
27 Ground (GND)
●This shows the ground connection. For detailed ground distribution information, refer to
"Ground Distribution" in PG section.
28 Connector views
●This area shows the connector faces of the components in the wiring diagram on the page.
29 Common component
●Connectors enclosed in broken line show that these connectors belong to the same compo-
nent.
30 Connector color
●This shows a code for the color of the connector. For code meaning, refer to wire color codes,
Number 14 of this chart.
31Fusible link and fuse
box
●This shows the arrangement of fusible link(s) and fuse(s), used for connector views of
"POWER SUPPLY ROUTING" in PG section.
The open square shows current flow in, and the shaded square shows current flow out.
32 Reference area
●This shows that more information on the Super Multiple Junction (SMJ) and Joint Connectors
(J/C) exists on the PG section. Refer to "Reference Area" for details. Num-
berItem Description

EM-64
[QR]
CYLINDER HEAD
5. Install valve spring.
●Install smaller pitch (valve spring seat side) to cylinder head
side.
●Confirm identification color of valve spring.
6. Install valve spring retainer.
7. Install valve collet.
●Compress valve spring with valve spring compressor. Install
valve collet with magnet hand.
●Tap stem edge lightly with plastic hammer after installation to check its installed condition.
8. Install valve lifter.
9. Install spark plug tube.
●Press fit it into cylinder head as follows.
a. Remove old liquid gasket from cylinder head side mounting
hole.
b. Apply liquid gasket all round on spark plug tube with a 12 mm
(0.47 in) width from edge of spark plug tube on the press fit side.
Use Genuine Liquid gasket or equivalent.
c. Using a drift (commercial service tool), press fit spark plug tube
so that height is as same as H shown in figure.
CAUTION:
●When press fitting be careful not to deform spark plug tube.
●After press fitting, wipe off any protruding liquid gasket on top surface of cylinder head.
10. Install spark plug with spark plug wrench.
Inspection After DisassemblyEBS00KNS
CYLINDER HEAD DISTORTION
1. Wipe off engine oil and remove water scale (like deposit), gas-
ket, sealer, carbon, etc with scraper.
CAUTION:
Use utmost care not to allow gasket debris to enter pas-
sages for engine oil or water.
2. At each of several locations on bottom surface of cylinder head,
measure distortion in six directions.
VALVE DIMENSIONS
Check dimensions of each valve. For dimensions, refer to SDS, EM-
99, "Valve Dimensions" . Intake : Blue
Exhaust : Yellow
Press fit height “H” standard value:
38.55 - 38.65 mm (1.518 - 1.522 in)
PBIC0525E
SBIA0252E
Standard: 0.1mm (0.004 in)
PBIC0075E
SEM188A

EM-66
[QR]
CYLINDER HEAD
5. Press valve guide from camshaft side to dimensions as in illus-
tration.
CAUTION:
Cylinder head contains heat, when working, wear protective
equipment to avoid getting burned.
6. Using valve guide reamer, apply reamer finish to valve guide.
VALVE SEAT CONTACT
●After confirming that the dimensions of valve guides and valves
are within specifications, perform this procedure.
●Apply prussian blue (or white lead) onto contacting surface of
valve seat to check the condition of the valve contact on the sur-
face.
●Check if the contact area band is continuous all around the cir-
cumference.
●If not, grind to adjust valve fitting and check again. If the contact-
ing surface still has NG conditions even after the re-check,
replace valve seat.
VALVE SEAT REPLACEMENT
When valve seat is removed, replace with oversized [0.5 mm (0.020 in)] valve seat.
1. Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess
in cylinder head. Set the machine depth stop to ensure this.
2. Ream cylinder head recess diameter for service valve seat.
●Be sure to ream in circles concentric to the valve guide center.
This will enable valve seat to fit correctly.
PBIC0078E
Standard
Intake and exhaust:
6.000 - 6.018 mm (0.2362 - 0.2369 in)
SEM932C
SBIA0322E
Oversize [0.5 mm (0.020 in)]
Intake : 37.000 - 37.016 mm (1.4567 - 1.4573 in)
Exhaust : 32.000 - 32.016 mm (1.2598 - 1.2605 in)
SEM795A

EM-68
[QR]
CYLINDER HEAD
VALVE SPRING DIMENSIONS AND VALVE SPRING PRESSURE LOAD
Check valve spring pressure with valve spring seat installed at spec-
ified spring height.
CAUTION:
Do not remove valve spring seat.
SEM113
Standard: INTAKE EXHAUST
Free height : 44.84 - 45.34 mm (1.7654 -
1.7850 in): 45.28 - 45.78 mm (1.7827 -
1.8024 in)
Installation height : 35.30 mm (1.390 in) : 35.30 mm (1.390 in)
Installation load : 151 - 175 N (15.4 - 17.8 kg, 34 -
39 lb): 151 - 175 N (15.4 - 17.8 kg, 34 -
39 lb)
Height during valve open : 24.94 mm (0.9819 in) : 26.39 mm (1.0390 in)
Load with valve open : 358 - 408 N (36.5 - 41.6 kg, 80 -
92 lb): 325 - 371 N (33.1 - 37.8 kg, 73 -
83 lb)
Identification color : Blue : Yellow

CYLINDER BLOCK
EM-87
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM
Main Bearing Selection Table (No. 2 and 4 journals)
Main Bearing Grade Table (All Journals)
Unit: mm (in)
KBIA0150E
Grade number Thickness Identification color
(UPR / LWR)Remarks
0 1.973 - 1.976 (0.0777 - 0.0778) Black
Grade and color are the same
for upper and lower bearings. 1 1.976 - 1.979 (0.0778 - 0.0779) Brown
2 1.979 - 1.982 (0.0779- 0.0780) Green
3 1.982 - 1.985 (0.0780 - 0.0781) Yellow
4 1.985 - 1.988 (0.0781 - 0.0783) Blue
5 1.988 - 1.991 (0.0783 - 0.0784) Pink
6 1.991 - 1.994 (0.0784 - 0.0785) Purple
7 1.994 - 1.997 (0.0785 - 0.0786) White

EM-88
[QR]
CYLINDER BLOCK
Use Undersize Bearing Usage Guide
●Use undersize (US) bearing when oil clearance with standard size main bearing is not within specification.
●When using undersize (US) bearing, measure the bearing inner diameter with bearing installed, and grind
journal until oil clearance falls within specification.
Bearing undersize table
Unit: mm (in)
CAUTION:
Keep fillet R when grinding crankshaft journal in order to use
underseas bearing (All journals).
Inspection After DisassemblyEBS00KNW
CRANKSHAFT END PLAY
●Using dial indicator, measure crankshaft travel amount by mov-
ing the crankshaft forward or backward.
●If the measured value exceeds the limit, replace the thrust bear-
ings, and measure again. If it still exceeds the limit, replace the
crankshaft also.
01UPR 1.973 - 1.976 (0.0777 - 0.0778)
Black / Brown
Grade and color are different
for upper and lower bearings. LWR 1.976 - 1.979 (0.0778 - 0.0779)
12UPR 1.976 - 1.979 (0.0778 - 0.0779)
Brown / Green
LWR 1.979 - 1.982 (0.0779 - 0.0780)
23UPR 1.979 - 1.982 (0.0779- 0.0780)
Green / Yellow
LWR 1.982 - 1.985 (0.0780 - 0.0781)
34UPR 1.982 - 1.985 (0.0780 - 0.0781)
Yellow / Blue
LWR 1.985 - 1.988 (0.0781 - 0.0783)
45UPR 1.985 - 1.988 (0.0781 - 0.0783)
Blue / Pink
LWR 1.988 - 1.991 (0.0783 - 0.0784)
56UPR 1.988 - 1.991 (0.0783 - 0.0784)
Pink / Purple
LWR 1.991 - 1.994 (0.0784 - 0.0785)
67UPR 1.991 - 1.994 (0.0784 - 0.0785)
Purple / White
LWR 1.994 - 1.997 (0.0785 - 0.0786) Grade number Thickness Identification color
(UPR / LWR)Remarks
Size Thickness
US 0.25 (0.0098) 2.106 - 2.114 (0.0829 - 0.0832)
KBIA0148E
Standard : 0.10 - 0.26 mm (0.0039 - 0.0102 in)
Limit : 0.30 mm (0.0118 in)
PBIC0268E

SERVICE DATA AND SPECIFICATIONS (SDS)
EM-107
[QR]
C
D
E
F
G
H
I
J
K
L
MA
EM
Undersize
Unit: mm (in)
Bearing Oil Clearance
Unit: mm (in)
CONNECTING ROD BEARING
Undersize
Unit: mm (in) 0 1.973 - 1.976 (0.0777 - 0.0778) Black
Grade and color are the same
for upper and lower bearings. 1 1.976 - 1.979 (0.0778 - 0.0779) Brown
2 1.979 - 1.982 (0.0779 - 0.0780) Green
3 1.982 - 1.985 (0.0780 - 0.0781) Yellow
4 1.985 - 1.988 (0.0781 - 0.0783) Blue
5 1.988 - 1.991 (0.0783 - 0.0784) Pink
6 1.991 - 1.994 (0.0784 - 0.0785) Purple
7 1.994 - 1.997 (0.0785 - 0.0786) White
01UPR 1.973 - 1.976 (0.0777 - 0.0778)
Black / Brown
Grade and color are different
for upper and lower bearings. LWR 1.976 - 1.979 (0.0778 - 0.0779)
12UPR 1.976 - 1.979 (0.0778 - 0.0779)
Brown / Green
LWR 1.979 - 1.982 (0.0779 - 0.0780)
23UPR 1.979 - 1.982 (0.0779 - 0.0780)
Green / Yellow
LWR 1.982 - 1.985 (0.0780 - 0.0781)
34UPR 1.982 - 1.985 (0.0780 - 0.0781)
Yellow / Blue
LWR 1.985 - 1.988 (0.0781 - 0.0783)
45UPR 1.985 - 1.988 (0.0781 - 0.0783)
Blue / Pink
LWR 1.988 - 1.991 (0.0783 - 0.0784)
56UPR 1.988 - 1.991 (0.0783 - 0.0784)
Pink / Purple
LWR 1.991 - 1.994 (0.0784 - 0.0785)
67UPR 1.991 - 1.994 (0.0784 - 0.0785)
Purple / White
LWR 1.994 - 1.997 (0.0785 - 0.0786)
Item Thickness Main journal diameter
US 0.25 (0.0098) 2.106 - 2.114 (0.0829 - 0.0832) Grind so that bearing clearance is the specified value.
Main bearing oil clearanceStandardNo. 1, 3 and 5 0.012 - 0.022 (0.0005 - 0.0009)
No. 2 and 4 0.018 - 0.028 (0.0007 - 0.0011)
Limit 0.1 (0.004)
Grade number Thickness mm (in) Identification color (mark)
0 1.499 - 1.495 (0.0590 - 0.0589) Black
1 1.503 - 1.499 (0.0592 - 0.0590) Brown
2 1.507 - 1.503 (0.0593 - 0.0592) Green
3 1.511 - 1.507 (0.0595 - 0.0593) Yellow
Item Thickness Crank pin journal diameter
US 0.25 (0.0098) 1.624 - 1.632 (0.0639 - 0.0643) Grind so that bearing clearance is the specified value.

CYLINDER BLOCK
EM-209
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
EM
When Re-using Removed Cylinder Block and Crankshaft
1. Measure the inner diameter of cylinder block main bearing hous-
ing.
2. Locate the applicable cell where the measurement falls, on
“Inner diameter of Cylinder block main bearing housing” row on
the table.
3. Measure the outer diameter of the crankshaft journal.
4. Locate the applicable cell where the measurement falls, under
“Crankshaft journal outer diameter” column on the table.
5. The main bearing to be used (STD 0 to STD 4) can be located in
the cell where the row and column cross.
Main Bearing Grade Table
Unit: mm (in)
Under Size Bearing Usage
●If bearing clearance is out of specifications for main bearings in standard size, use under size bearings.
●When using under size bearings, measure bearing inner diameter with bearing installed, and grind crank-
shaft journals to adjust clearance to specification.
JEM215G
Inner diameter of Cylinder block main bearing housing66.654 - 66.663
(2.6242 - 2.6245)66.663 - 66.672
(2.6245 - 2.6249)66.672 - 66.681
(2.6249 - 2.6252)
Crankshaft journal
outer diameterGrade
(punched)012
62.967 - 62.975
(2.4790 - 2.4793)0
●Bearing grade No.
●Bearing thickness
●Oil clearance
●Identification colorSTD 0
1.816 - 1.820
(0.0715 - 0.0717)
0.039 - 0.066
(0.0015 - 0.0026)
BlackSTD 1
1.820 - 1.824
(0.0717 - 0.0718)
0.039 - 0.066
(0.0015 - 0.0026)
BrownSTD 2
1.824 - 1.828
(0.0718 - 0.0720)
0.039 - 0.066
(0.0015 - 0.0026)
Green
62.959 - 62.967
(2.4787 - 2.6790)1
●Bearing grade No.
●Bearing thickness
●Oil clearance
●Identification colorSTD 1
1.820 - 1.824
(0.0717 - 0.0718)
0.039 - 0.066
(0.0015 - 0.0026)
BrownSTD 2
1.824 - 1.828
(0.0718 - 0.0720)
0.039 - 0.066
(0.0015 - 0.0026)
GreenSTD 3
1.828 - 1.832
(0.0720 - 0.0721)
0.039 - 0.066
(0.0015 - 0.0026)
Ye l l o w
62.951 - 62.959
(2.4784 - 2.4787)2
●Bearing grade No.
●Bearing thickness
●Oil clearance
●Identification colorSTD 2
1.824 - 1.828
(0.0718 - 0.0720)
0.039 - 0.066
(0.0015 - 0.0026)
GreenSTD 3
1.828 - 1.832
(0.0720 - 0.0721)
0.039 - 0.066
(0.0015 - 0.0026)
Ye l l o wSTD 4
1.832 - 1.836
(0.0721 - 0.0723)
0.039 - 0.066
(0.0015 - 0.0026)
Blue