2001 LAND ROVER FREELANDER torque

MAINTENANCE
10-6 MAINTENANCE
Alarm Handset Battery
Replace
1.Insert the blade of a small, flat bladed
screwdriver into the slot at the keyring end of
the handset and carefully prise the two halves
of the handset apart.
2.Slide the battery out of the clip taking care not
to touch the circuit board or the battery
contacts.
3.Press and hold each button in turn for at least 5
seconds to drain any residual power from the
handset.
4.Fit the replacement battery (Land Rover
STC4080 or Panasonic CR2032) ensuring the
correct polarity is maintained (+) side facing
upwards. Avoid touching the flat surfaces of the
battery.
5.Press the 2 halves of the handset together,
making sure the two halves click into place
correctly.
6.Check the operation of the handset.
Road Wheels
Remove
1.Loosen wheel nuts. Raise vehicle for wheel
free condition and remove the wheel nuts.
2.Mark the wheel to stud relationship to ensure
that the wheels are refitted in the same
orientation.
Refit
1.Apply a thin coat of anti-seize compound to
wheel hub centre.
2.Refit wheels to original hub position.
NOTE: When refitting road wheel nuts, do not
overtighten using powered tools. Ensure the
wheel nuts are correctly torqued in the correct
sequence.
3.Tighten wheel nuts to 115 Nm (85 lbf.ft).

MAINTENANCE
MAINTENANCE 10-27
Suspension
Check Front Suspension
1.Check condition of all ball joint dust covers,
including anti-roll bar links.
2.Check tightness of all accessible suspension
fixings including tie rods.
3.Check wheel bearings and suspension struts
for signs of excessive play or wear.
4.Check track rod ends for wear by attempting to
move the joint forwards and backwards, side to
side and up and down. No wear should be
apparent, if any is detected then the joint must
be replaced.
5.Check for signs of leakage from suspension
dampers.Check Rear Suspension
1.Check tightness of all accessible suspension
fixings including transverse links.
2.Check wheel bearings and suspension struts
for signs of excessive play or wear.
3.Check for signs of leakage from suspension
dampers.
Check Tow Bar Fixings
1.Check that the two vertical fixings are tightened
to a torque of 110 Nm (82 lbf.ft).
2.Check that the six transverse fixings are
tightened to a torque of 60 Nm (45 lbf.ft).

ENGINE - K SERIES KV6
12-3-12 REPAIRS
Crankshaft rear oil seal
$% 12.21.20
Remove
1.Remove torque converter drive plate.

+ ENGINE - K SERIES KV6, REPAIRS,
Torque converter drive plate.
2.Remove and discard 5 bolts securing
crankshaft rear oil seal to cylinder block.
3.Remove and discard crankshaft rear oil seal.Refit
1.Clean cylinder block face and oil seal running
surface on crankshaft; ensure bolt holes are
clean and dry.
2.Position oil seal protector, LRT-12-061 to
crankshaft.
3.Position oil seal to crankshaft.
CAUTION: Oil seal must be fitted dry.
4.Fit new Patchlok bolts securing oil seal to
cylinder block and using sequence shown,
tighten to 8 Nm (6 lbf.ft).
5.Remove oil seal protector.
6.Fit torque converter drive plate.

+ ENGINE - K SERIES KV6, REPAIRS,
Torque converter drive plate.
7.Check engine oil level, top-up if necessary.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.

ENGINE - K SERIES KV6
REPAIRS 12-3-15
Refit
1.Clean cylinder head mating face.
CAUTION: Use suitable gasket removal
spray and a plastic scraper.
2.Remove bolts securing cylinder liner clamps
LRT-12-144 to cylinder block and remove
clamps.
CAUTION: Do not rotate crankshaft.
3.Clean cylinder block face and dowel holes.
4.Clean cylinder head bolts and wipe dry.
5.Lightly lubricate threads and beneath heads of
cylinder head bolts with clean engine oil.
6.Check that fitted height of dowels is between 10
to 11 mm (0.40 to 0.43 in) above cylinder block
top face. Replace dowels if fitted height is
incorrect.
7.Fit new cylinder head gasket onto cylinder
block with the word 'TOP' uppermost.
8.With assistance, fit cylinder head and carefully
position LH inlet to RH inlet manifold.
9.Carefully enter cylinder head bolts, DO NOT
DROP. Screw bolts into place by hand.10.Tighten cylinder head bolts progressively in the
sequence shown to :
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
12.Remove and discard 'O' rings from injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail and secure injector harness to
protection cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Position CMP sensor bracket, fit and tighten
bolt to 9 Nm (7 lbf.ft).
19.Connect CMP sensor multiplug and secure to
bracket.
20.Connect breather hose to LH inlet manifold.
21.Connect coolant bleed hose to inlet manifold
and secure with clip.
22.Position ignition coils to LH inlet manifold.
23.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
24.Position ht lead guide bracket, fit and tighten
special bolt.
25.Connect ht leads to spark plugs and secure ht
leads in guide clips.
26.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.

ENGINE - K SERIES KV6
REPAIRS 12-3-19
10.Tighten cylinder head bolts progressively in the
sequence illustrated to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit RH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
12.Remove and discard lower 'O' rings from
injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail; secure injector harness to protection
cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19.Connect breather hoses to RH camshaft cover
and inlet manifold.
20.Position ignition coils to LH inlet manifold.
21.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
22.Connect multiplugs to plug top coils and secure
with locking clips.
23.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
24.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).25.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
26.Fit RH exhaust manifold gasket.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket - exhaust
manifold - RH - Non NAS.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Gasket(s) -
exhaust manifold - RH - KV6 - NAS.
27.Fit inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Seals - inlet
manifold chamber - up to 03MY.
28.Fill cooling system.

+ COOLING SYSTEM - K SERIES KV6,
ADJUSTMENTS, Coolant - drain and refill.
29.Check engine oil level and top-up if necessary.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.

ENGINE - K SERIES KV6
REPAIRS 12-3-49
Torque converter drive plate
$% 12.53.13
Remove
1.Remove automatic gearbox.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Gearbox - KV6.
2.Assemble LRT-12-161 to LRT-12-199 and
secure with clamp bolt.
3.Position LRT-12-161 and LRT-12-199 to
crankshaft pulley to restrain crankshaft.
4.Remove and discard 6 Patchlok bolts securing
drive plate to crankshaft.
5.Remove drive plate from crankshaft.Refit
1.Clean bolt holes in crankshaft using an old
drive plate bolt with two saw cuts at an angle of
45° to the bolt shank.
2.Clean drive plate and mating face of
crankshaft.
3.Position LRT-12-161 and LRT-12-199 to
crankshaft pulley to restrain crankshaft.
4.Position drive plate to crankshaft.
5.Fit new Patchlok bolts securing drive plate to
crankshaft and tighten in sequence shown to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - 100 Nm (74 lbf.ft)
6.Remove LRT-12-161 and LRT-12-199 from
crankshaft pulley.
7.Fit automatic gearbox.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Gearbox - KV6.

ENGINE - K SERIES KV6
REPAIRS 12-3-63
38.Remove and discard 2 Patchlok bolts securing
tensioner to cylinder block and remove
tensioner.
CAUTION: Exercise great care when
removing bolts, do not apply excessive
torque. If bolts appear to be seized, apply
suitable anti-seize lubricant prior to
removing bolts. DO NOT loosen Allen screw
securing tensioner pulley.
39.If camshaft timing belt is to be refitted, mark
direction of rotation on timing belt before
removal.
40.With care, ease camshaft timing belt from
gears using fingers only and remove timing
belt.
CAUTION: Do not rotate crankshaft or
camshafts with timing belt removed and
cylinder heads fitted.
CAUTION: Camshaft timing belt must be
replaced if cylinder head is to be removed or
new drive gears, tensioner or coolant pump
are to be fitted. Camshaft timing belts must
be stored and handled with care. Always
store a camshaft timing belt on its edge with
a bend radius greater than 50 mm (2.0 in).
Do not use a camshaft timing belt that has
been twisted or bent double as this will
damage the reinforcing fibres. Do not use a
camshaft timing belt if debris other than belt
dust is found in timing belt covers. Do not
use a camshaft timing belt if partial engine
seizure has occurred. Do not use a
camshaft timing belt if mileage exceeds
72,000 km (45,000 miles). Do not use an oil
or coolant contaminated timing belt, cause
of contamination must be rectified.41.Remove and discard LH and RH exhaust
camshaft cap seals.
42.Position tools LRT-12-196 to LH and RH front
inlet camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
43.Remove and discard bolts retaining front inlet
camshaft gears to camshafts.
44.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.
45.Remove camshaft drive gears and hub
assemblies.

ENGINE - K SERIES KV6
12-3-90 OVERHAUL
10.Tighten cylinder head bolts progressively in the
sequence shown to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - 25 Nm (18 lbf.ft)
lStage 3 - 25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten a bolts in same sequence a further
180°
11.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
12.Remove and discard 'O' rings from injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail and secure injector harness to
protection cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19.Connect breather hose to LH inlet manifold.
20.Position ignition coils to LH inlet manifold.
21.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
22.Clean camshaft drive belt cover backplate bolts
and apply sealant, Part No. STC 50552 to first
3 threads.
23.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).
24.Clean exhaust manifold and cylinder head
mating face.25.Fit new exhaust manifold gasket. Position
exhaust manifold, fit nuts and using sequence
shown, tighten to 45 Nm (33 lbf.ft).
26.Secure HO2S lead in clip on cylinder block.
27.Connect HO2S multiplug and secure to support
bracket.
28.Fit new camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.