2001 LAND ROVER FREELANDER oil

TORQUE WRENCH SETTINGS
06-11
Engine Management System – Siemens
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor 8 Nm 6 lbf.ft
CMP sensor mounting bracket bolt 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor bolt 9 Nm 6.5 lbf.ft
Engine Coolant temperature (ECT) sensor 17 Nm 12.5 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Plug top coils to LH inlet manifold nut and bolt 9 Nm 6.5 lbf.ft
Plug top coils to RH camshaft cover bolts 9 Nm 6.5 lbf.ft
Spark plugs25 Nm 18 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle pedal assembly to bulkhead nuts 25 Nm 18 lbf.ft
Throttle position (TP) sensor screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-12
Fuel Delivery System – Diesel
TORQUE DESCRIPTION METRIC IMPERIAL
Air cleaner cover Allen screws 8 Nm 6 lbf.ft
Condenser to radiator bolts 3 Nm 2.2 lbf.ft
Filler neck to body nuts and bolt 9 Nm 6.5 lbf.ft
Fuel cooler to mounting bracket bolts 10 Nm 7 lbf.ft
Fuel cooler matrix to bonnet locking platform nuts 10 Nm 7 lbf.ft
Fuel cut-off (inertia) switch to bracket nuts 2 Nm 1.5 lbf.ft
Fuel injector clamp nuts 10 Nm 7 lbf.ft
Fuel injector pipe union nuts 20 Nm 15 lbf.ft
Fuel injection pump nuts 24 Nm 18 lbf.ft
Fuel injection pump sprocket nut 65 Nm 48 lbf.ft
Fuel injector studs 10 Nm 7 lbf.ft
Fuel pressure regulator Torx screws 9 Nm 6.5 lbf.ft
Fuel pressure sensor 38 Nm 28 lbf.ft
Fuel pump/sender unit to tank locking ring 35 Nm 26 lbf.ft
Fuel rails to support bracket bolt 10 Nm 7.5 lbf.ft
Fuel rail Allen screws 24 Nm 18 lbf.ft
Fuel tank to body bolts 45 Nm 33 lbf.ft
Glow plugs20 Nm 15 lbf.ft
High pressure fuel pipe union nuts 20 Nm 15 lbf.ft
Intercooler to radiator bolts 3 Nm 2.2 lbf.ft
Low pressure fuel rail bolts 10 Nm 7 lbf.ft
Timing case access plug 30 Nm 22 lbf.ft
Turbocharger boost control solenoid valve mounting bracket to turbocharger bolts 10 Nm 7 lbf.ft
Turbocharger boost control solenoid valve to mounting rubber nuts 5 Nm 3.7 lbf.ft
Turbocharger boost pressure sensor to inlet manifold bolt 8 Nm 6 lbf.ft
Turbocharger oil drain pipe bracket bolts 20 Nm 15 lbf.ft
Turbocharger oil drain pipe flange bolts 8 Nm 6 lbf.ft
Turbocharger oil feed pipe banjo bolts 22 Nm 16 lbf.ft
Turbocharger outlet pipe to bracket bolts:
⇒ 6 mm10 Nm 7 lbf.ft
⇒ 8 mm20 Nm 15 lbf.ft
Turbocharger to exhaust manifold bolts 50 Nm 37 lbf.ft

TORQUE WRENCH SETTINGS
06-13
Fuel delivery system – Petrol
1 Tighten in sequence using the procedure defined in 'Repairs' section.

+ ENGINE MANAGEMENT SYSTEM - SIEMENS, REPAIRS, Sensor - combined - manifold absolute
pressure/Intake air temperature (MAP/IAT).
TORQUE DESCRIPTION METRIC IMPERIAL
Air cleaner to battery tray bolts 9 Nm 7 lbf.ft
Fuel filler neck to body nuts and bolt 9 Nm 7 lbf.ft
Fuel pump/sender unit to tank locking ring 35 Nm 26 lbf.ft
Fuel rail to inlet manifold bolt 8 Nm 6 lbf.ft
Fuel tank to body bolts 40 Nm 29 lbf.ft
Heated Oxygen (HO
2S) Sensor 40 Nm 29 lbf.ft
Ignition coils to LH inlet manifold nuts and bolts - KV6 - Up to 03 Model Year 9 Nm 7 lbf.ft
Inertia (fuel cut-off) switch 2 Nm 1.5 lbf.ft
Intake Air Control Valve (IACV) to throttle body Allen screws 6 Nm 4.5 lbf.ft
Subframe to body bolts 190 Nm 140 lbf.ft
Throttle housing to inlet manifold bolts
1 (K1.8)
⇒1st. stage4 Nm 3 lbf.ft
⇒2nd. stage9 Nm 7 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 8 Nm 6 lbf.ft
Throttle actuator support bracket to throttle body Torx screws (vehicles with cruise
control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft
VIS motor to inlet manifold chamber screws (KV6 only) 8 Nm 6 lbf.ft

TORQUE WRENCH SETTINGS
06-16
Manifolds and Exhaust Systems – K1.8
†Tighten in sequence.
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator bolts45 Nm 33 lbf.ft
Alternator mounting bracket bolts 25 Nm 18 lbf.ft
Coil cover bolts10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold bolts 10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold nut 25 Nm 18 lbf.ft
Exhaust front pipe to intermediate pipe nuts 60 Nm 44 lbf.ft
Exhaust front pipe to manifold nuts 60 Nm 44 lbf.ft
Exhaust manifold to cylinder head nuts
†45 Nm 33 lbf.ft
Exhaust manifold heatshield to front pipe bolts 9 Nm 7 lbf.ft
Heated Oxygen (HO
2S) Sensor 55 Nm 41 lbf.ft
Heatshield to alternator bracket:
⇒ Nut25 Nm 18 lbf.ft
⇒ Bolts10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts
†17 Nm 12.5 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
RH coil bolts10 Nm 7.5 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-24
Rear Axles and Final Drive
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Rear differential pinion nut:
⇒ Initial tightening190 Nm 140 lbf.ft
⇒ Maximum373 Nm 275 lbf.ft
Rear cover to differential casing bolts
+25 Nm 18 lbf.ft
Rear differential to front mounting bolts 65 Nm 48 lbf.ft
Rear differential front mounting bush to subframe bolt 120 Nm 89 lbf.ft
Rear differential to rear mounting bolts 65 Nm 48 lbf.ft
Rear differential oil plug 27 Nm 20 lbf.ft
Trailing link to rear hub nut and bolt 120 Nm 89 lbf.ft

TORQUE WRENCH SETTINGS
06-28
Brakes
1 Use NEW bolts
TORQUE DESCRIPTION METRIC IMPERIAL
ABS ECU pipe unions 17 Nm 12 lbf.ft
ABS modulator to mounting bracket bolts 9 Nm 7 lbf.ft
ABS modulator mounting bracket to inner wing:
⇒ Nuts
⇒ Bolts13 Nm
8 Nm10 lbf.ft
6 lbf.ft
Bleed screw - front calipers 10 Nm 7.5 lbf.ft
Brake servo to bulkhead nuts 22 Nm 16 lbf.ft
EGR cooler to mounting bolts 25 Nm 18 lbf.ft
EGR pipe support bracket to engine lifting bracket bolts 25 Nm 18 lbf.ft
Front caliper brake hose banjo bolt 28 Nm 21 lbf.ft
Front caliper guide pin bolts 27 Nm 20 lbf.ft
Front caliper mounting bolts 100 Nm 74 lbf.ft
Front disc shield to hub screw 8.5 Nm 6.3 lbf.ft
Front disc to drive flange screws 5 Nm 3.7 lbf.ft
Fuel rail to support bracket bolt 10 Nm 7.5 lbf.ft
Handbrake cable to body and subframe bolts 22 Nm 16 lbf.ft
Handbrake cable retaining plate bolts 22 Nm 16 lbf.ft
Handbrake lever assembly to body bolts 22 Nm 16 lbf.ft
Hill Descent Control (HDC) switch bolt 5 Nm 3.5 lbf.ft
Master cylinder to servo nuts 25 Nm 18 lbf.ft
PAS oil cooler pipe bolts 10 Nm 7.5 lbf.ft
Primary and secondary brake pipe union nuts 17 Nm 12 lbf.ft
Rear wheel cylinder pipe union nut 17 Nm 12 lbf.ft
Rear wheel cylinder to backplate bolts 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 8 Nm 6 lbf.ft
Reservoir to master cylinder (LHD) Torx bolt 6 Nm 4.5 lbf.ft
Road wheel nuts 115 Nm 85 lbf.ft
Turbocharger intercooler pipe to support bracket bolt 10 Nm 7.5 lbf.ft
Turbocharger pipe to coolant rail bolt 25 Nm 18 lbf.ft
Vacuum pump bolts
122 Nm 16 lbf.ft
Vacuum reservoir to mounting bracket nut 10 Nm 7.5 lbf.ft

LIFTING AND TOWING
08-3
If the front of the vehicle is to be trailed, turn ignition
key to position 'I' to release steering lock.
WARNING: Do not turn the starter switch to
position '0' or remove the ignition key while the
vehicle is being towed.
CAUTION: If it is considered unsafe to turn the
starter switch to position '1' due to accident
damage or an electrical fault; disconnect the
battery before turning the ignition switch.
CAUTION: The steering wheel and/or linkage
must be secured in a straight ahead position. DO
NOT use the steering lock mechanism for this
purpose.
CAUTION: Under no circumstances should the
vehicle be towed or recovered by means of
lashing to the rear subframe. Serious damage to
the subframe and body could result.
CAUTION: Only use the rear towing eye for
towing another vehicle.
Towing eyes
The towing eyes at the front and rear of the vehicle
are designed for vehicle recovery purposes only and
must not be used to tow a trailer or caravan.
Front and rear towing eyes
A single towing eye is provided in the front spoiler.
Only use when the vehicle is to be towed with all four
wheels on the ground.
A single towing eye is provided in the rear RH spoiler.
Only use when towing another vehicle.Transporting the vehicle by trailer
Lashing rings are provided at the front and rear of the
body to facilitate the securing of the vehicle to a
trailer or other means of transportation.
CAUTION: Underbody components must not be
used as lashing points. The lashing rings must
not be used for towing.
Install the vehicle on trailer and apply the parking
brake. Select neutral.
Lashing eyes
Lashing rings are provided at the front and rear of the
vehicle for use when transporting by trailer. DO NOT
use lashing eyes for towing purposes.
Front lashing eye
Rear lashing eyes

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-1
CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
Capacities
The following capacities are only an approximation of
the amount of fluid required to fill the respective
system.
Capacities – UK/ROW
† An extra 420 cc (0.73 imp pt) is required for
vehicles with an air blast fluid cooler fitted.
* Refill capacity is approx. 0.7 litre (1.125 imp. pt)
less than the from dry figures.
Capacities – NAS
Component / system Capacity
Fuel tank:
Td4 Model
K1.8 and KV6 Models
⇒ Up to 03 Model Year
⇒ From 03 Model Year
KV6 Model
⇒ Up to 03 Model Year
⇒ From 03 Model Year59 litres (13 gallons)
59 litres (13 gallons)
64 litres (14.3 gallons)
59 litres (13 gallons)
64 litres (14.3 gallons)
Engine - Td4 (including oil cooler and oil filter):
⇒ Refill 6.8 litres (12 imp. pts)
⇒ Fill from dry 7.3 litres (12.9 imp. pts)
Engine - K1.8 (including filter):
⇒ Refill 4.5 litres (7.9 imp. pts)
⇒ Fill from dry 4.8 litres (8.4 imp. pts)
Engine - KV6 (including oil cooler and filter):
⇒ Refill 5.2 litres (9.125 imp. pts)
⇒ Fill from dry 6.0 litres (10.625 imp. pts)
Manual gearbox - PG1:
⇒ Refill 2.0 litres (3.5 imp. pts)
⇒ From dry 2.2 litres (3.9 imp. pts)
Manual gearbox - Getrag:
⇒ Refill 1.6 litres (2.875 imp. pts)
⇒ From dry 1.67 litres (3 imp. pts)
Automatic gearbox - JATCO:
⇒ Refill 4.0 litres (7 imp. pts)
⇒ From dry
†8.5 litres (15 imp. pts)
Intermediate Reduction
Drive1.1 litres (2 imp. pts)
Rear differential:
⇒ Maximum 830 ml (29.2 imp. fl. oz.)
⇒ Minimum 750 ml (26.4 imp. fl. oz.)
Power steering reservoir 335 cm
3
Cooling system - Td4 Engine – Fill from dry (with
reservoir)*:
⇒ Automatic - Up to 03
Model Year
⇒ Automatic - From 03
Model Year7.25 litres (12.8 imp. pts)
7.35 litres (13 imp. pts)
⇒ Manual 7.25 litres (12.8 imp. pts)
Cooling system - K1.8 Engine:
⇒ Fill from dry (with
reservoir)*5.8 litres (10.25 imp. pts)
Cooling system - KV6 Engine:
⇒ Fill from dry (with
reservoir)*7.8 litres (13.75 imp. pts)
Reservoir tank:
⇒ Maximum fill 0.44 litres (0.75 imp. pts)
⇒ Expansion tank volume 1.2 litres (2.125 imp. pts)
⇒ Gross expansion
capacity0.72 litres (1.27 imp. pts)
Windscreen washer
reservoir 4.0 litres (7 imp. pints)
Component / system Capacity
Fuel tank:
⇒ Up to 02.5 Model Year
⇒ From 02.5 Model Year15.6 US gallons
17.2 US gallons
Engine - KV6 (including oil cooler and filter):
⇒ Engine oil and filter
change11 US pts
⇒ Fill from dry 12.7 US pts
Automatic gearbox - JATCO:
⇒ Refill 8.5 US pts
⇒ From dry 18.2 US pts
Intermediate Reduction
Drive2.3 US pts
Rear differential:
⇒ Maximum
⇒ Minimum28.1 US fl. oz.
25.4 US fl. oz.
Power steering reservoir 335 cm
3
Cooling system - KV6 Engine:
⇒ Fill from dry (with
reservoir)17.82 US pts
Reservoir tank:
⇒ Maximum fill 0.93 US pts
⇒ Expansion tank volume 2.54 US pts
⇒ Gross expansion
capacity1.52 US pts
Windscreen washer
reservoir 8.5 US pts Component / system Capacity