2001 LAND ROVER FREELANDER sensor

TORQUE WRENCH SETTINGS
06-13
Fuel delivery system – Petrol
1 Tighten in sequence using the procedure defined in 'Repairs' section.

+ ENGINE MANAGEMENT SYSTEM - SIEMENS, REPAIRS, Sensor - combined - manifold absolute
pressure/Intake air temperature (MAP/IAT).
TORQUE DESCRIPTION METRIC IMPERIAL
Air cleaner to battery tray bolts 9 Nm 7 lbf.ft
Fuel filler neck to body nuts and bolt 9 Nm 7 lbf.ft
Fuel pump/sender unit to tank locking ring 35 Nm 26 lbf.ft
Fuel rail to inlet manifold bolt 8 Nm 6 lbf.ft
Fuel tank to body bolts 40 Nm 29 lbf.ft
Heated Oxygen (HO
2S) Sensor 40 Nm 29 lbf.ft
Ignition coils to LH inlet manifold nuts and bolts - KV6 - Up to 03 Model Year 9 Nm 7 lbf.ft
Inertia (fuel cut-off) switch 2 Nm 1.5 lbf.ft
Intake Air Control Valve (IACV) to throttle body Allen screws 6 Nm 4.5 lbf.ft
Subframe to body bolts 190 Nm 140 lbf.ft
Throttle housing to inlet manifold bolts
1 (K1.8)
⇒1st. stage4 Nm 3 lbf.ft
⇒2nd. stage9 Nm 7 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 8 Nm 6 lbf.ft
Throttle actuator support bracket to throttle body Torx screws (vehicles with cruise
control only)9 Nm 7 lbf.ft
Throttle position sensor to housing Torx screws 1.5 Nm 1.1 lbf.ft
VIS motor to inlet manifold chamber screws (KV6 only) 8 Nm 6 lbf.ft

TORQUE WRENCH SETTINGS
06-16
Manifolds and Exhaust Systems – K1.8
†Tighten in sequence.
TORQUE DESCRIPTION METRIC IMPERIAL
Alternator bolts45 Nm 33 lbf.ft
Alternator mounting bracket bolts 25 Nm 18 lbf.ft
Coil cover bolts10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold bolts 10 Nm 7.5 lbf.ft
Exhaust heatshield to manifold nut 25 Nm 18 lbf.ft
Exhaust front pipe to intermediate pipe nuts 60 Nm 44 lbf.ft
Exhaust front pipe to manifold nuts 60 Nm 44 lbf.ft
Exhaust manifold to cylinder head nuts
†45 Nm 33 lbf.ft
Exhaust manifold heatshield to front pipe bolts 9 Nm 7 lbf.ft
Heated Oxygen (HO
2S) Sensor 55 Nm 41 lbf.ft
Heatshield to alternator bracket:
⇒ Nut25 Nm 18 lbf.ft
⇒ Bolts10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts
†17 Nm 12.5 lbf.ft
Intermediate pipe to tail pipe flange nuts 60 Nm 44 lbf.ft
RH coil bolts10 Nm 7.5 lbf.ft
Tail pipe clamp nut 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-17
Manifolds and Exhaust Systems – KV6
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant/breather hose bracket to inlet manifold bolt 9 Nm 6.5 lbf.ft
Exhaust heatshield to exhaust mounting bracket bolts 45 Nm 33 lbf.ft
Exhaust heatshield to IRD housing nut 45 Nm 33 lbf.ft
Exhaust heatshield to lower engine steady mounting bracket bolts 9 Nm 6.5 lbf.ft
Exhaust heatshield to pinion housing nuts 25 Nm 18 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust manifold to cylinder head nuts 45 Nm 33 lbf.ft
Exhaust front pipe to manifold flange nuts 50 Nm 37 lbf.ft
Heated Oxygen (HO
2S) sensor 55 Nm 41 lbf.ft
Inlet manifold chamber to inlet manifold bolts 18 Nm 13 lbf.ft
Inlet manifold chamber support brackets to RH camshaft cover bolts 10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts and bolts 25 Nm 18 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 37 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 44 lbf.ft
Lower engine steady to subframe bolt 100 Nm 74 lbf.ft
Lower engine steady to sump mounting bolt 100 Nm 74 lbf.ft
RH upper engine steady to body bolt 100 Nm 74 lbf.ft
RH upper engine steady to top arm bolt 100 Nm 74 lbf.ft
Tail pipe clamp nuts 55 Nm 41 lbf.ft

TORQUE WRENCH SETTINGS
06-22
Automatic Gearbox – Jatco
†Tighten in sequence.
+ Apply sealant, Part No. STC 4600 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
Air blast cooler assembly to chassis bolts:
⇒ Lower10 Nm 7.5 lbf.ft
⇒ Upper5 Nm 3.5 lbf.ft
Air blast cooler fan cowl to matrix bolts 5 Nm 3.5 lbf.ft
Air blast cooler fan motor to cowl bolts 5 Nm 3.5 lbf.ft
Air blast cooler multiplug mounting bracket nut 10 Nm 7.5 lbf.ft
Air blast cooler pipe union nuts 25 Nm 18 lbf.ft
Crankshaft Position (CKP) Sensor 9 Nm 7 lbf.ft
Closing panel to gearbox panel bolt 10 Nm 7.5 lbf.ft
Drive plate to converter bolts 45 Nm 33 lbf.ft
Earth lead to gearbox housing bolt 25 Nm 18 lbf.ft
Fluid cooler to mounting bracket bolts (KV6) 25 Nm 18 lbf.ft
Fluid cooler mounting bracket bolts (KV6):
⇒ M825 Nm 18 lbf.ft
⇒ M1285 Nm 63 lbf.ft
Fluid cooler mounting bolts (Td4):
⇒ 2 off45 Nm 33 lbf.ft
⇒ 1 off25 Nm 18 lbf.ft
Fluid cooler hoses to gearbox 18 Nm 13 lbf.ft
Fluid cooler hose unions 18 Nm 13 lbf.ft
Fluid pan bolts
† +7 Nm 5 lbf.ft
Gearbox closing plate bolt (Td4) 10 Nm 7.5 lbf.ft
Gearbox drain plug 45 Nm 33 lbf.ft
Gearbox level plug 14 Nm 10 lbf.ft
Gearbox housing to sump 85 Nm 63 lbf.ft
Gearbox to engine bolts 85 Nm 63 lbf.ft
Gearbox mounting bracket bolts 85 Nm 63 lbf.ft
Gearbox mounting through bolt 100 Nm 74 lbf.ft
Inhibitor switch bolts 3 Nm 2.2 lbf.ft
IRD cooling hose retainer bolt (KV6) 25 Nm 18 lbf.ft
IRD support bracket mounting bolts
† (KV6) 50 Nm 37 lbf.ft
IRD support bracket to engine front mounting bracket bolts
† (KV6) 50 Nm 37 lbf.ft
IRD support bracket to sump bolts
† (KV6) 45 Nm 33 lbf.ft
IRD to gearbox bolts (KV6) 80 Nm 59 lbf.ft
Manifold heatshield to IRD support bracket (KV6):
⇒ Bolts9 Nm 7 lbf.ft
⇒ Nut45 Nm 33 lbf.ft
Manifold heatshield to IRD pinion housing nut (KV6) 25 Nm 18 lbf.ft
Selector housing nuts 10 Nm 7.5 lbf.ft
Selector cable trunnion nut 6 Nm 4.5 lbf.ft
Selector lever to gearbox selector shaft nut 25 Nm 18 lbf.ft
Starter motor to gearbox bolts 45 Nm 33 lbf.ft
Torque converter access plate bolts 9 Nm 7 lbf.ft

TORQUE WRENCH SETTINGS
06-33
Air Conditioning
TORQUE DESCRIPTION METRIC IMPERIAL
A/C compressor to mounting bracket bolts (Td4 & K1.8) 25 Nm 18 lbf.ft
A/C compressor mounting bracket to cylinder block bolts (Td4 & K1.8) 45 Nm 33 lbf.ft
A/C compressor mounting bracket to cylinder block bolts (KV6) 45 Nm 33 lbf.ft
A/C compressor support bracket to sump bolt (Td4) 10 Nm 7.5 lbf.ft
A/C compressor drive belt tensioner clamp bolt (Td4) 24 Nm 18 lbf.ft
A/C compressor drive belt tensioner pivot bolt (Td4) 24 Nm 18 lbf.ft
A/C compressor upper and lower securing bolts (KV6) 25 Nm 18 lbf.ft
A/C pipe rail to condenser bolt (KV6) 8 Nm 6 lbf.ft
A/C pipe rail to condenser bolt (KV6) 8 Nm 6 lbf.ft
Condenser bracket to radiator bolts 8 Nm 6 lbf.ft
Receiver drier to condenser bolts 12 Nm 9 lbf.ft
Refrigerant pressure sensor 10 Nm 7.5 lbf.ft
TXV to bulkhead Allen screws 25 Nm 18 lbf.ft

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-4
Sealants
The following table lists those sealants which are
used during repair / overhaul procedures covered in
this manual; it is essential that the sealant specified
for a particular procedure is used at all times.
Component Application Land Rover
Part No.
Td4 Engine Camshaft cover
gasket joint linesSTC 50550
Td4 Engine Sump gasket joint
linesSTC 50550
K 1.8 Engine Oil pressure switch
threadsSTC 50552
K 1.8 Engine Oil pressure relief
valve plug threadsSTC 50552
K 1.8 Engine Oil temperature
sensor threadsSTC 50552
K 1.8 Engine Oil pump cover
plate screwsSTC 50552
K 1.8 Engine Camshaft carrier to
cylinder headSTC 4600
K 1.8 Engine Bearing ladder to
cylinder blockSTC 4600
K 1.8 Engine Sump to bearing
ladderSTC 4600
K 1.8 Engine Oil rail to bearing
ladderSTC 4600
K 1.8 Engine Crankshaft rear oil
seal STC 50550
K 1.8 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Camshaft timing
belt backplate
cover boltsSTC 50552
KV6 Engine Oil pressure relief
valve plug threadsSTC 50552
KV6 Engine Oil pump cover
plate screwsSTC 50552
KV6 Engine Camshaft carrier to
cylinder headSTC 4600
KV6 Engine Sump to lower
crankcaseSTC 4600
KV6 Engine Oil pick-up strainer
boltSTC 50552
KV6 Engine Lower crankcase to
cylinder blockSTC 50550
KV6 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Coolant stub pipe to
cylinder blockSTC 50554
Engine
Management
System -
MEMSSensor - Engine
Coolant
temperature (ECT)STC 50552
Cooling
System - KV6Cylinder block drain
plugSTC 50552
Manual
Gearbox - PG12 top bolts -
gearbox to engineSTC 50552
Manual
Gearbox -
GetragRear cover to
gearcaseSTC 4600
Manual
Gearbox -
GetragGearshift cover STC 4600
Intermediate
Reduction
DriveEnd cover gasket -
IRD housingSTC 4600
Automatic
Gearbox -
JatcoFluid pan to
gearcaseSTC 4600
Rear Axle and
Final DriveDifferential cover to
casingSTC 3811

MAINTENANCE
MAINTENANCE 10-9
Brake Fluid
Replace
1.Replace brake fluid.

+ BRAKES, ADJUSTMENTS, Brake
bleed.
Road Wheel Speed Sensors
Inspect
Front wheel
1.Check harness is correctly routed and secured.
Ensure harness shows no sign of damage or
chafing.
2.Check speed sensor is fully inserted to the
correct position. Check reluctor ring condition
and ensure it is free from debris.
Rear wheel
3.Check harness is correctly routed and secured.
Ensure harness shows no sign of damage or
chafing.
4.Check speed sensor is fully inserted to the
correct position. Check reluctor ring condition
and ensure it is free from debris.

ENGINE - K SERIES KV6
REPAIRS 12-3-15
Refit
1.Clean cylinder head mating face.
CAUTION: Use suitable gasket removal
spray and a plastic scraper.
2.Remove bolts securing cylinder liner clamps
LRT-12-144 to cylinder block and remove
clamps.
CAUTION: Do not rotate crankshaft.
3.Clean cylinder block face and dowel holes.
4.Clean cylinder head bolts and wipe dry.
5.Lightly lubricate threads and beneath heads of
cylinder head bolts with clean engine oil.
6.Check that fitted height of dowels is between 10
to 11 mm (0.40 to 0.43 in) above cylinder block
top face. Replace dowels if fitted height is
incorrect.
7.Fit new cylinder head gasket onto cylinder
block with the word 'TOP' uppermost.
8.With assistance, fit cylinder head and carefully
position LH inlet to RH inlet manifold.
9.Carefully enter cylinder head bolts, DO NOT
DROP. Screw bolts into place by hand.10.Tighten cylinder head bolts progressively in the
sequence shown to :
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 3 -Tighten in the same sequence to
25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten bolts in the same sequence a further
180°
11.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
12.Remove and discard 'O' rings from injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail and secure injector harness to
protection cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Position CMP sensor bracket, fit and tighten
bolt to 9 Nm (7 lbf.ft).
19.Connect CMP sensor multiplug and secure to
bracket.
20.Connect breather hose to LH inlet manifold.
21.Connect coolant bleed hose to inlet manifold
and secure with clip.
22.Position ignition coils to LH inlet manifold.
23.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
24.Position ht lead guide bracket, fit and tighten
special bolt.
25.Connect ht leads to spark plugs and secure ht
leads in guide clips.
26.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.