2001 LAND ROVER FREELANDER seats

RESTRAINT SYSTEMS
REPAIRS 75-3
Seat belt - centre - rear
$% 76.73.20
Remove
1.Remove RH rear seat.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove 2 screws and remove seat belt reel
cover.
3.Remove nut and release seat belt reel.4.Remove 5 screws and remove both end
covers.
5.Remove 3 Torx bolts and remove squab from
cushion.
6.Release rear of cushion cover from frame.
7.Release sides and front of cushion cover from
frame.

RESTRAINT SYSTEMS
75-4 REPAIRS
8.Release cover and pad from frame.
9.Remove Torx bolt from centre seat belt anchor
and right seat belt buckle.
10.Remove seat belt and right seat belt buckle.
Refit
1.Position centre seat belt anchor and right seat
belt buckle to seat and tighten Torx bolt to 32
Nm (24 lbf.ft).
2.Fit cover and pad to frame.
3.Fit front and sides of cushion cover to frame.
4.Fit rear of cushion cover to frame.
5.Fit cushion to squab and tighten Torx bolts.
6.Fit end covers and tighten screws.
7.Position seat belt reel in seat squab and tighten
nut to 32 Nm (24 lbf.ft).
8.Fit seat belt reel cover and tighten screws.
9.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.
Seat belt - rear - LH
$% 76.73.23
Remove
1.Remove rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
2.Remove Torx bolt from seat belt upper
mounting.
3.Remove Torx bolt from seat belt reel and
remove reel.
Refit
1.Position reel and tighten Torx bolt to 50 Nm (37
lbf.ft).
2.Extend belt, position top mounting and tighten
Torx bolt to 32 Nm (24 lbf.ft).
3.Fit rear quarter upper trim casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.

RESTRAINT SYSTEMS
75-6 REPAIRS
Stalk - rear seat belt - LH - 3 door
$% 76.73.32
Remove
1.Remove rear seat.

+ SEATS, REPAIRS, Cushion & squab
- rear seat - bench type - 3 door.
2.Remove 2 screws from hinge cover and
remove cover from seat hinge.
3.Remove 4 screws and remove rear seat centre
console.
4.Release rear seat cushion cover retainers and
position cushion aside.5.Remove Torx bolt from seat belt buckle and
remove buckle.
Refit
1.Fit buckle to seat frame and tighten Torx bolt to
32 Nm (24 lbf.ft).
2.Position seat cushion and secure cover
retainers.
3.Fit centre console and secure with screws.
4.Fit hinge cover and secure with screws.
5.Fit rear seat.

+ SEATS, REPAIRS, Cushion & squab
- rear seat - bench type - 3 door.

RESTRAINT SYSTEMS
REPAIRS 75-7
Stalk - rear seat belt - LH - 5 door
$% 76.73.32
Remove
1.Fold rear seat forward.
2.Remove 3 screws from end cover and remove
cover from seat hinge.
3.Remove 4 Torx bolts from seat lock down catch
and remove catch assembly.
4.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Fit buckle to catch assembly and tighten Torx
bolt to 32 Nm (24 lbf.ft).
2.Fit catch assembly to seat and tighten Torx
bolts.
3.Fit catch assembly to seat, fit Torx bolts but do
not tighten at this stage.
4.Fold seat down and check that seat unfolds on
lock down bar correctly. Adjust catch assembly
if required.
5.Tighten catch Torx bolts to 32 Nm (24 lbf.ft).
6.Recheck seat fold.
7.Fit end cover and tighten screws.
8.Reposition rear seats.

RESTRAINT SYSTEMS
REPAIRS 75-11
Stalk - rear seat belt - centre
$% 76.73.98
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
WARNING: When removing, testing or
installing a seatbelt pre-tensioner, do not
lean directly over it or block the end of the
piston tube.
WARNING: Always remove the key from the
starter switch, disconnect the vehicle
battery and wait 10 minutes before
commencing work on the SRS system.
1.Remove RH rear seat.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove 2 screws and remove seat belt reel
cover.3.Remove nut and release seat belt reel.
4.Remove 5 screws and remove both end
covers.
5.Remove 3 Torx bolts and remove squab from
cushion.

RESTRAINT SYSTEMS
75-12 REPAIRS
6.Release rear of cushion cover from frame.
7.Release sides and front of cushion cover from
frame.
8.Release cover and pad from frame.
9.Remove Torx bolt from seat belt buckle and
remove buckle.Refit
1.Position seat belt and buckle to frame and
tighten to 32 Nm (24 lbf.ft).
2.Fit cover and pad to frame.
3.Fit front and sides of cushion cover to frame.
4.Fit rear of cushion cover to frame.
5.Fit cushion to squab and tighten Torx bolts.
6.Fit end covers and tighten screws.
7.Position seat belt reel in seat squab and tighten
nut to 32 Nm (24 lbf.ft).
8.Fit seat belt reel cover and tighten screws.
9.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

INTERIOR TRIM COMPONENTS
76-3-2 REPAIRS
Trim casing - rear quarter - lower - 5 door
$% 76.13.12
Remove
1.Release rear seat squab and fold seat forward.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release load space lamp from trim casing.
4.Disconnect 2 Lucars and remove load space
lamp.
5.Remove 2 screws securing casing to load
space carpet retainer.
6.Release 4 turn buckles securing trim casing.
7.Release trim casing from 5 retaining clips.
8.Remove loadspace side trim casing.
9.Remove 5 retaining clips from trim casing.Refit
1.Fit retaining clips to casing.
2.Position casing in loadspace, locate and secure
retaining clips.
3.Fit turn buckles.
4.Fit screws securing casing to carpet retainer.
5.Position load space lamp to casing, connect
Lucars and secure lamp to casing.
6.Position loadspace cover retainer and secure
with screw.
7.Fit loadspace cover and secure in retainers.
8.Position rear seat belt and tighten bolt to 40 Nm
(29 lbf.ft).
9.Reposition rear seats.

INTERIOR TRIM COMPONENTS
76-3-6 REPAIRS
Trim finisher - 'B/C' post - upper - renew
$% 76.13.28
Remove
1.Remove seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Release finisher from 6 retaining clips and
remove finisher.
NOTE: Do not carry out further dismantling if
component is removed for access only.4.Remove 6 retaining clips from finisher.
5.Remove seat belt slide.
Refit
1.Fit seat belt slide to finisher.
2.Fit retaining clips to finisher.
3.Position finisher and engage retaining clips.
4.Position seat belt lower mounting, fit Torx bolt
and tighten to 40 Nm (29 lbf.ft).
5.Fit seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.