2001 LAND ROVER FREELANDER seats

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-7
Trim finisher - 'B' post - lower - 5 door
$% 76.13.29
Remove
1.Remove front seat cushion side finisher.

+ SEATS, REPAIRS, Finisher -
cushion side - front seat.
2.Remove scrivet and 5 Torx screws securing
front carpet retainer and remove carpet
retainer.
3.Release 'B/C' post upper finisher.4.Remove 3 Torx screws from top of seat base
finisher.
5.Remove scrivet and Torx screw from 'B/C' post
lower finisher.
6.Release and remove 'B/C' post lower finisher
from seat base finisher.
Refit
1.Locate 'B/C' post lower finisher under seat base
finisher and rear carpet retainer.
2.Fit scrivet and Torx screw to 'B/C' post lower
finisher.
3.Fit Torx screws to seat base finisher.
4.Align and secure 'B/C' post upper finisher.
5.Fit front seat cushion side finisher.

+ SEATS, REPAIRS, Finisher -
cushion side - front seat.
6.Fit carpet retainer and secure with Torx screws
and scrivet.

INTERIOR TRIM COMPONENTS
76-3-8 REPAIRS
Trim casing - body side - rear - 3 door
$% 76.13.57
Remove
1.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove Torx bolt securing rear seat belt lower
fixing to body and position seat belt aside.
3.Remove 4 Torx bolts securing trim casing to
body.
4.Release 2 trim clips and trim casing.
5.Disconnect multiplug from tweeter if fitted.
6.Remove trim casing.
Do not carry out further dismantling if
component is removed for access only7.Noting the position of the 3 long screws,
remove 10 Torx screws and remove pocket
from trim casing.
8.Remove 3 screws securing pocket finisher to
trim casing and remove finisher.
9.Release 6 tags and remove speaker grille.
Refit
1.Position speaker grille on replacement casing
and secure tags.
2.Fit pocket finisher and secure with screws.
3.Fit pocket and secure with Torx screws.
4.Fit trim clips to trim casing.
5.Position trim casing and if fitted connect
tweeter multiplug.
6.Fit trim casing to body and secure with clips and
Torx screws.
7.Fit seat belt lower fixing and tighten Torx bolt to
50 Nm (37 lbf.ft).
8.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

SEATS
REPAIRS 76-5-1
SEATS REPAIRS
Front seat
$% 78.10.44.99
Remove
1.Make the SRS system safe.

+ GENERAL INFORMATION,
Supplementary restraint system
precautions.
2.Remove seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
3.Release pretensioner multiplug from seat
frame and disconnect.
4.Remove cover from rear securing bolt.
5.Remove 4 Torx screws securing seat.
6.Remove front seat.
Refit
1.Position front seat and secure with Torx
screws.Tighten screws to 45 Nm (33 lbf.ft).
2.Fit cover to rear bolt.
3.Connect pretensioner multiplug and secure to
seat frame.
4.Fit seat base finisher.

+ SEATS, REPAIRS, Finisher - seat
base - front - each.
Rear seat - LH
$% 78.10.48.99
Remove
1.Remove 2 Torx bolts from seat hinges.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.Remove seat.
Refit
1.Position seat in vehicle and align hinges.
2.Fit Torx bolts to seat hinges and tighten to 25
Nm (18 lbf.ft).
3.Lower seat.
4.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).

SEATS
76-5-2 REPAIRS
Rear seat - RH
$% 78.10.49.99
Remove
1.Remove 2 Torx bolts from seat hinges.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.Remove seat.
Refit
1.Position seat in vehicle and align hinges.
2.Fit Torx bolts to seat hinges and tighten to 25
Nm (18 lbf.ft).
3.Lower seat.
4.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).
Cushion & squab - rear seat - bench type
- 3 door
$% 78.10.57.99
Remove
1.Remove 2 Torx bolts securing seat to heel
board.
2.Fold seat forward and remove 2 Torx bolts from
hinges.
3.With assistance, remove seat.
Refit
1.With assistance, position seat and align hinges.
2.Fit Torx bolts, lower seat and tighten to 25 Nm
(18 lbf.ft).
3.Fit Torx bolts to heel board and tighten to 25
Nm (18 lbf.ft).

SEATS
REPAIRS 76-5-3
Cover - one piece - front seat cushion
$% 78.30.01
Remove
1.Remove front seat.

+ SEATS, REPAIRS, Front seat.
2.Remove recline control knob.
3.Release retaining studs from side covers and
remove covers.
4.Disconnect 2 multiplugs from underside of seat
cushion.
5.Release 2 clips securing multiplug to seat
frame.
6.Remove 4 Torx bolts from squab frame and
remove squab frame from cushion frame.7.Release clips securing side edges of cushion
cover to seat frame.
8.Release clip securing front edge of cushion
cover to seat frame.
9.Release main central clip securing rear edge of
cushion cover to seat frame.
10.Release rear of cushion pad from frame.
11.Remove cushion cover and pad.

SEATS
76-5-4 REPAIRS
12.Remove 12 hog rings securing cover to
cushion.
13.Remove cushion cover from cushion.
Refit
1.Position cushion cover to cushion pad and
secure to frame with hog rings in position noted
during removal.
2.Position and secure cushion cover and pad to
frame.
3.Fit squab frame to cushion frame and tighten
Torx bolts to 45 Nm (33 lbf.ft).
4.Connect multiplugs.
5.Position multiplug to frame and secure clips.
6.Fit recline control knob.
7.Fit side covers and secure retaining studs.
8.Fit front seat.

+ SEATS, REPAIRS, Front seat.
Cover - rear seat cushion - RH
$% 78.40.04
Remove
1.Remove RH rear seats.

+ SEATS, REPAIRS, Rear seat - RH.
2.Remove 2 screws and remove seat belt reel
cover.
3.Remove nut and release seat belt reel.

SEATS
REPAIRS 76-5-5
4.Remove 5 screws and remove both end
covers.
5.Remove 3 Torx bolts and remove squab from
cushion.
6.Release rear of cushion cover from frame.
7.Release sides and front of cushion cover from
frame.
8.Release cover and pad from frame.9.Remove 2 Torx bolts from seat belt and buckle
and remove seat belt and buckle from frame.
10.Remove cushion cover and pad.
11.Remove and discard 17 hog rings and remove
cover from pad.
Refit
1.Position cushion cover to cushion pad and
secure to frame with hog rings in position noted
during removal.
2.Position seat belt and buckle to frame and
tighten to 32 Nm (24 lbf.ft).
3.Fit squab cover and pad to frame.
4.Fit front and sides of cushion cover to frame.
5.Fit rear of cushion cover to frame.
6.Fit cushion to squab and tighten Torx bolts to
28 Nm (21 lbf.ft).
7.Fit end covers and tighten screws.
8.Position seat belt reel in seat squab and tighten
nut to 32 Nm (24 lbf.ft).
9.Fit seat belt reel cover and tighten screws.
10.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - RH.

SEATS
76-5-6 REPAIRS
Cover - rear seat cushion - LH
$% 78.40.05
Remove
1.Remove LH rear seat.

+ SEATS, REPAIRS, Rear seat - LH.
2.Remove 5 screws and remove both end
covers.
3.Remove 3 Torx bolts and remove squab from
cushion.4.Release rear of cushion cover from frame.
5.Release sides and front of cushion cover from
frame.
6.Remove cushion cover and pad.
7.Remove and discard 16 hog rings and remove
cover from pad.
Refit
1.Position cushion cover to cushion pad and
secure to frame with hog rings in position noted
during removal.
2.Fit cover and pad to frame.
3.Fit front and sides of cushion cover to frame.
4.Fit rear of cushion cover to frame.
5.Fit cushion to squab and tighten Torx bolts to
28 Nm (21 lbf.ft).
6.Fit end covers and tighten screws.
7.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - LH.