2001 LAND ROVER FREELANDER Camshaft

TORQUE WRENCH SETTINGS
06-11
Engine Management System – Siemens
TORQUE DESCRIPTION METRIC IMPERIAL
Camshaft position (CMP) sensor 8 Nm 6 lbf.ft
CMP sensor mounting bracket bolt 8 Nm 6 lbf.ft
Crankshaft position (CKP) sensor bolt 9 Nm 6.5 lbf.ft
Engine Coolant temperature (ECT) sensor 17 Nm 12.5 lbf.ft
'E' box cover Allen screws 2 Nm 1.5 lbf.ft
'E' box mounting nut 9 Nm 7 lbf.ft
Plug top coils to LH inlet manifold nut and bolt 9 Nm 6.5 lbf.ft
Plug top coils to RH camshaft cover bolts 9 Nm 6.5 lbf.ft
Spark plugs25 Nm 18 lbf.ft
Throttle body to inlet manifold chamber Torx screws (KV6) 7 Nm 5 lbf.ft
Throttle pedal assembly to bulkhead nuts 25 Nm 18 lbf.ft
Throttle position (TP) sensor screws 1.5 Nm 1.1 lbf.ft

TORQUE WRENCH SETTINGS
06-17
Manifolds and Exhaust Systems – KV6
TORQUE DESCRIPTION METRIC IMPERIAL
Coolant/breather hose bracket to inlet manifold bolt 9 Nm 6.5 lbf.ft
Exhaust heatshield to exhaust mounting bracket bolts 45 Nm 33 lbf.ft
Exhaust heatshield to IRD housing nut 45 Nm 33 lbf.ft
Exhaust heatshield to lower engine steady mounting bracket bolts 9 Nm 6.5 lbf.ft
Exhaust heatshield to pinion housing nuts 25 Nm 18 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust flange (LH) to front pipe nuts 50 Nm 37 lbf.ft
Exhaust manifold to cylinder head nuts 45 Nm 33 lbf.ft
Exhaust front pipe to manifold flange nuts 50 Nm 37 lbf.ft
Heated Oxygen (HO
2S) sensor 55 Nm 41 lbf.ft
Inlet manifold chamber to inlet manifold bolts 18 Nm 13 lbf.ft
Inlet manifold chamber support brackets to RH camshaft cover bolts 10 Nm 7.5 lbf.ft
Inlet manifold to cylinder head nuts and bolts 25 Nm 18 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 37 lbf.ft
Intermediate pipe to front pipe nuts 50 Nm 44 lbf.ft
Lower engine steady to subframe bolt 100 Nm 74 lbf.ft
Lower engine steady to sump mounting bolt 100 Nm 74 lbf.ft
RH upper engine steady to body bolt 100 Nm 74 lbf.ft
RH upper engine steady to top arm bolt 100 Nm 74 lbf.ft
Tail pipe clamp nuts 55 Nm 41 lbf.ft

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-4
Sealants
The following table lists those sealants which are
used during repair / overhaul procedures covered in
this manual; it is essential that the sealant specified
for a particular procedure is used at all times.
Component Application Land Rover
Part No.
Td4 Engine Camshaft cover
gasket joint linesSTC 50550
Td4 Engine Sump gasket joint
linesSTC 50550
K 1.8 Engine Oil pressure switch
threadsSTC 50552
K 1.8 Engine Oil pressure relief
valve plug threadsSTC 50552
K 1.8 Engine Oil temperature
sensor threadsSTC 50552
K 1.8 Engine Oil pump cover
plate screwsSTC 50552
K 1.8 Engine Camshaft carrier to
cylinder headSTC 4600
K 1.8 Engine Bearing ladder to
cylinder blockSTC 4600
K 1.8 Engine Sump to bearing
ladderSTC 4600
K 1.8 Engine Oil rail to bearing
ladderSTC 4600
K 1.8 Engine Crankshaft rear oil
seal STC 50550
K 1.8 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Camshaft timing
belt backplate
cover boltsSTC 50552
KV6 Engine Oil pressure relief
valve plug threadsSTC 50552
KV6 Engine Oil pump cover
plate screwsSTC 50552
KV6 Engine Camshaft carrier to
cylinder headSTC 4600
KV6 Engine Sump to lower
crankcaseSTC 4600
KV6 Engine Oil pick-up strainer
boltSTC 50552
KV6 Engine Lower crankcase to
cylinder blockSTC 50550
KV6 Engine Cylinder liners to
cylinder blockRTC 3347
KV6 Engine Coolant stub pipe to
cylinder blockSTC 50554
Engine
Management
System -
MEMSSensor - Engine
Coolant
temperature (ECT)STC 50552
Cooling
System - KV6Cylinder block drain
plugSTC 50552
Manual
Gearbox - PG12 top bolts -
gearbox to engineSTC 50552
Manual
Gearbox -
GetragRear cover to
gearcaseSTC 4600
Manual
Gearbox -
GetragGearshift cover STC 4600
Intermediate
Reduction
DriveEnd cover gasket -
IRD housingSTC 4600
Automatic
Gearbox -
JatcoFluid pan to
gearcaseSTC 4600
Rear Axle and
Final DriveDifferential cover to
casingSTC 3811

MAINTENANCE
MAINTENANCE 10-15
Ancillary Drive Belt – KV6
Check
1.Check ancillary drive belts for tension, signs of
fraying, damage and for any oil contamination.
Replace
1.Replace ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - KV6.
Camshaft Timing Belt – K1.8
Check
1.Check camshaft drive belt and renew if
necessary.

+ ENGINE - K SERIES 1.8, REPAIRS,
Camshaft timing belt.

MAINTENANCE
10-16 MAINTENANCE
Camshaft Timing Belt – KV6
Check
1.Check camshaft drive belt and renew if
necessary.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
Brake/Clutch Reservoir
Check/Top-up
RHD shown, LHD similar
1.Check fluid level in brake/clutch fluid reservoir.
2.Clean area around filter cap, remove cap.
3.Top-up if necessary to correct level on reservoir
using recommended fluid.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS, Fluids.
4.Fit filler cap.

MAINTENANCE
10-30 MAINTENANCE
Endorse Service Record
Check
1.Insert date and mileage of next service.
2.Insert current mileage.
3.Tick one of the boxes on the brake fluid
replacement indicator.
4.Tick one of the boxes on the camshaft drive belt
indicator.
5.Endorse service record with dealer stamp.
6.Sign and date the service record.
7.Sign and date the maintenance check sheet.
Report any Unusual Features
Check
1.Produce a written report detailing additional
work necessary, or items which may require
attention prior to the next service.

ENGINE - K SERIES KV6
REPAIRS 12-3-3
REPAIRS
Camshafts - LH cylinder head
$% 12.13.02
Remove
1.Disconnect battery earth lead.
2.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
3.Remove LH camshaft rear timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft rear timing belt - LH cylinder
head.
4.Remove LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
5.Remove 4 bolts and remove front camshaft
drive belt cover backplate from cylinder head.
6.Remove 2 bolts securing LH rear camshaft
drive belt cover backplate to cylinder head and
remove backplate.7.Using sequence shown, progressively loosen
22 bolts securing camshaft carrier to cylinder
head until valve spring pressure is released,
remove bolts.
8.Release camshaft carrier from dowels and
remove carrier.
9.Remove camshafts and discard oil seals.
10.Using a stick magnet, remove 12 hydraulic
tappets from cylinder head.
CAUTION: Store hydraulic tappets in their
fitted order and store upright. Maintain
absolute cleanliness when handling
hydraulic tappets. Failure to observe these
precautions can result in engine failure.
11.Clean camshafts and bearing running surfaces
in camshaft carrier and cylinder head.
12.Inspect camshafts and replace camshafts if
scored, pitted or excessively worn.
Note: Camshafts are colour coded - Inlet -
ORANGE; Exhaust - BLUE.
M12 6905
M12 6906

ENGINE - K SERIES KV6
12-3-4 REPAIRS
Refit
1.Thoroughly clean and lubricate hydraulic
tappets with clean engine oil. Fit hydraulic
tappets to original bores in cylinder head.
2.Ensure that mating faces of camshaft carrier
and cylinder head are clean and dry.
3.Lubricate camshafts and bearing journals with
clean engine oil.
4.Position camshafts in cylinder head with rear
timing gear drive slots in each camshaft facing
towards the centre as shown.
CAUTION: Ensure camshafts are in their
correct fitted locations, camshafts are
colour coded - Inlet - ORANGE; Exhaust -
BLUE.
5.Apply continuous thin beads of sealant, Part
No. STC 4600, to paths on camshaft carrier as
shown. Spread sealant to an even film using a
roller.
CAUTION: Ensure sealant does not enter oil
feed holes or grooves and that assembly is
completed within 20 minutes.6.Position camshaft carrier, fit and progressively
tighten bolts in the sequence shown to 10 Nm
(7.5 lbf.ft).
7.Noting that the front camshaft oil seals are
black in colour and the rear oil seals are red, fit
new camshaft oil seals using LRT-12-203 and
LRT-12-148A
CAUTION: Oil seals must be fitted dry. Do
not use tool LRT-12-148 for fitting seals.
8.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
9.Position camshaft timing belt rear cover
backplates to cylinder head, fit and tighten bolts
to 9 Nm (7 lbf.ft).
10.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
11.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.