2001 LAND ROVER FREELANDER steering wheel adjustment

CONTENTS
10 CONTENTS
REAR AXLE & FINAL DRIVE ................................................................... 51-1
REPAIRS
Differential assembly ..................................................................................................................... 51-1
Cover - rear - differential ................................................................................................................. 51-2
Bush - differential mounting - front ................................................................................................. 51-3
Bush - differential mounting - rear ................................................................................................. 51-4
Oil seal - pinion .............................................................................................................................. 51-5
Oil seal - differential housing ......................................................................................................... 51-6
STEERING ................................................................................................ 57-1
ADJUSTMENTS
Power assisted steering (PAS) system - bleed............................................................................... 57-1
Cable - key interlock - adjust .......................................................................................................... 57-1
Front wheel alignment - check & adjust .......................................................................................... 57-2
Alignment - rear wheel - check & adjust ......................................................................................... 57-3
Power steering - pressure test ........................................................................................................ 57-4
REPAIRS
Power steering rack ........................................................................................................................ 57-5
Gaiter - PAS rack ............................................................................................................................ 57-8
Oil cooler - Td4 & K1.8 models ....................................................................................................... 57-9
Oil cooler - KV6 models .................................................................................................................. 57-10
Drive belt - K1.8 .............................................................................................................................. 57-11
Pump - steering - KV6 .................................................................................................................... 57-12
Pump - steering - K1.8 .................................................................................................................... 57-14
Pump - steering - Td4 ..................................................................................................................... 57-15
Nacelle - column ............................................................................................................................. 57-16
Column lock & ignition/starter switch assembly .............................................................................. 57-17
Cable - key interlock ....................................................................................................................... 57-18
Column assembly - inner & outer ................................................................................................... 57-19
Ball joint - track rod ......................................................................................................................... 57-23
Track rod......................................................................................................................................... 57-24
Steering wheel ................................................................................................................................ 57-25
FRONT SUSPENSION .............................................................................. 60-1
REPAIRS
Anti roll bar...................................................................................................................................... 60-1
Ball joint link - anti roll bar .............................................................................................................. 60-2
Mounting rubbers - anti roll bar - set .............................................................................................. 60-2
Bearing - hub ................................................................................................................................. 60-3
Damper .......................................................................................................................................... 60-7
Lower arm assembly ...................................................................................................................... 60-10
Rear beam ..................................................................................................................................... 60-13
Bush - lower arm - front .................................................................................................................. 60-15
Bush - lower arm - rear ................................................................................................................... 60-16

CONTENTS
12 CONTENTS
RESTRAINT SYSTEMS ............................................................................ 75-1
REPAIRS
Automatic belt assembly - front - 3 door ......................................................................................... 75-1
Automatic belt assembly - front - 5 door ......................................................................................... 75-2
Seat belt - centre - rear ................................................................................................................... 75-3
Seat belt - rear - LH ........................................................................................................................ 75-4
Adjustable mounting - seat belt - 'B' pillar ....................................................................................... 75-5
Stalk - rear seat belt - LH - 3 door .................................................................................................. 75-6
Stalk - rear seat belt - LH - 5 door .................................................................................................. 75-7
Pre-tensioner - seat belt - front ....................................................................................................... 75-8
Pre-tensioner - seat belt - front - deployment - off vehicle ............................................................. 75-9
Stalk - rear seat belt - centre .......................................................................................................... 75-11
Air bag - steering wheel .................................................................................................................. 75-13
Air bag - fascia - passenger - up to 04MY ...................................................................................... 75-14
Air bag - fascia - passenger - from 04MY ....................................................................................... 75-15
Diagnostic control unit (DCU) ........................................................................................................ 75-16
Airbag - passenger - deployment - off vehicle ............................................................................... 75-17
Rotary coupler - (SRS) air bag system ........................................................................................... 75-19
Airbag module - steering wheel - deployment - off vehicle ............................................................ 75-20
Airbag module - steering wheel - deployment - in-vehicle .............................................................. 75-21
Pre-tensioner - front seatbelt - deployment - in-vehicle .................................................................. 75-23
DOORS...................................................................................................... 76-1-1
ADJUSTMENTS
Door - front or rear - adjust on striker ............................................................................................ 76-1-1
Door - front - align on hinges .......................................................................................................... 76-1-2
REPAIRS
Door assembly - front - remove for access & refit .......................................................................... 76-1-3
Door assembly - rear - remove for access & refit ........................................................................... 76-1-4
Door - tail assembly - remove for access & refit ............................................................................. 76-1-5
Glass - front door .......................................................................................................................... 76-1-6
Glass - rear door ............................................................................................................................ 76-1-7
Rubber/felt - glass channel - front door ........................................................................................ 76-1-8
Rubber/felt - glass channel - rear door .......................................................................................... 76-1-9
Glass - tail door .............................................................................................................................. 76-1-10
Quarter light - rear door .................................................................................................................. 76-1-11
Glass regulator - tail door .............................................................................................................. 76-1-12
Seal - waist inner - tail door ............................................................................................................ 76-1-13
Trim casing - front door - 3 door .................................................................................................... 76-1-14
Trim casing - front door - 5 door - up to 04MY................................................................................ 76-1-15
Trim casing - front door - 5 door - from 04MY ................................................................................ 76-1-16
Trim casing - rear door - up to 04MY .............................................................................................. 76-1-18
Trim casing - rear door - from 04MY............................................................................................... 76-1-20
Trim casing - tail door ..................................................................................................................... 76-1-22
Plastic sheet - front door - lower - 3 door........................................................................................ 76-1-23
Pocket - front door - 3 door ............................................................................................................. 76-1-23
Plastic sheet - front door - upper - 3 door ....................................................................................... 76-1-24
Plastic sheet - tail door ................................................................................................................... 76-1-24
Plastic sheet - front door - 5 door .................................................................................................. 76-1-25
Plastic sheet - rear door.................................................................................................................. 76-1-25
Latch - front door - 3 door ............................................................................................................... 76-1-26
Latch - front door - 5 door .............................................................................................................. 76-1-27
Latch - rear door ............................................................................................................................. 76-1-28
Latch - tail door ............................................................................................................................... 76-1-29

GENERAL INFORMATION
03-28
SRS component replacement policy
The following information details the policy for
replacement of SRS components; either as a result
of a vehicle accident or as a result of vehicle age.
Impacts which do not deploy the airbags or seat
belt pre-tensioners
Check for structural damage in the area of the
impact, paying particular attention to bumper
armatures, longitudinals, crash cans and bracketry.
Impacts which deploy the airbags and/or seat
belt pre-tensioners
The inspection and replacement policy is dependent
on the type and severity of the crash condition. The
following guidelines are the minimum that should be
exercised as a result of the deployment of specific
SRS components.
Front airbag/ seat belt pre-tensioner deployment
(driver and passenger)
If the front airbags and/or seat belt pre-tensioners are
deployed as a result of a front, front angled or side
impact, the following parts must be replaced:
lDriver airbag module
lPassenger airbag module (where fitted)
lSRS flyleads
lSRS DCU
lRotary coupler
lFront seat belt pre-tensioners
In addition, the following should be inspected for
damage and replaced as necessary:
lFront seat belt and buckle tongue (anchorage
points, webbing etc.)
lFascia moulding adjacent to passenger airbag
module (where fitted)
lSteering wheel (if damage is evident)
lFront seat frames and head restraints (if there is
evidence of damage to the seat frame or
cushion pan)
lSteering column (if adjustment is lost or there
are signs of collapse)
lFront seat belt height adjusters on 'BC' posts (5
door models only)
lRear seat belts and seat belt buckles (webbing,
buckle covers, body anchorage and tongue
latching function)Rear Impact
If the seat belt pre-tensioners are deployed during a
rear impact, the following components must be
replaced:
lSeat belt pre-tensioners
lFront and rear automatic seat belt assemblies
used during an impact.
lSRS DCU
In addition, the following components should be
inspected for damage and replaced as necessary:
lFront seat frames
lFront seat belts and buckle (retractors,
webbing, tongue latching, buckle covers, body
anchorages and 'D' loops)
lSeat belt height adjusters (5 door models only)
lRear seat belts and seat belt buckles (webbing,
buckle covers, body anchorage and tongue
latching function)
Periodic replacement of SRS components
The performance of the propellants within airbags
and seat belt pre-tensioners will deteriorate over a
period of time. As a result, it is essential that the
airbags and seat belt pre-tensioners are periodically
replaced to maintain occupant safety. Airbags, seat
belt pre-tensioners and the rotary coupler should be
replaced at the recommended intervals.

MAINTENANCE
MAINTENANCE 10-7
Tyres
Check
1.Check for any apparent damage to tyres,
paying particular attention to side walls.
2.Look at tyre treads and check for any unusual
wear patterns which may indicate out of
specification adjustment of steering or
suspension.
NOTE: Any adjustments to steering or
suspension will be subject to additional labour
and/or material cost and should not be carried
out without the authorisation of the customer.
3.Measure the tread depth across the width of the
tyre and around the circumference. Annotate
the maintenance check sheet with the lowest
figure obtained from each tyre.
NOTE: Any requirement to replace tyres should
be advised to the customer before any remedial
work is carried out. This will be subject to
additional labour and/or material cost and
should not be carried out without the
authorisation of the customer.
CAUTION: If new tyres are to be fitted,
ensure that they are fitted to the rear axle
only or to both front and rear axles. DO NOT
fit new tyres to front axle only.
Brake Pads and Calipers
Brake Pads
1.With front road wheels removed, check brake
pad thickness and ensure that both pads are
wearing evenly.
2.Check brake discs for signs of cracking,
excessive scoring or oil contamination.
NOTE: Any requirement to replace brake pads
or brake discs should be advised to the
customer as this will be subject to additional
labour and/or material cost and should not be
carried out without the authorisation of the
customer.
3.Check for any signs of brake fluid leakage from
caliper seals, hoses or unions.
4.Using brake cleaner, remove excessive
deposits of brake dust from pads, calipers and
disc shields.

ENGINE - K SERIES KV6
REPAIRS 12-3-33
71.Remove 3 bolts securing PAS pump to front
mounting plate and tie pump aside.
72.With assistance, manoeuvre and lower engine
and gearbox to floor.
Refit
1.With assistance, raise engine and gearbox into
engine compartment.
2.Position PAS pump to front mounting plate, fit
and tighten bolts to 25 Nm (18 lbf.ft).
3.Position PAS pump pulley, fit and tighten Torx
screws to 9 Nm (7 lbf.ft).
4.Position top arm to engine mounting bracket
and RH hydramount, fit and tighten bolts to 100
Nm (74 lbf.ft).
5.Position PAS pipe support bracket to RH
hydramount, fit and tighten nut to 85 Nm (63
lbf.ft).
6.Place a wooden block on jack, position jack
under gearbox and raise jack sufficient to
support weight of gearbox. Release lifting hook
from lifting bracket on gearbox and connect to
rear engine lifting bracket.
7.Lower and remove jack supporting gearbox.
8.Remove bolts securing LRT-44-026 lifting
bracket to gearbox and remove bracket.
9.Position LH mounting bracket to gearbox, fit
and tighten bolts to 85 Nm (63 lbf.ft).
10.Position LH mounting to body, fit and tighten
bolts to 48 Nm.
11.Align gearbox bracket to LH body mounting, fit
and tighten through bolt to 100 Nm (74 lbf.ft).
12.Position upper RH engine steady to top arm, fit
and tighten bolt to 100 Nm (74 lbf.ft).
13.Tighten bolt securing upper RH engine steady
to body to 100 Nm (74 lbf.ft).
14.Position PAS pipe to engine front mounting
plate, fit and tighten bolt to 25 Nm (18 lbf.ft).
15.Lower hoist, disconnect and remove lifting
bracket, LRT-12-138.
16.Raise vehicle on ramp.17.Position A/C compressor to front mounting
plate and cylinder block, align heat shield, fit
and tighten bolts to 25 Nm (18 lbf.ft).
18.Connect multiplug to A/C compressor.
19.Using a 3/8 square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
20.Position selector cable to gearbox bracket and
secure with clip.
21.Position selector lever to selector shaft, fit and
tighten nut to 25 Nm (18 lbf.ft).
22.Clean splines and seal areas on each
driveshaft and mating faces in front hubs.
23.Fit new circlips to RH and LH driveshaft inner
joint splines.
24.Fit driveshafts to IRD and gearbox, ensuring
that the circlip on each driveshaft is fully
engaged.
25.Engage LH and RH driveshafts into front hubs.
26.Fit new driveshaft flange nuts but do not tighten
at this stage.
27.Clean ball joint tapers and taper seats.
28.Position LH and RH track rod ends to steering
arms, fit new nuts and tighten to 55 Nm (40
lbf.ft).
29.Clean ABS sensors and mating faces.
30.Apply anti-seize grease to both ABS sensors
and position sensors in front hubs.
Ensure ABS sensor is fully located into hub,
so that sensor touches pole wheel teeth.
31.Position LH and RH brake hoses to front
damper brackets and secure with clips.
32.Position LH and RH splash shields, fit and
tighten bolts.
33.Ensure mating face of propeller shaft and IRD
drive flange are clean.
34.Fit propeller shaft to IRD flange and align
marks. Tighten nuts and bolts to 42 Nm (31
lbf.ft).
35.Fit rear beam.

+ FRONT SUSPENSION, REPAIRS,
Rear beam.
36.Fill IRD to correct level with fluid.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) fluid - drain & refill -
Non NAS.

+ INTERMEDIATE REDUCTION
DRIVE, ADJUSTMENTS, Intermediate
reduction drive (IRD) lubrication system -
drain & refill - NAS.
37.Fit exhaust front pipe.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - Non
NAS.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, REPAIRS, Front pipe - NAS.

STEERING
57-2 ADJUSTMENTS
Front wheel alignment - check & adjust
$% 57.65.01
Check
1.Ensure tyre pressures are correct and vehicle
is at kerbside weight.
2.Roll vehicle backwards and forwards to relieve
stresses in steering and suspension.
3.Ensure that wheel alignment equipment is
properly calibrated.
4.Check front wheel alignment is within
tolerance.

+ GENERAL DATA, Steering.
Adjust
1.Mark position of steering ball joints for
reference.
2.Loosen track rod and ball joint pinch bolts.3.Rotate turn buckle to obtain correct alignment.
Ensure ball joint is not rotated.
CAUTION: Both track rods must be rotated
an equal amount.
4.Recheck front wheel alignment.
5.Tighten track rod and ball joint pinch bolts to 28
Nm (21 lbf.ft).
CAUTION: Ensure slots in turn buckle
clamps are aligned.

STEERING
ADJUSTMENTS 57-3
Alignment - rear wheel - check & adjust
$% 57.65.06
Check
1.Ensure tyre pressures are correct and vehicle
is at kerbside weight.
2.Roll vehicle backwards and forwards to relieve
stresses in steering and suspension.
3.Ensure that wheel alignment equipment is
properly calibrated.
4.Check front wheel alignment is within
tolerance.

+ GENERAL DATA, Steering.
5.Check rear wheel alignment is within tolerance.

+ GENERAL DATA, Steering.Adjust
1.Hold turnbuckle on adjustable link and loosen
both lock nuts.
2.Rotate turnbuckle to obtain correct alignment.

+ GENERAL DATA, Steering.
3.Hold turnbuckle and tighten lock nuts to 90 Nm
(66 lbf.ft).
4.Roll vehicle backwards and forwards to relieve
stress in suspension.
5.Repeat check and adjust procedure on other
side of vehicle.

STEERING
57-4 ADJUSTMENTS
Power steering - pressure test
$% 57.90.10.01
Check
1.Position absorbent cloth to catch spillage.
2.Remove bolt securing PAS high pressure pipe
clip to PAS pump.
3.Loosen union securing high pressure pipe to
PAS pump and release pipe.
4. K1.8 models: Fit adaptor LRT-57-034A to high
pressure port of PAS pump.
5. KV6 & Td4 models: Fit adaptor LRT-57-042 to
high pressure port of PAS pump.
6.Fit adaptor LRT-57-035 to existing high
pressure hose.
7.Fit hose LRT-57-002 to each adaptor.
8.Fit pressure gauge LRT-57-005 to test valve
LRT-57-001
9.Connect hoses LRT-57-002 to LRT-57-001
and tighten unions.
10.Ensure steering system and test equipment is
free from leaks.
11.Maintain maximum fluid level during test.
12.With the test valve open, start the engine.
13.Pressure at idle should be between 5 and 7
bar.
14.With the engine at idle, slowly turn the steering
wheel and hold on full lock.
15.Repeat procedure for other side.
16.Test pressure should rise significantly as
steering wheel is rotated and continue to rise as
full lock is approached. For full lock pressures,
refer to general data section.

+ GENERAL DATA, Steering.
17.With the engine at idle, release steering wheel.
For idle pressure, refer to general data section.

+ GENERAL DATA, Steering.
18.Pressures outside the above tolerance
indicates a fault.19.To determine if fault is in steering pump or
steering rack, close the test valve for a
maximum of 5 seconds.
CAUTION: Pump damage will occur if test
valve is closed for longer periods.
20.If gauge does not register correct reading,
suspect faulty pump.
21.If PAS pump pressure is correct and steering is
heavy at idle and becomes light as engine RPM
is increased, suspect pump flow rate.
22.If maximum pump pressure is correct, suspect
steering rack.
23.On completion stop engine and remove test
equipment.
24.Clean PAS pump and pipe union.
25.Fit new 'O' ring to high pressure pipe, align to
PAS pump and tighten union to 25 Nm (18
lbf.ft).
26.Fit bolt securing high pressure pipe clip and
tighten to 8 Nm (6 lbf.ft).
27.Check and top-up PAS fluid level.

+ MAINTENANCE, MAINTENANCE,
Intermediate Reduction Drive - Non NAS
models.