2001 LAND ROVER FREELANDER jacking

CONTENTS
CONTENTS 3
TORQUE WRENCH SETTINGS .............................................................. 06-1
Maintenance ................................................................................................................................... 06-1
Engine – Td4................................................................................................................................... 06-2
Engine – K1.8 ................................................................................................................................. 06-4
Engine – KV6 .................................................................................................................................. 06-6
Emission Control ............................................................................................................................. 06-8
Engine Management System – EDC .............................................................................................. 06-9
Engine Management System – MEMS ........................................................................................... 06-10
Engine Management System – Siemens ........................................................................................ 06-11
Fuel Delivery System – Diesel ........................................................................................................ 06-12
Fuel delivery system – Petrol .......................................................................................................... 06-13
Cooling System – Td4..................................................................................................................... 06-14
Cooling System – K1.8 ................................................................................................................... 06-14
Cooling System – KV6 .................................................................................................................... 06-14
Manifolds and Exhaust System – Td4 ............................................................................................ 06-15
Manifolds and Exhaust Systems – K1.8 ......................................................................................... 06-16
Manifolds and Exhaust Systems – KV6 .......................................................................................... 06-17
Clutch .............................................................................................................................................. 06-18
Manual Gearbox – PG1 .................................................................................................................. 06-19
Manual Gearbox – Getrag .............................................................................................................. 06-20
Intermediate Reduction Drive ......................................................................................................... 06-21
Automatic Gearbox – Jatco ............................................................................................................. 06-22
Driveshafts ...................................................................................................................................... 06-23
Rear Axles and Final Drive ............................................................................................................. 06-24
Steering........................................................................................................................................... 06-25
Front Suspension and Subframe .................................................................................................... 06-26
Rear Suspension and Subframe ..................................................................................................... 06-27
Brakes ............................................................................................................................................. 06-28
Supplementary Restraint Systems .................................................................................................. 06-29
Body ................................................................................................................................................ 06-30
Heating and Ventilation ................................................................................................................... 06-32
Air Conditioning............................................................................................................................... 06-33
Wipers and Washers ....................................................................................................................... 06-34
Electrical ......................................................................................................................................... 06-35
LIFTING AND TOWING ........................................................................... 08-1
Jacking ............................................................................................................................................ 08-1
Towing ............................................................................................................................................ 08-2
Emergency starting ......................................................................................................................... 08-4
CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS ...................... 09-1
Capacities ....................................................................................................................................... 09-1
Fluids .............................................................................................................................................. 09-2
Lubrication ...................................................................................................................................... 09-3
Sealants .......................................................................................................................................... 09-4

GENERAL INFORMATION
03-2
Environmental Protection Precautions
It is illegal to pour used oil on to the ground, down
sewers or drains, or into water courses.
Burning of used engine oil in small space heaters or
boilers should only be considered for units of
approved design and in compliance with the
equipment manufacturer's recommendations. The
heating system must meet the regulatory standards
of HMIP for small burners of less than 0.4 MW. If in
doubt check with the appropriate local authority and/
or manufacturer of the approved appliance.
Dispose of used oil and filters through authorised
waste disposal contractors and licensed waste
disposal sites, or through the waste oil reclamation
trade. If in doubt, contact the Local Authority for
advice on disposal facilities.
Safety instructions
Whenever possible, use a lift or pit when working
beneath vehicle, in preference to jacking. Chock
wheels as well as applying parking brake.
Jacking
Always use the recommended jacking points. The
recommended jacking points are shown in
theLIFTING AND TOWING sub-section of the
INFORMATION section.
Always ensure that any lifting apparatus has
sufficient load capacity for the weight to be lifted.
Ensure the vehicle is standing on level ground prior
to lifting or jacking.
Apply the handbrake and chock the wheels.
WARNING: Do not work on or under a vehicle
supported only by a jack. Always support the
vehicle on safety stands.
Do not leave tools, lifting equipment, spilt oil, etc.,
around or on the work bench area. Always keep a
clean and tidy work area.
Brake shoes and pads
Always fit the correct grade and specification of
brake linings. When renewing brake pads and brake
shoes always replace as complete axle sets only.

LIFTING AND TOWING
08-1
LIFTING AND TOWING
Jacking
The following instructions must be carried out before
raising the vehicle off the ground:
lUse a solid level surface.
lApply parking brake.
lSelect 1st. gear in main gearbox and ensure
HDC is not selected.
CAUTION: To avoid damage to under body
components of the vehicle, adhere to the
following jacking procedures:
DO NOT POSITION JACKS OR AXLE STANDS
UNDER THE FOLLOWING COMPONENTS:
lBumpers
lBrake or Fuel lines
lExhaust pipe
lSuspension components
lSteering rack and linkages
lFuel tank
lEngine sump
lGearbox
lIRD unit
Jack or support vehicle only on approved jacking
points as detailed in the following illustration:
Front (hydraulic jack) and side (vehicle jack) jacking
pointsSafety stand positions under longitudinal members
Rear (hydraulic jack) and side (vehicle jack) jacking
points
Vehicle jack
The jack provided with the vehicle is only intended to
be used in an emergency, for changing a tyre. Do
NOT use the jack for any other purpose. Refer to the
Owner's Handbook for vehicle jack location points
and procedure. Never work under a vehicle only
supported by the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500 kg (3,300 lbs)
load capacity must be used.
WARNING: Do not work on or under a vehicle
supported only by a jack. Always support the
vehicle on safety stands.

EXTERIOR FITTINGS
76-2-16 REPAIRS
Finisher - sill - lower
$% 76.43.28
Remove
1.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
2.Remove both jacking point covers.
3.Remove 7 scrivets securing sill finisher to body.
4.Release and remove finisher from sill.Refit
1.Clean mating faces of finisher.
2.Position finisher to sill, locate over jacking
points and secure with scrivets.
3.Fit jacking point covers.
4.Remove stands and lower vehicle.

CORROSION PREVENTION AND SEALING
SEALING 77-4-9
Inspections during maintenance servicing
It is a requirement of the Corrosion Warranty that the vehicle body is checked for corrosion by an authorised Land
Rover Dealer at least once a year, to ensure that the factory-applied protection remains effective.
Service Job Sheets include the following operations to check bodywork for corrosion:
lWith the vehicle on a lift, carry out visual check of underbody sealer for damage.
lWith the vehicle lowered, inspect exterior paintwork for damage and body panels for corrosion.
The vehicle must be washed and free from deposits prior to inspection. It is part of the owner's responsibility to ensure
that the vehicle is kept free of accumulations of mud which could accelerate the onset of corrosion. It will be necessary
for the vehicle to be washed by the Dealer prior to inspection of bodywork if the customer has offered the vehicle in
a dirty condition. Particular attention should be paid to areas where access is difficult.
The checks described above are intended to be visual only. It is not intended that the operator should remove trim
panels, finishers, rubbing strips or sound-deadening materials when checking the vehicle for corrosion and paint
damage.
With the vehicle on a lift, and using an inspection or spot lamp, visually check for the following:
lCorrosion damage and damaged paintwork, condition of underbody sealer on front and rear lower panels, sills
and wheel arches.
lDamage to underbody sealer. Corrosion in areas adjacent to suspension mountings and fuel tank fixings.
The presence of small blisters in underbody sealer is acceptable, providing they do not expose bare metal.
Pay special attention to signs of damage caused to panels or corrosion protection material by incorrect jack
positioning.
caut : It is essential to follow the correct jacking and lifting procedures.
With the vehicle lowered, visually check for evidence of damage and corrosion on all visible painted areas, in
particular the following:
lFront edge of bonnet.
lVisible flanges in engine compartment.
lLower body and door panels.
Rectify any bodywork damage or evidence of corrosion found during inspection as soon as is practicable, both to
minimise the extent of the damage and to ensure the long term effectiveness of the factory-applied corrosion
prevention treatment. Where the cost of rectification work is the owner's responsibility, the Dealer must advise the
owner and endorse the relevant documentation accordingly.
Where corrosion has become evident and is emanating from beneath a removable component (e.g. trim panel,
window glass, seat etc.), remove the component as required to permit effective rectification.