2001 HONDA CIVIC COUPE Owners Manual

Check the f ollowing:
If youfindanybulbsareburnedout,
replace them as soon as possible.
Refer to the chart on page to
determinewhattypeof replacement
bulb is needed.Headlights (low and high beam)
Parking lights
Taillights
Brake lights
High-mount stop light
Turn signals
Back-up lights
Hazard light f unction
License plate light
Side marker lights
Daytime running lights
(Canadian models)
295
Lights
Maint enance246
B BAA C
CKK--U
UP P L
LIIGGH HT
T
S
ST TO
OP P/
/T
T A
A I
ILLL LIIGGH HT
T
S
SI
IDD E
E M
M A
AR
RKKEER
R L
LIIGGH HT
T H
HI
IGGH H-
-M
M O
OUUNNTT
S
ST TO
OP P L
LIIGGH HT
T
T
T
U
UR RNN S
SIIGGN NAAL
L L
LIIGGH HT
T
L
LIICCE EN
NS SEE P
PL
LAA T
TE
E
L
LI IGGH HT
TS
S

Open the hood.
If you need to change the head-
light bulb on the driver’s side,
remove the power steering
reservoir tank by pulling it out of
its holder.
Your car has halogen headlight
bulbs, one on each side. When
replacing a bulb, handle it by its steel
base and protect the glass from
contactwithyourskinorhard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Theheadlightswereproperlyaimed
when your car was new. If you
regularly carry heavy items in the
trunk, readjustment may be required.
Adjustment of the headlights should
be perf ormed by a Honda technician
or other qualif ied mechanic.
1.
CONT INUED
Replacing a Headlight Bulb
Headlight A iming
Lights
Maint enance247
H H O
OL LDD E
ER
R
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Reinstall the power steering
reservoir. (Driver’s side) Push the electrical connector onto
the tabs of the new bulb. Make
sure it locks in place.
Turn on the headlights to test the
new bulb. Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place and clip the end into
the slot.
Install the rubber seal over the
back of the headlight assembly.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way and remove the bulb. Remove the rubber weather seal
by pulling on the tab. Remove the electrical connector
f rom the bulb by squeezing the
connector on both sides to unlock
the tab. Pull the connector straight
off.
3.
4. 5.
6.
7.
8.
1.
2. Replacing the Front Side Marker/
Turn Signal and Parking L ight
Bulb
Lights
Maint enance248
W WE
EA
A T
TH
H E
ER
R S
SEEA
A L
L B
BUUL LBB
C
CO ON NNNEEC
CT TO
OR R H
HO
OL LDD -
-D
D O
OW WN N W
WIIRRE E

Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
Pull the inner f ender cover back.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
3. 2. 4.
5.6.
7.
8.
Lights
Maint enance249
H H
O
OL LDD I
INNG G C
CLLIIPP

Open the trunk.Determine which of the two bulbs
is burned out: stop/taillight/side
marker light or turn signal light.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Remove the socket by turning it
one-quarter turn counterclockwise. Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
Remove the screw in the center of
the fastener on the side of the
trunk lining. Pull the lining back. Put the f astener into the hole on
the side of the trunk lining.
Reinstall the screw.
1.
2.
3.4.
5.
6.
7.
8.
Replacing Rear Bulbs
(in Fenders)
Lights
Maint enance250
F FA
A S
STTE
EN
NE ER
R

Remove the socket f rom the light
assembly by squeezing the tabs on
both sides of the socket.
Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.
Reinstall the socket. Turn it
clockwise until it locks. Make sure
the new bulb is working.
Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Push the new bulb straight into
the socket until it bottoms. Pull the bulb straight out of its
socket. 2. 1.
3.
2. 1.
CONT INUED
Replacing a Rear L icense Plate
Bulb
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance251

Put the light assembly back into
thehole,rightsidefirst.Pushon
the lef t side until it snaps into
place. Pull the bulb straight out of the
holder. Push the new bulb straight
into the holder until it bottoms.
Remove the trunk light assembly
by using a small f lat-tipped
screwdriver to pry caref ully on the
lef t edge of the assembly.
Turn on the parking lights and
check that the new bulb is
working.
Reinstall the socket back in place
by pushing it in until it latches.
2.
3.
1.
3.
4.
Replacing the T runk L ight Bulb
Lights
Maint enance252

Removethelensbycarefully
prying on the edge of the lens in
the middle with a f ingernail f ile or
a small f lat-tip screwdriver. Do not
pry on the edge of the housing
around the lens.
Although the ceiling light and
spotlights come apart the same way,
theydonotusethesametypeof
bulbs.
Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs. Snap the lens back in place.
Spotlights:
Pry on the edge between the lenses.
2.
3.
1.
On LX models
Replacing Bulbs in the Interior
Lights
Lights
Maint enance253
C CE EI
ILLI INNG G L
LIIGGH HT
T
F
FRRO ON NTT C
CEEI
ILLI INNG G L
LIIGGH HT
T
L
LXX
S
SP
PO
OT TL
LIIGGH HT
TS
S
U
U. .SS. .:: E
E X
X ,
,C
Ca ann a
add a
a::S
Si i