Page 17 of 36
EN/17Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0
The figure shows the boot on the left."
Thread the basic wiring harness A with branches
A6 to A13 and A15, as shown in the figure, through
the passage grommet (20) along the standard
wiring harness to the boot and secure it with cable
ties (3).
0Disconnect the white 12-pin plug connector X322.
Insert branch A12, white 12-pin plug casing, and
branch A13, white 12-pin socket casing on the
basic wiring harness between the above
connectors.
Secure the new plug connectors A13+X322S and
A12+X322B, as shown in the figure.
0Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them if necessary.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
0Cars without an on-board monitor radio only
Insulate branch A9, black 12-pin plug casing,
branch A10, socket contact, white/brown cable,
and branch A15, socket contact, white/green
cable, on the basic wiring harness A and tie them
back on the standard wiring harness.
Branches A9, A10 and A15 are no longer
required.
"
20
A
3
A11
A6
A13
A12A8
A7
A9A10
A15
F 39 0978 B
A12 X322S
A13
X322B
A
F 39 0979 B
A6
4A7
F 39 0980 B
A
A9 A10
A15
F 39 0982 B
Page 18 of 36
EN/18Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0Cars with an on-board monitor radio only
Disconnect the black 12-pin plug casing X13598
from the on-board monitor radio connection plug
(20) and tie it back.
Connect branch A9, black 12-pin plug casing, into
the cleared slot (21) in the on-board monitor radio
connection plug (20).
If the car does not have a black 12-pin plug
casing X13598, branch A9 must be
connected direct.
"
0
This step only applies to cars without an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10 of
the 8-pin plug casing X18126.3
Connect branch A10, socket contact, white/brown
cable, to the free slot in the on-board monitor radio
connection plug (20) PIN10 on the 8-pin plug
casing X18126.
0
This step only applies to cars with an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10
of the 8-pin plug casing X18126.3
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the on-board monitor radio connection plug (20).
Cut off the basic wiring harness A near branch
A10.
Connect branch A10, socket contact, white/brown
cable, to the supply cable of the on-board monitor
radio connection plug (20) PIN10, white/brown
cable, on the 8-pin plug casing X18126 using a
2-way insulation-piercing connector (1).
20
20 21 A9 X13598
F 39 0983 B
20
F 39 0985 B
A10
X18126/PIN10
20
20
F 39 0986 B
A10
211
20
X18126
Page 19 of 36
EN/19Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0Cars with an on-board monitor radio only
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Connect branch A15, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin
plug casing X18126.
"
Cut off the basic wiring harness A near branch
A15.
Connect branch A15, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0Only required for cars without earth post
X10305 with a production date after 9/00
Remove the left tail light.
Mark the drilling position (20) with a centre punch.
Dimension A= 19 mm
Dimension B = 17 mm
Remove the body paint and primer from the grey
area (21) in a diameter of 20 mm around the
position of the hole (20) on the front and rear of the
tail light unit (22).
The panel must be bare in the grey area (21), to
ensure that perfect contact is possible.
Risk of damage. Before drilling the hole
ensure that the cable and plug fastenings are
unclipped and the cables are removed from
the drilling area to prevent their being
damaged.
"
Drill the holes with a 6 mm drill bit.
Remove all the drill chips that are produced during
the drilling process using an extractor.
Then deburr the edges of the hole.
20
039 0003 B
A15
X18126/PIN11
20
20
039 0004 B
A15
211
20
X18126
F 39 0992 B21
22
A B
20 21
Page 20 of 36
EN/20Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0Insert the hexagonal screw with collar (11) from the
rear into the hole (20) and secure it with a nut M6
(13).
If you fit the earth connection cable later, ensure
that you fit the washer (12) first and then branch
A11.
Then secure branch A11 (the cable outlet on the
terminal lug must point downwards) with the
second nut M6 (13).
After securing the parts, treat all of them with
the anti-corrosion measures set out in the
BMW standard.
"
0
The figure shows the final installation position
of the earth connection cable.
"
The cable loom (20) must point downwards.
0Applies to all E39 cars
Remove the left tail light.
Mark the drilling position (20) with a centre punch.
The figure shows the left lamp holder, on cars
without a lamp holder proceed in exactly
the same way.
"
Insert the 5A fuse (2) into the fuse holder A8.
Secure the fuse holder A8 to the wiring harness
near the left tail light with a cable tie (3).
F 39 0993 B
20
13
13 12 11
A11
20
F 39 0994 B
A83 2
5A
F 39 0984 B
Page 21 of 36
EN/21Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply harness BE39/2 cars
only
0
The figure shows the installation space near
the handbrake lever.
"
Carefully cut out the opening (20) in the carpet (21)
in front of the handbrake lever (22).
Pull up the carpet at the rear (21) on the driver’s
side and lay branches A1 to A4 and A14 on the
basic wiring harness A forwards to the gearshift
lever under the centre console.
0Lay branch A1, coaxial socket casing FME on the
basic wiring harness A under the centre console
(20) into the passenger’s footwell.
Lay branch A4, black 18-pin socket casing on the
basic wiring harness A, as shown in the figure,
under the centre console oddments box at the
front.
Connect branch A4 to the required adapter
cable for the hands-free kit.
"
0
In cars with an on-board monitor radio,
insulate and tie back branches A2, A3 and
A14.
"
Lay branch A2, black 12-pin plug casing, branch
A3, socket contact, white/brown cable, and
branch A14, socket contact, white/green cable, on
the basic wiring harness A to the installation site of
the radio.
21
22
F 39 0971 B
A1-A4+A14
21
20 A
A1 20
A4
A
F 39 0972 B
20 A3 A2
A
A14
F 39 0976 B
Page 22 of 36
EN/22Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0Cars without an on-board monitor radio only
Disconnect the black 12-pin plug casing X13598
from the radio connection plug (20) and tie it back.
Connect branch A2, black 12-pin plug casing, to
the cleared slot (21) in the radio connection plug
(20).
If the car does not have a black 12-pin plug
casing X13598, branch A2 must be
connected direct.
"
0
This step only applies to cars without an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
Connect branch A3, socket contact, white/brown
cable, to the free slot in the radio connection plug
(20) PIN10 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the radio connection plug (20).
Cut off the basic wiring harness A near branch A3.
Connect branch A3, white/brown cable, to the
supply cable of the radio connection plug (20)
PIN10, white/brown cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
20 21
20
A2
A2 X13598
F 39 0973 B
20
F 39 0974 B
A3
X18126/PIN10
20
20
F 39 0975 B
A3
211
A
20 X18126
Page 23 of 36
EN/23Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0Cars without an on-board monitor radio only
This step only applies to cars without an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.
"
Connect branch A14, socket contact, white/green
cable, to the free slot in the radio connection plug
(20) PIN11 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing TEL ON cable on the radio
connection plug (20) PIN11 of the 8-pin plug
casing X18126.3
Cut off the basic wiring harness A near branch
A14.
Connect branch A14, white/green cable, to the
supply cable of the radio connection plug (20)
PIN11, white/green cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
0Applies to all E39/2 cars
The figure shows the area with the removed
driver’s seat.
"
Pull up the driver's side carpet at the rear (20) and
lay the basic wiring harness A as shown in the
figure and secure it with textile adhesive tape (21).
Lay branch A5, black 3-pin socket casing, along
the left door sill towards the front.
0Thread branch A5, black 3-pin socket casing on
the basic wiring harness A near the left A pillar
through the instrument panel from below and
along the left A pillar upwards to the headlining
and secure it with textile adhesive tape.
As you lay branch A5 to the microphone
installation site, ensure that the cable is
properly routed in the cable duct to prevent
any impairment of the head airbag
function.
"
See instructions for head airbag."
20
039 0001 B
A14
X18126/PIN11
20
20
039 0002 B
A14
211
A
20 X18126
21
21
A
A520
F 39 0977 B
F 39 0981 BIIIIIIIIIIIIIIIIIIIIIIIIIIIII
A5
A
!
!
Page 24 of 36
EN/24Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
The figure shows the boot on the left."
Lay the basic wiring harness A, as shown in the
figure, with branches A6 to A13 and A15 along the
standard wiring harness and secure it with cable
ties (3).
0Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
0Connect branch A12, white 12-pin plug casing
on the basic wiring harness A to branch B1, white
12-pin socket casing on the power supply wiring
harness B.
Tie back plug connector A12 + B1 on the standard
wiring harness.
0Insulate branch A13, white 12-pin socket casing
and tie it back on the standard wiring harness (no
longer required).
F 39 0997 B
A7A63A12
A13A11
A10
A9
A8
A15
4
A6 A7
F 39 0998 B
A12A
B1B
F 39 0999 B
A13
F 39 1000 B
