2001 BMW 5 SERIES length

EN/10Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
5. Installation and cabling diagram for basic wiring harness A in E39 cars
0
The basic wiring harness A is to be installed along the audio and main wiring harness as shown
in the figure and secured using textile adhesive tape and cable ties.
Start the installation of the basic wiring harness A at point 1 (next to the handbrake lever)
with branches A1 to A4.
Branch A1 to the footwell on the right
Branches A2, A3 and A14 to the installation site of the radio (insulate and tie back in cars with
an on-board monitor radio)
Branch A4 next to the gearshift lever on the left (under the oddments box in the centre console
at the front)
Branch A5 to the installation site of the microphone in the headlining at the front centre
Branch A6 to the installation site of the compensator in the boot on the left
Branch A7 to the installation site of the compensator in the boot on the left or to the connector
for the telephone aerial in the boot on the left
Branch A8 to the left tail light wiring harness
Branches A9, A10 and A15 to the on-board monitor radio in the boot on the left (insulate and
tie back in cars without an on-board monitor radio)
Branch A11 to earth post X10305 under the left tail light
Branch A12 to plug connector X322 in the boot on the left
Branch A13 to plug connector X322 in the boot on the left
Tie back any excess lengths.
A6+A7A12+A13
A8-A11
A1
A2+A3
A3A4
A5A
Punkt 1Punkt 1
A14
A15
F 39 0965 B

EN/11Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
6. Installation and cabling diagram for basic wiring harness A and power supply
wiring harness B in E39/2 cars
0
The basic wiring harness A is to be installed along the audio and main wiring harness as shown
in the figure and secured using textile adhesive tape and cable ties.
Start the installation of the basic wiring harness A at point 1 (next to the handbrake lever)
with branches A1 to A4.
Branch A1 to the footwell on the right
Branches A2, A3 and A14 to the installation site of the radio (insulate and tie back in cars with
an on-board monitor radio)
Branch A4 next to the gearshift lever on the left (under the oddments box in the centre console
at the front)
Branch A5 to the installation site of the microphone in the headlining at the front centre
Branch A6 to the installation site of the compensator in the boot on the left
Branch A7 to the installation site of the compensator in the boot on the left or to the connector
for the telephone aerial in the boot on the left
Branch A8 to the left tail light wiring harness
Branches A9, A10 and A15 to the on-board monitor radio in the boot on the left (insulate and
tie back in cars without an on-board monitor radio)
Branch A11 to earth post X13016 under the left tail light
Branch A12 to branch B1 on the power supply wiring harness B in the boot on the left
Branch A13 - insulate and tie back
Power supply wiring harness B
Branch B1 to branch A12 on the basic wiring harness A in the boot on the left
Branch B2 to plug connector X322 in the boot on the left
Branch B3 to plug connector X325 in the boot on the right above the power distributor
Branch B4 to plug connector X325 in the boot on the right above the power distributor
Tie back any excess lengths.
A6+A7
A8+A11 A12+A13
A9+A10
A1
A2+A3
A3A4
A5
Punkt 1Punkt 1
B1
B
B4
B3
B2
A
A14
A15
F 39 0966 B

EN/15Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0
This step only applies to cars without an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
Connect branch A3, socket contact, white/brown
cable, to the free slot in the radio connection plug
(20) PIN10 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the radio connection plug (20).
Cut off the basic wiring harness A near branch A3.
Connect branch A3, white/brown cable, to the
supply cable of the radio connection plug (20)
PIN10, white/brown cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
20
F 39 0974 B
A3
X18126/PIN10
20
20
F 39 0975 B
A3
211
A
20 X18126

EN/17Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0
The figure shows the boot on the left."
Thread the basic wiring harness A with branches
A6 to A13 and A15, as shown in the figure, through
the passage grommet (20) along the standard
wiring harness to the boot and secure it with cable
ties (3).
0Disconnect the white 12-pin plug connector X322.
Insert branch A12, white 12-pin plug casing, and
branch A13, white 12-pin socket casing on the
basic wiring harness between the above
connectors.
Secure the new plug connectors A13+X322S and
A12+X322B, as shown in the figure.
0Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them if necessary.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
0Cars without an on-board monitor radio only
Insulate branch A9, black 12-pin plug casing,
branch A10, socket contact, white/brown cable,
and branch A15, socket contact, white/green
cable, on the basic wiring harness A and tie them
back on the standard wiring harness.
Branches A9, A10 and A15 are no longer
required.
"
20
A
3
A11
A6
A13
A12A8
A7
A9A10
A15
F 39 0978 B
A12 X322S
A13
X322B
A
F 39 0979 B
A6
4A7
F 39 0980 B
A
A9 A10
A15
F 39 0982 B

EN/18Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
9. To install the basic wiring harness A (E39 cars only)
0Cars with an on-board monitor radio only
Disconnect the black 12-pin plug casing X13598
from the on-board monitor radio connection plug
(20) and tie it back.
Connect branch A9, black 12-pin plug casing, into
the cleared slot (21) in the on-board monitor radio
connection plug (20).
If the car does not have a black 12-pin plug
casing X13598, branch A9 must be
connected direct.
"
0
This step only applies to cars without an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10 of
the 8-pin plug casing X18126.3
Connect branch A10, socket contact, white/brown
cable, to the free slot in the on-board monitor radio
connection plug (20) PIN10 on the 8-pin plug
casing X18126.
0
This step only applies to cars with an
existing mute cable on the on-board
monitor radio connection plug (20) PIN10
of the 8-pin plug casing X18126.3
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the on-board monitor radio connection plug (20).
Cut off the basic wiring harness A near branch
A10.
Connect branch A10, socket contact, white/brown
cable, to the supply cable of the on-board monitor
radio connection plug (20) PIN10, white/brown
cable, on the 8-pin plug casing X18126 using a
2-way insulation-piercing connector (1).
20
20 21 A9 X13598
F 39 0983 B
20
F 39 0985 B
A10
X18126/PIN10
20
20
F 39 0986 B
A10
211
20
X18126

EN/22Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0Cars without an on-board monitor radio only
Disconnect the black 12-pin plug casing X13598
from the radio connection plug (20) and tie it back.
Connect branch A2, black 12-pin plug casing, to
the cleared slot (21) in the radio connection plug
(20).
If the car does not have a black 12-pin plug
casing X13598, branch A2 must be
connected direct.
"
0
This step only applies to cars without an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
Connect branch A3, socket contact, white/brown
cable, to the free slot in the radio connection plug
(20) PIN10 on the 8-pin plug casing X18126.
0
This step only applies to cars with an
existing mute cable on the radio connection
plug (20) PIN10 of the 8-pin plug casing
X18126.
"
Carefully cut open the sheathing of the audio
wiring harness (21) for a length of 100 mm behind
the radio connection plug (20).
Cut off the basic wiring harness A near branch A3.
Connect branch A3, white/brown cable, to the
supply cable of the radio connection plug (20)
PIN10, white/brown cable, on the 8-pin plug
casing X18126 using a 2-way insulation-piercing
connector (1).
20 21
20
A2
A2 X13598
F 39 0973 B
20
F 39 0974 B
A3
X18126/PIN10
20
20
F 39 0975 B
A3
211
A
20 X18126

EN/24Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0
The figure shows the boot on the left."
Lay the basic wiring harness A, as shown in the
figure, with branches A6 to A13 and A15 along the
standard wiring harness and secure it with cable
ties (3).
0Lay branch A6, black 3-pin socket casing, and
branch A7, coaxial socket casing FME, to the
installation site of the compensator/telephone
aerial and connect them.
Screw the FME connector (4) to branch A7
(required if you are installing the bumper aerial).
Tie back any excess cable lengths.
"
0Connect branch A12, white 12-pin plug casing
on the basic wiring harness A to branch B1, white
12-pin socket casing on the power supply wiring
harness B.
Tie back plug connector A12 + B1 on the standard
wiring harness.
0Insulate branch A13, white 12-pin socket casing
and tie it back on the standard wiring harness (no
longer required).
F 39 0997 B
A7A63A12
A13A11
A10
A9
A8
A15
4
A6 A7
F 39 0998 B
A12A
B1B
F 39 0999 B
A13
F 39 1000 B

EN/25Retrofit/Installation kit No. 65 90 0 028 873 84 64 25,805 (others see cover sheet)
Installation Instructions no. 01 29 0 029 541 01 29 0 029 544 Issue date: 04.2001
10. To install the basic wiring harness A and power supply wiring harness B in E39/2 cars
0Carefully cut open the sheathing of the audio
wiring harness (20) for a length of 100 mm behind
the black plug connector X322.
Connect branch B2, open cable end, grey/red
cable, to the supply cable, grey/red cable, of the
black 12-pin plug connector X322 PIN5 using a
2-way insulation-piercing connector (1).
0Lay branch B3 and branch B4 on the power supply
wiring harness B along the standard wiring
harness (20) to the tied back black 2-pin plug
connector X325 above the power distributor in the
boot on the right.
Secure the power supply wiring harness B to the
standard wiring harness (20) using cable ties (3).
0Connect branch B3, black 2-pin socket casing
on the power supply wiring harness B to the black
2-pin plug casing X325S.
Connect branch B4, black 2-pin plug casing on
the power supply wiring harness B to the black
2-pin socket casing X325B.
0Tie back plug connectors X325S+B3 and
X325B+B4 on the standard wiring harness (20)
with cable ties.
When securing the connections, make sure
that the cable harnesses will not be damaged
during the subsequent assembly of the
car.
"
X3221
20
B2
120
F 39 1001 B
oooooooooooooooooo
B
320
20
B
B4B3
X325
F 39 1002 B
B
X325S
B4
B3
X325B
F 39 1003 B
20
X325S
B4 B3
X325B
F 39 1004 B