2000 VOLVO V70 Owners Manual

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_10a.htm[4/4/2013 10:25:18 PM]
A - CD changer mode selector
Press "CHGR" to actuate the CD changer mode. The disc/track last listened to will continue to play. If the CD-changer
cartridge* is empty, "---" will be displayed.
If a selected disc does not exist, the disc number and "5--" will be displayed and the next disc will be automatically
selected.
B - Disc number selector
Depress one of the preset buttons (1-6) to select the disc number desired. The selected disc number and track number
will be displayed.
C- Music search
Press the "
" or " " button to search within a track. While the button is depressed the playing time for this track
will be displayed.
*The functions pertaining to the CD-changer are only applicable if the unit has been connected to the Volvo CD-
changer, which is sold separately as an accessory, or on certain models, standard on the car.
If no CD-changer is connected to the unit "EEEE" will be displayed
if you happen to choose CHGR mode.
pg. 152 CD - Changer (option)
A - Changing the selected track number
Press "
" for forward selection or " " for bacKWard selection. The chosen disc number and track number will be
displayed.
B - Playing-time display
When the "CHGR" button is pressed the playing time for the current track is displayed for 5 seconds.
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_10a.htm[4/4/2013 10:25:18 PM]
C- Scan
Press this button to listen to the first ten seconds of each track. Press it again to stop scanning. During scanning
"SCAN" will be displayed.
pg. 153 CD - Changer (option)
A - Random choice
Press "RND" to actuate the random mode. From a disc chosen at random, 4 tracks will be played (also chosen at
random). A new disc will then be played in the same way. "RND" will be displayed when this function is engaged.
B - Pause
If you press the "volume" knob the disc is stopped, the unit is silent and "PAUSE" is displayed. To restart the disc
press the knob again.
C- To re-enter Radio mode
Push one of the waveband selector buttons.
D- To re-enter Tape mode
If a cassette is already inserted, the tape deck will re-engage if the "TAPE" button is pressed.
E- To re-enter CD changer mode
If the CD changer function has been disconnected, the CD changer mode can be re-entered by pressing the "CHGR"
button.
pg. 154 Technical specifications
SC-813
Radio
System: PLL (Phase Lock Loop) system with tuned RF (Radio
Frequency) front and end automatic wide band gain control.
Electronic suppression circuitry (noise killer).
This Radio is equipped with FM -Diversity.
Power output: 4 x 25 W (10% dist.)
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_10a.htm[4/4/2013 10:25:18 PM]
Output impedance:4 Ohms
System voltage:12 Volts, negative ground
Frequency range:
AM 530 -1710 kHz
FM 87.9 - 107.9 MHz
Sensitivity:
AM 1.1µV
FM 20µV
Stereo separation: 35 dB
Cassette deck
4track, 2 channel stereo
Full logic electronic tape transport Tape speed: 4.76 cm/sec.
Channel separation 53 dB
Frequency range 3015000 hz
S/N (120 µV) 56 dB without Dolby B NR
S/N (120 µV) 66 dB with Dolby B NR
Wow and Flutter < 0.06%
Pinch off
"Dolby" and the double D symbol
are the trademarks of Dolby Laboratories Licensing Corporation. Dolby noise
reduction manufactured under license from Dolby Laboratories Licensing Corporation.

Contents | Top of Page
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_11.htm[4/4/2013 10:25:25 PM]
2 0 0 0
VOLVO
S & V70
HomeLink® Universal Transceiver (option)
pg. 198 HomeLink® Universal Transceiver (option)
Indicator light
HomeLink® Universal Transceiver
This transceiver allows you to replace 3 hand -held transmitters with a single built-in device which can be installed in
your car on a sun visor or overhead console. This feature "learns" the radio frequency codes of most current
transmitters to operate garage doors, driveway gates, security lighting and home security systems. This transceiver is
powered by your car's electrical system.
NOTE: As a security precaution, the HomeLink® Universal Transceiver is designed to not function if the car has
been locked from the outside .
Programming the transceiver
1. Begin by erasing all 3 factory default channels by holding down the two outside buttons (buttons 1 and 3 in the
illustration above) on the HomeLink® Universal Transceiver until the indicator light on the transceiver begins to flash,
after approximately 20 seconds. Release the buttons.
2. Hold the end of your hand -held transmitter 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface, keeping the
indicator light in view. For placement questions, please contact HomeLink® at
1-800-355-3515 (Internet: www.HomeLink.jci.com
).
3. Using both hands, simultaneously push the hand -held transmitter button and the HomeLink® button to be
programmed. Do not release the buttons until this step has been completed.
The HomeLink® indicator light will begin to flash, first slowly, then rapidly. When the indicator light flashes rapidly
(indicating that the HomeLink® button has been successfully programmed), both buttons may be released.
The remaining two HomeLink® buttons can be programmed in the same way.
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_11.htm[4/4/2013 10:25:25 PM]
If, after several attempts, you do not successfully program the HomeLink® Universal Transceiver to learn the signal of
the hand -held transmitter, refer to the section "Programming rolling codes" or call the toll-free customer assistance
number: 1-800-355-3515 (Internet: www.HomeLink.jci.com
).
WARNING!
· If you use the HomeLink® Universal Transceiver to open a garage door or gate, be sure that no one is near the
gate or door while it is in motion.
· Do not use the HomeLink® Universal Transceiver with any garage door opener that lacks safety "stop" and
"reverse" features as required by federal safety standards. (This includes any garage door opener model
manufactured before April 1, 1982). A garage door opener which cannot "detect" an object, signalling the door to
"stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without these
features increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355-
3515 (Internet: www.HomeLink.jci.com
).
pg. 199 HomeLink® Universal Transceiver (option)
NOTE - Canadian residents:
During programming, your hand -held transmitter may automatically stop transmitting. To train your hand -held
transmitter, continue to hold the HomeLink® button (see steps 2, 3 under "Programming the transceiver") while you
press and repress ("cycle") your hand -held transmitter button every two seconds until the frequency signal has been
learned. The HomeLink® indicator light will flash slowly and then rapidly to indicate that the HomeLink® button has
been successfully programmed.
Programming rolling codes
Determine, in one of the following ways, if your garage door uses a rolling code system and is manufactured after
1996:
· Refer to the garage door opener's owner's manual for verification.
· The hand -held transmitter appears to program the HomeLink® Universal Transceiver but the transceiver does not
activate the garage door.
· Press the programmed HomeLink® button. The garage door opener has the rolling code feature if the HomeLink®
indicator light flashes rapidly and then glows steadily after approximately 2 seconds.
To train a garage door opener with the rolling code feature , follow these instructions after the transceiver has been
programmed (the aid of a second person may make the training quicker and easier):
1. Locate the training button on the garage door opener motor head unit . The exact location and color of the button
may vary. If you encounter difficulty, refer to the garage door opener owner's manual or call: 1-800-355-3515
(Internet: www.HomeLink.jci.com
).
2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.
3. Firmly press and release the programmed HomeLink® button. Press and release the HomeLink® button a second
time to complete the training process.
Some garage door openers may require you to do this procedure a third time to complete the training.
The programmed button on your HomeLink® Universal Transceiver
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_11.htm[4/4/2013 10:25:25 PM]
should now operate your garage door opener. The original hand -held transmitter can also be used, if necessary, to
operate the garage door.
The remaining two buttons can be programmed in the same way. In the event of any problems in programming the
HomeLink® Universal Transceiver, call 1-800-355-3515 (Internet: www.HomeLink.jci.com
).
Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used in place of hand -held transmitters.
To operate, press the programmed HomeLink® button to activate the garage door, driveway gate, security lighting,
home security system, etc.
The original hand -held transmitter can, of course, be used at any time.
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three programmed buttons:
1. Hold down the two outside buttons on the HomeLink® Universal Transceiver until the indicator light begins to
flash, after approximately 20 seconds.
2. Release both buttons.
The HomeLink® buttons can be reprogrammed using the procedures described on the previous page.
(HomeLink® information is continued on the next page)
pg. 200 HomeLink® Universal Transceiver (option)
Reprogramming a single HomeLink® button
1. Press and hold the desired HomeLink® button. Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after approximately 20 seconds), position the hand -held transmitter
2 to 5 in. (5 to 12 cm) away from the HomeLink® surface.
3. Press and hold the hand -held transmitter button.
The HomeLink® indicator light will begin to flash, first slowly then rapidly. When the indicator light flashes rapidly,
release both buttons.
The previously programmed device has now been erased and the new device can be activated by pressing the
HomeLink® button that has just been programmed. This procedure will not affect any other programmed HomeLink®
buttons.
NOTE:
· Retain the original transmitter(s) for future programming procedures (i.e., if you purchase a new car).
· It is also suggested that if you sell your car, the programmed channels on the HomeLink® Universal Transceiver be
erased for security purposes.

ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_11.htm[4/4/2013 10:25:25 PM]
Contents | Top of Page
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_12.htm[4/4/2013 10:25:31 PM]
2 0 0 0
VOLVO
S & V70
Index
pg. 201 Index
A
ABS 21
,23,83
Accessories - installing107
Adjustable steering wheel36
Adjusting headlights98
Air conditioning38,39,41
Air mix37
Air vents37
Airbag (SIPS)8
Airbag (SRS)4
Alarm47
All Wheel Drive (AWD)77,122
changing wheels95
snow chains89
towing81
wheel dimension caution88
Ambient temperature sensor29
Anti-lock Brake System (ABS)21,23,83
Antifreeze85,130
Ashtrays35
Audio systems
General information194
SC-813142
SC-816155
SC-900/901171
Automatic car washing115
Automatic daytime running28
Automatic transmission73,74,75,76,77,137
Kickdown74,76
Automatic transmission fluid134
Auxiliary seat12
Auxiliary socket35
ProCarManuals.com