2000 TOYOTA CAMRY oil change

W03086
F02267
1
2
F01195
Bolt
Adjusting
ValueSet Bolt
15'
30'Adjusting Bolt90105±15001 90105±15004 90105±15005 90105±15006
45'
1°00'
1°15'
1°30'121212121 Dot 2 Dots 3 Dots
± SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
SA±5
1956 Author: Date:
5. ADJUST CAMBER
NOTICE:
After the camber has been adjusted, inspect the toe±in.
(a) Remove the front wheels and speed sensor clamp.
(b) Remove the 2 nuts on the lower side of the shock absorb-
er.
(c) Coat the threads of the nuts with engine oil.
(d) Temporarily install the 2 nuts.
(e) Adjust the camber by pushing or pulling the lower side of
the shock absorber in the direction in which the camber
adjustment is required.
(f) Tighten the nuts.
Torque: 211 N´m (2,150 kgf´cm, 156 ft´lbf)
(g) Install the front wheels.
Torque: 103 N´m (1,050 kgf´cm, 76 ft´lbf)
(h) Check the camber.
HINT:

Try to adjust the camber to the center value.

Adjusting value for the set bolts is 6' ± 30' (0.1° ± 0.5°).
If the camber is not within the specification, using the table be-
low, estimate for how much additional camber adjustment will
be required, and select the camber adjusting bolt.
(i) Follow the above mentioned steps again. Between step
(b) and (c), exchange 1 or 2 selected bolts.
HINT:
When exchanging the 2 bolts, exchange 1 bolt for each time.

WARRANTY PARTS MARKING PROCEDURE ± PG006-03September 26, 2003
Page 3 of 3
NOTE:
The following parts do not have to be marked unless the technician can determine
failure and location.
air induction/ejection systems fuel injection systems
all computers fuel injectors
alternators fuel pump
audio (internal) ignition system
batteries internal engine components
bearings internal transmission components
belts oil cooler
catalytic converter power door lock switches
crankshaft remanufactured parts
cruise control starters
distributors suspension components
EGR systems valve covers
engine control systems window regulators
exchange parts wiper motors
exhaust systems
Parts
Marking
List
(Continued)

Toyota Supports ASE CertificationPage 1 of 1
SU001±00Title:
FRONT SUSPENSION SUPPORT NOISE
Models:
'97 ± '99 Avalon & '97 ± '00 Camry
Technical Service
BULLETIN
January 21, 2000

TSB Update Notice:
The information contained in this TSB updates SU002±99 dated September 3, 1999.
Revised text is red
and underlined.
To eliminate a noise occurrence from the front suspension on washboard type road
surfaces, the suspension support has been changed.
1997 ± 1999 Model Year Avalon and 1997 ± 2000
Camry vehicles.
The rubber bushing shape of the
suspension support has been changed.
MODELSTARTING VIN
Avalon4T1BF1*B*XU353593
JPP
Camry
JT2BF2*K*Y0237757
JT2BG2*K*Y0386559
NAP
Camry
4T1BF2*K*YU092142
4T1BF2*K*YU934448
4T1BG2*K*YU623567
4T1BG2*K*YU925151
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAMEQUANTITY
Avalon
48603±3302048603±33010Support Sub±Assembly,
Front Suspension RH1
48609±3312048609±33110Support Sub±Assembly,
Front Suspension LH1
Camry
48603±3302048603±33021Support Sub±Assembly,
Front Suspension RH1
48609±3312048609±33121Support Sub±Assembly,
Front Suspension LH1
OP CODECOMBODESCRIPTIONTIMEOPNT1T2
AR & R Suspension Support (RH and LH)
431451BAdjust Toe±In2.148603±330209199
CAdjust Camber
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
SUSPENSION
Introduction
Applicable
Vehicles
Production
Change
Information
Suspension
Support
Coil Spring
Strut
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 1
SU002±99Title:
FRONT SUSPENSION SUPPORT NOISE
Models:
'97 ± '99 Avalon & Camry
Technical Service
BULLETIN
September 3, 1999

To eliminate a noise occurrence from the front suspension on washboard type road
surfaces, the suspension support has been changed.
1997 ± 1999 Model Year Avalon and Camry vehicles
The rubber bushing shape of the
suspension support has been changed.
PREVIOUS PART
NUMBERCURRENT PART NUMBERPART NAMEQUANTITY
48603±3302048603±33010Support Sub±Assembly,
Front Suspension RH1
48609±3312048609±33110Support Sub±Assembly,
Front Suspension LH1
OP CODEGROUPDESCRIPTIONTIMEOPNT1T2
AR & R Suspension Support
(RH and LH)
431451BAdjust Toe±In2.148603±330209199
CAdjust Camber
Applicable Warranty*:
This repair is covered under the Toyota Basic Warranty. This warranty is in effect for
36 months or 36,000 miles, whichever occurs first, from the vehicle's in±service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
SUSPENSION
Introduction
Applicable
Vehicles
Modification
Information
Suspension Support
Coil spring
Strut
Parts
Information
Warranty
Information

Toyota Supports ASE CertificationPage 1 of 3
EG008-04Title:
M.I.L. ON" 1MZ-FE ENGINE MISFIRE
DTC P0300, P0301, P0302, P0303,
P0304, P0305 OR P0306
Models:
Applicable Avalon, Camry, Sienna & Solara
Technical Service
BULLETIN
April 28, 2004

Some vehicles equipped with 1MZ±FE (V6) engines without VVTi may exhibit a rough
idle and/or a M.I.L. ªONº condition with a diagnostic trouble code or codes for misfire
caused by an improperly operating ignition coil assembly. Production changes have been
implemented to prevent this condition from occuring.
2001 model year Japan built Camry vehicles equipped with 1MZ±FE engines (V6).
1998±2001 model year North American built Camry vehicles equipped with
1MZ±FE engines (V6)
1998 ± 1999 model year Avalon vehicles.
1998 ± 2000 model year Sienna vehicles.
1999 ± 2002 model year Solara vehicles equipped with 1MZ±FE engines produced
BEFORE the Production Change Effective VIN shown below.
MODELENGINEPRODUCTION CHANGE EFFECTIVE VIN
Solara1MZ±FE2T1CF2#P*2C578710
OP CODEMODELDESCRIPTIONTIMEOFPT1T2
191011AvalonR & R Ignition Coil (one coil)0.290080±190120273
191011
Camry
SolaraR & R Ignition Coil (one coil)0390080 190120273191011Solara
SiennaR & R Ignition Coil (one coil)0.390080±190120273
Applicable Warranty*:
This repair is covered under the Toyota Federal Emissions Warranty. This warranty is
in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle's
in-service date.
For California specification vehicles registered and operated in California, Maine,
Massachusetts or Vermont, this repair is covered under the California Emissions
Warranty, which is in effect for 36 months or 50,000 miles, whichever occurs first, from
the vehicle's in-service date.
* Warranty application is limited to correction of a problem based upon a customer's specific complaint.
ENGINE
Introduction
Applicable
Vehicles
Production
Change
Information
Warranty
Information

M.I.L. ªONº 1MZ±FE ENGINE MISFIRE DTC P0300 ± P0306 ± EG008-04April 28, 2004
Page 2 of 3
PREVIOUS PART NUMBERCURRENT PART NUMBERPART NAMEQTY
90080±19012SameIgnition Coil Assembly1
SPECIAL SERVICE TOOLS (SSTs)PART NUMBERQUANTITY
Toyota Diagnostic Tester Kit*
010012711
12 Megabyte Diagnostic Tester Program Card
with version 10.2a Software (or later)*01002593-0051
* Essential SSTs.
NOTE:
Additional Diagnostic Tester Kits, Program Cards or other SSTs may be ordered by
calling SPX/OTC at 1-800-933-8335.
TOOLS & MATERIALQUANTITY
Digital Volt Ohmmeter (DVOM)1
1. Confirm if vehicle is currently misfiring, running rough or hesitating.
If YES ± Go to Step 2.
If NO ± Review Freeze Frame Data and attempt to operate vehicle under similar
driving conditions ± see notes below for information that makes it more likely to
duplicate misfire.
NOTE:
The following activities will turn off misfire detection:
Changing engine RPM greater than 150 RPM.
Changing throttle position quickly.
Misfire duplication can be duplicated most readily when the engine speed and throttle
angle are held nearly constant for at least 2 minutes.
A
IGNITION 41
CYL #1 0%
CYL #2 0%
CYL #3 0%
CYL #4 Above 50%
CYL #5 0%
CYL #6 0%
MISFIRE RPM 0rpm
MISFIRE LOAD 0.00g/rev
# CODES 1
CHECK MODE OFF
MISFIRE TEST COMPL
B
IGNITION 205
CYL #1 0%
CYL #2 0%
CYL #3 0%
CYL #4 Above 50%
CYL #5 0%
CYL #6 0%
MISFIRE RPM 0rpm
MISFIRE LOAD 0.00g/rev
# CODES 1
CHECK MODE OFF
MISFIRE TEST COMPL
NOTE:
When misfire monitor is active, ignition value will change on Data List.
When pending misfire DTC is set, ªMISFIRE RPMº and ªMISFIRE LOADº will show values.
Values Will Change
From Zero
Parts
Information
Required
SSTs
Required
Tools &
Material
Repair
Procedure