2000 SUZUKI SWIFT window

9-2 BODY SERVICE
ANTI-CORROSION TREATMENT ............... 9-50
SEALANT APPLICATION AREAS................ 9-51
UNDER COATING APPLICATION AREAS .. 9-58
ANTI-CORROSION COMPOUND
APPLICATION AREA ................................... 9-60REQUIRED SERVICE MATERIAL ................... 9-61

GLASS, WINDOWS AND MIRRORS
FRONT DOOR GLASS
1. Door glass 6. Door sash 11. Glass bottom channel
2. Window regulator assembly
: Apply lithium grease 99000-25010 to sliding part.7. Front door grip 12. Glass bottom rubber
3. Glass run 8. Window regulator handle 13. Front door outer weather-strip
4. Door trim 9. Bottom channel attaching screw [A] Without power window model
5. Door sealing cover 10. Door opening weather-strip [B] With power window model

BODY SERVICE 9-3
REMOVAL
1) Remove window regulator handle (1) (if equipped).
For its removal, pull off snap by using a cloth (2) as shown in
figure.
2) Remove inside handle bezel (1).
3) Remove inside door grip.
4) Remove mirror inner garnish.
5) Remove door trim (1).
With inside handle bezel (2) tilted as shown in figure, turn
door trim (1) 90° counterclockwise to remove it.
And disconnect power window switch lead wire at coupler (if
equipped).
6) Remove door sealing cover (1).
7) Remove door mirror.
Refer to “DOOR MIRROR” in this section.
1

9-4 BODY SERVICE
8) Remove outer weather-strip (1).
Lower window all the way down. Then, use a tape-wrapped
putty knife to pry off outer weather-strip.
9) Remove bottom channel attaching screws (1).
10) When removing door glass (2), turn door glass 90° counter-
clockwise to remove it.
INSTALLATION
Reverse removal procedure to install door glass noting the follow-
ing instructions.
If there is deformity for glass run, replace new one.
Tighten bottom channel attaching screws. Tighten rear
screw first, and then tighten front screw.
Glass fitted position of bottom channel (1) is as shown in fig-
ure.
Glass fitted position of bottom channel “a”
3-door model : 335.5 - 338.5 mm (13.21 - 13.33 in.)
5-door model : 90.8 - 93.8 mm (3.57 - 3.69 in.) NOTE:
When removed outer weather-strip (1) from door panel
(2), be careful not to deformation for outer weather-strip
(1).
12
2
2
1

BODY SERVICE 9-5
Adjust equalizer (1) of window regular so that measurement
“a” and “b” are equal.
Secure door sealing cover (1) with adhesive (2).
Install door window regulator handle (1) so that it has a 45°
±12.5° angle when glass is fully closed as shown in figure
1 “a”“b”
1
2
A : Front

9-6 BODY SERVICE
FRONT DOOR WINDOW REGULATOR
REMOVAL
1) Remove door glass referring to “FRONT DOOR GLASS” in
this section.
2) Disconnect power window motor lead wire at coupler and
loosen clamp, if equipped.
3) Loosen regulator mounting screws (1) and take out regulator
through hole (2) as shown in figure.
INSPECTION
Check the following parts :
Check regulator sliding and rotating parts for greasing (1).
Check rollers (2) for wear and damage.
INSTALLATION
Reverse removal procedure to install window regulator noting the
following instruction.
When installing glass, check that the top part of the glass
contacts the glass run evenly and that the glass moves up
and down smoothly.
If the glass is tilted with respect to the glass run, adjust
equalizer (1) of window regulator so that measurement “a”
and “b” are equal.
1
12
1 “a”“b”

9-8 BODY SERVICE
REAR DOOR GLASS (IF EQUIPPED)
1. Door glass 7. Window regulator handle 13. Glass bottom rubber
2. Window regulator assembly
: Apply lithium grease 99000-25010 to moving section.8. Rear door outer weather-strip 14. Door inside pull handle case
3. Glass run 9. Rear door inside pull handle bracket [A] : Without power window model
4. Door trim 10. Rear door inner garnish [B] : With power window model
5. Door sealing cover 11. Rear door outer garnish
6. Door sash 12. Glass bottom channel

BODY SERVICE 9-9
REMOVAL
1) Remove window regulator handle (1) (if equipped).
For its removal, pull off snap by using a cloth (2) as shown in
figure.
2) Remove inside handle bezel (1).
3) Remove door inside pull handle case fitting screw.
4) Remove rear door inner garnish.
5) Remove door trim (1).
With inside handle bezel (2) tilted as shown in figure, turn
door trim 90° counterclockwise to remove it.
And disconnect power window switch lead wire at coupler (if
equipped).
6) Remove door inside pull handle bracket.
7) Remove door sealing cover (1).
2
1
1

9-10 BODY SERVICE
8) Remove rear door outer garnish (1).
9) Remove outer weather-strip (2).
Lower window all the way down. Then, use a tape-wrapped
putty knife (or screwdriver) to pry off outer weather-strip.
10) Detach rear part of glass run (1) from sash (2) and remove
sash (2) by removing 2 screws (3).
11) Loosen window regulator mounting screws (5).
12) When removing door glass (4), turn door glass 90° counter-
clockwise to remove it.
INSTALLATION
Reverse removal procedure to install door glass noting the follow-
ing instructions.
If there is deformity for glass run, replace new one.
Tighten bottom channel attaching screws. Tighten rear
screw first, and then tighten front screw.
Glass fitted position of bottom channel (1) is as shown in fig-
ure.
Glass fitted position of bottom channel
“a” : 201.9 - 204.9 mm (7.95 - 8.07 in.)
Secure door sealing cover (1) with adhesive (2). NOTE:
When removed outer weather-strip (2) from door panel
(3), be careful not to deformation for outer weather-strip
(2).
2 3
1
4
1
23
5
4
1
2