2000 SUZUKI SWIFT service indicator

6
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-1
GENERAL INFORMATION6- 3 . . . . . . . . . . . . . .
Statement on Cleanliness and Care 6- 3. . . . .
General Information on Engine Service 6- 3. .
Precaution on Fuel System Service 6- 4. . . . .
Fuel Pressure Relief Procedure 6- 5. . . . . . . .
Fuel Leakage Check Procedure 6- 5. . . . . . . .
ENGINE DIAGNOSIS6- 6 . . . . . . . . . . . . . . . . . . . General Description 6- 6. . . . . . . . . . . . . . . . . . .
On-Board Diagnostic System 6- 6. . . . . . . . . .
Precaution in Diagnosing Trouble 6- 9. . . . . . .
Engine Diagnostic Flow Table 6-10. . . . . . . . . .
Customer Problem Inspection From 6-12. . . . .
Malfunction Indicator Lamp Check 6-13. . . . . .
Diagnostic Trouble Code Check 6-13. . . . . . . .
SECTION 6
ENGINE GENERAL INFORMATION
AND DIAGNOSIS
(TBI FOR G10)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI for G10)6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI for G13)6-1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE MECHANICAL (G10)6A-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE MECHANICAL (G13 1 cam 16 valves)6A1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE COOLING6B-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE FUEL6C-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE AND EMISSION CONTROL SYSTEM (TBI for G10)6E1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE AND EMISSION CONTROL SYSTEM (SFI for G13)6E2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM (G10 ENGINE)6F-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM (G13 ENGINE)6F1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRANKING SYSTEM6G-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHARGING SYSTEM6H-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST SYSTEM6K-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE:
For the descriptions for vehicle without warm up three way catalytic converter (WUTWC), refer to Section
6 and 6E1 of the Service Manual mentioned in the FOREWORD of this manual.
CONTENTS

6-40 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
“IG COIL METER”Main relay
Ignition switch
In fuseMalfunction indicator lamp in combination meter
TABLE A-1 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP DOES
NOT COME “ON” AT IGNITION SWITCH ON (BUT ENGINE AT STOP)
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, ECM (PCM) causes the main relay to turn ON (close the contact point).
Then, ECM (PCM) being supplied with the main power, turns ON the malfunction indicator lamp (MIL). When the
engine starts to run and no malfunction is detected in the system, MIL goes OFF but if a malfunction was or is de-
tected, MIL remains ON even when the engine is running.
INSPECTION
STEPACTIONYESNO
1MIL Power Supply Check
1) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter comes ON?Go to Step 2.“IG COIL METER” fuse blown,
main fuse blown, ignition
switch malfunction, “B/W”
circuit between “IG COIL
METER” fuse and
combination meter or poor
coupler connection at
combination meter.
2ECM (PCM) Power and Ground Circuit
Check
Does engine start?Go to Step 3.Go to TABLE A-3 ECM (PCM)
POWER AND GROUND
CIRCUIT CHECK.
If engine is not cranked, go to
DIAGNOSIS in SECTION 8A.
3MIL Circuit Check
1) Turn ignition switch OFF and disconnect
connectors from ECM (PCM).
2) Check for proper connection to ECM
(PCM) at terminal C02-17.
3) If OK, then using service wire, ground
terminal C02-17 in connector
disconnected.
Does MIL turn on at ignition switch ON?Substitute a known-
good ECM (PCM) and
recheck.Bulb burned out or “V/Y” wire
circuit open.

6-1
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-1
GENERAL INFORMATION6-1- 3 . . . . . . . . . . . . . .
ENGINE DIAGNOSIS6-1- 6 . . . . . . . . . . . . . . . . . . .
General Description 6-1- 6. . . . . . . . . . . . . . . . . . .
On-Board Diagnostic System 6-1- 6. . . . . . . . . .
Precaution in Diagnosing Trouble 6-1- 9. . . . . . .
Engine Diagnostic Flow Table 6-1-10. . . . . . . . . .
Customer Problem Inspection From 6-1-12. . .
Malfunction Indicator Lamp Check 6-1-13. . . .
Diagnostic Trouble Code Check 6-1-13. . . . . .
Diagnostic Trouble Code Clearance 6-1-14. . .
Diagnostic Trouble Code Table 6-1-15. . . . . . .
Fail-safe Table 6-1-18. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 6-1-19. . . . . . . . . . . . . . . . . . .
Engine Basic Inspection 6-1-20. . . . . . . . . . . . .
Engine Diagnosis Table 6-1-22. . . . . . . . . . . . .
Scan Tool Data 6-1-29. . . . . . . . . . . . . . . . . . . . . . .
Inspection of ECM (PCM) and Its
Circuits 6-1-33. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage Check 6-1-33. . . . . . . . . . . . . . . . . . . . .
Resistance Check 6-1-37. . . . . . . . . . . . . . . . . .
Component Location 6-1-38. . . . . . . . . . . . . . . . . .
Table A-1 MIL Circuit Check
(Lamp does not come on) 6-1-39. . . . . . . . . . . . Table A-2 MIL Circuit Check
(Lamp remains ON) 6-1-40. . . . . . . . . . . . . . . . . .
Table A-3 ECM (PCM) Power and
Ground Circuit Check 6-1-41. . . . . . . . . . . . . . . .
DTC P0105 MAP Circuit Malfunction 6-1-43. . . .
DTC P0110 IAT Circuit Malfunction 6-1-46. . . . .
DTC P0115 ECT Circuit Malfunction 6-1-48. . . .
DTC P0120 Throttle Position Circuit
Malfunction 6-1-50. . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0121 Throttle Position Circuit
Range / Performance Problem 6-1-52. . . . . . . . .
DTC P0130 HO2S Circuit Malfunction
(Sensor-1) 6-1-54. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0133 HO2S Circuit Slow
Response (Sensor-1) 6-1-56. . . . . . . . . . . . . . . .
DTC P0134 HO2S Circuit No Activity
Detected 6-1-57. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0135 HO2S Heater Circuit
Malfunction (Sensor-1) 6-1-58. . . . . . . . . . . . . . .
DTC P0136 HO2S Circuit Malfunction
(Sensor-2) 6-1-60. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0141 HO2S Heater Circuit
Malfunction (Sensor-2) 6-1-63. . . . . . . . . . . . . . .
DTC P0171 Fuel System Too Lean 6-1-65. . . . .
DTC P0172 Fuel System Too Rich 6-1-65. . . . . .
SECTION 6-1
ENGINE GENERAL INFORMATION
AND DIAGNOSIS
(SFI FOR G13)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

Main
fuseIgnition
switch
Main
relay Malfunction indicator lamp in combination meter
Relay
box Fuse box
C01-1
C01-2
C01-3
ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-39
TABLE A-1 MALFUNCTION INDICATOR LAMP CIRCUIT CHECK – LAMP DOES
NOT COME “ON” AT IGNITION SWITCH ON (BUT ENGINE AT STOP)
CIRCUIT DESCRIPTION
When the ignition switch is turned ON, ECM (PCM) causes the main relay to turn ON (close the contact point).
Then, ECM (PCM) being supplied with the main power, turns ON the malfunction indicator lamp (MIL). When the
engine starts to run and no malfunction is detected in the system, MIL goes OFF but if a malfunction was or is de-
tected, MIL remains ON even when the engine is running.
INSPECTION
STEPACTIONYESNO
1MIL Power Supply Check
1) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter comes ON?Go to Step 2.“IG” fuse blown, main
fuse blown, ignition switch
malfunction, “B/W” circuit
between “IG” fuse and
combination meter or poor
coupler connection at
combination meter.
2ECM (PCM) Power and Ground Circuit
Check Does engine start?Go to Step 3.Go to TABLE A-3 ECM (PCM)
POWER AND GROUND
CIRCUIT CHECK.
If engine is not cranked, go to
DIAGNOSIS in SECTION 6G.
3MIL Circuit Check
1) Turn ignition switch OFF and disconnect
connectors from ECM (PCM).
2) Check for proper connection to ECM
(PCM) at terminal C03-1.
3) If OK, then using service wire, ground
terminal C03-1 in connector
disconnected.
Does MIL turn on at ignition switch ON?Substitute a
known-good ECM
(PCM) and recheck.Bulb burned out or “V” wire
circuit open.

6E1-8 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
ON-VEHICLE SERVICE
GENERAL
When the hoses have been disconnected and system’s component
removed for service, be sure to reinstall component properly, and
route and connect hoses correctly after service. Refer to Emission
Control Information Label for proper connection of hoses (if
equipped).
ACCELERATOR CABLE ADJUSTMENT
1) Confirm that ambient temperature is higher than 0C, 32F.
2) Warm up engine to normal operating temperature with all elec-
tric loads OFF and stop engine.
3) Confirm that clearance “c” between throttle lever (1) and stop
screw (2) is less than about 1 mm (0.04 in.).
4) Check accelerator cable for play.
Accelerator cable play “a”: 10 – 15 mm (0.4 – 0.6 in.)
Cable play should be within specification. If out of specification,
loosen accelerator cable lock nut and adjust by turning adjusting
nut (3). Be sure to tighten lock nut (4) securely after adjustment.
5) With accelerator pedal depressed fully, check clearance be-
tween throttle lever and lever stopper (5) (throttle body) which
should be within following specification.
Clearance “b”: 0.5 – 2.0 mm (0.02 – 0.07 in.)
(With pedal depressed fully)
If measured value is out of specification, adjust it to specification
by changing height of pedal stopper bolt (6).
IDLE SPEED INSPECTION
Before inspecting idle speed, make sure to the following.

Lead wires and hoses of Electronic Fuel Injection and engine
emission control systems are connected securely.

After warming up engine, accelerator cable has some play, that
is, it is not tight.

Ignition timing is within specification.

All of electrical loads except ignition are switched off.

Air cleaner has been properly installed and is in good condition.

Malfunction indicator lamp does not light when engine running.
After above items are all confirmed, check idle speed as follows.

7B
AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-1
GENERAL DESCRIPTION7B- 3 . . . . . . . . . . . . . .
Electronic Shift Control System 7B- 5. . . . . . . . .
DIAGNOSIS7B-11 . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-board diagnostic system 7B-11. . . . . . . . . . .
Precaution in Diagnosing Trouble 7B-12. . . . . . .
Automatic Transmission Diagnostic
Flow Table 7B-13. . . . . . . . . . . . . . . . . . . . . . . . . .
Customer problem inspection form
(example) 7B-15. . . . . . . . . . . . . . . . . . . . . . . .
Malfunction indicator lamp (MIL)
check 7B-16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code(s) check 7B-16. . . . .
Diagnostic trouble code(s)
clearance 7B-16. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code (DTC) table 7B-17. . .
Fail-safe table 7B-17. . . . . . . . . . . . . . . . . . . . . .
Visual inspection 7B-18. . . . . . . . . . . . . . . . . . .
Automatic Transmission Basic Check 7B-19. . .
Symptom-to-Inspection Table 7B-20. . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B-21. . . . DTC P0720 Output Speed Sensor
(A / T VSS) Circuit Malfunction 7B-24. . . . . . . . .
DTC P0753 Shift Solenoid-A (No.1)
Electrical 7B-26. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0758 Shift Solenoid-B (No.2)
Electrical 7B-26. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0751 Shift Solenoid-A (No.1)
Performance or Stuck Off 7B-28. . . . . . . . . . . . .
DTC P0756 Shift Solenoid-B (No.2)
Performance or Stuck Off 7B-28. . . . . . . . . . . . .
Table A-1 No Starting or Slipping in Any
Drive Range 7B-30. . . . . . . . . . . . . . . . . . . . . . . .
Table A-2 Gear Change Failure 7B-31. . . . . . . . .
Table A-3 Excessive Shock at Range
Selection or Gear Change 7B-31. . . . . . . . . . . .
Stall test 7B-32. . . . . . . . . . . . . . . . . . . . . . . . . . .
Line pressure test 7B-33. . . . . . . . . . . . . . . . . .
Road test 7B-35. . . . . . . . . . . . . . . . . . . . . . . . . .
Manual road test 7B-36. . . . . . . . . . . . . . . . . . .
Engine brake test 7B-36. . . . . . . . . . . . . . . . . . .
“P” range test 7B-37. . . . . . . . . . . . . . . . . . . . . .
Shift solenoid valve check 7B-37. . . . . . . . . . .
SECTION 7B
AUTOMATIC TRANSMISSION (3 A/T)
(VEHICLE WITH WU-TWC)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
For the descriptions (items) not found in this section, refer to the same section of the Service Manual men-
tioned in the FOREWORD of this manual.
CONTENTS

8G
IMMOBILIZER CONTROL SYSTEM 8G-1
GENERAL DESCRIPTION8G- 2 . . . . . . . . . . . . . .
On-Board Diagnostic System
(Self-Diagnosis Function) 8G- 4. . . . . . . . . . . . .
DIAGNOSIS8G- 6 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions in Diagnosing
Troubles 8G- 6. . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSTIC FLOW TABLE 8G- 8. . . . . . . . . . . . .
Diagnostic Trouble Code Check
(Immobilizer Control Module) 8G-10. . . . . . . . .
Diagnostic Trouble Code Check (ECM) 8G-10. .
Diagnostic Trouble Code Table 8G-12. . . . . . . . .
A-1 Code (DTC) is not Outputted
from Diagnostic Output Terminal
of Immobilizer Diagnostic Coupler 8G-13. . . . . A-2 Immobilizer Indicator Lamp Check
(Immobilizer Indicator Lamp does not
Light at Ignition Switch ON) 8G-14. . . . . . . . . . .
A-3 Immobilizer Indicator Lamp Check
(Immobilizer Indicator Lamp Remains
ON after Engine Starts) 8G-15. . . . . . . . . . . . . .
HOW TO REGISTER IGNITION KEY8G-16 . . . . .
PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT8G-17 . .
PROCEDURE AFTER ECM
REPLACEMENT8G-18 . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS8G-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 8G
IMMOBILIZER CONTROL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:

Whether the immobilizer indicator lamp is used in the particular vehicle or not depends on specifica-
tions. If there is a monitor coupler in the engine room near the left strut assembly, the vehicle is not
equipped with immobilizer indicator lamp and if there isn’t, it is equipped with immobilizer indicator
lamp.

For the descriptions (items) not found in this section, refer to the section 8G of the Service Manual men-
tioned in FOREWORD of this manual.
CONTENTS

8G-8 IMMOBILIZER CONTROL SYSTEM
Fig. 1 for Step 1 Fig. 2 for Step 1 Fig. 3 for Step 2
1. Monitor coupler
2. Service wire
A: Diagnosis switch terminal
B: Ground terminal
Fig. 4 for Step 3
“CHECK ENGINE” light
0.5
ON
OFF
TIME (sec.)
DIAGNOSTIC FLOW TABLE

STEPACTIONYESNO
11) Make sure that diagnosis switch
terminal in monitor coupler is not
grounded by service wire. See Fig. 1.
2) Check malfunction indicator lamp
while ignition switch is ON (but without
starting engine). See Fig. 2.
Dose malfunction indicator lamp flash?Go to Step 3.
If malfunction indicator lamp
remains ON, go to Step 2.

If malfunction indicator lamp
remains OFF, go to
“MALFUNCTION INDICATOR
LAMP CHECK” in Section 6.
21) Using service wire, ground diagnosis
switch terminal in monitor coupler.
See Fig. 3.
Dose malfunction indicator lamp flash?Immobilizer control
system is in good
condition.Go to “MALFUNCTION
INDICATOR LAMP CHECK” in
Section 6.
3Dose malfunction indicator lamp flash as
Fig. 4?Go to Step 4.Go to “MALFUNCTION
INDICATOR LAMP CHECK” in
Section 6.
41) Check DTC stored in Immobilizer
Control Module referring to
“DIAGNOSTIC TROUBLE CODE
CHECK (IMMOBILIZER CONTROL
MODULE)” in this section.
Is there any DTC(s)?Go to flow table for
DTC No.Go to Step 5.
51) Check DTC stored in ECM referring to
“DIAGNOSTIC TROUBLE CODE
CHECK (ECM)” in this section.
Is there any DTC(s)?Go to flow table for
DTC No.Substitute a known-good ECM
and recheck.
NOTE:
After replacing with a known-
good ECM, register ECM /
Immobilizer Control Module
code in ECM by performing
procedure described in
“Procedure after ECM
Replacement” section.