2000 SUZUKI SWIFT service indicator

8G-10 IMMOBILIZER CONTROL SYSTEM
1. Immobilizer diagnostic coupler
EXAMPLE :
COIL ANTENNA FAILURE (CODE NO.13)
Voltmeter indicator

NORMAL (No code)
Voltmeter indicatorTIME (sec.)
TIME (sec.) CODE No. 13CODE No. 13CODE No. 13
High
Low
High
Low
1. Monitor coupler
2. Service wire
A: Diagnosis switch
terminal
B: Ground terminal
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
(IMMOBILIZER CONTROL MODULE)
1) Using analog type voltmeter, connect positive probe to diagnos-
tic output terminal and negative probe to ground of immobilizer
diagnostic coupler with ignition switch turned ON.
2) Read deflection of voltmeter indicator which represents DTC as
shown in example below and write it down. For details of DTC,
refer to Immobilizer Control Module side in “Diagnostic Trouble
Code Table”.
If voltmeter indicator dose not deflect, go to “Diagnostic Flow
Table A”.
NOTE:
If abnormality or malfunction lies in two or more areas, volt-
meter indicates applicable codes three times each.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK (ECM)
[Not using SUZUKI scan tool] (Vehicle equipped with
monitor coupler)
1) Using service wire, ground diagnostic switch terminal in monitor
coupler.
2) Read DTC from flashing pattern of malfunction indicator lamp as
shown in example below and write it down. For details of DTC,
refer to ECM side in “Diagnostic Trouble Code Table”.
If lamp remains ON, go to “Malfunction Indicator Lamp Check”
in Section 6.
NOTE:
If abnormality or malfunction lies in two or more areas, mal-
function indicator lamp indicates applicable codes three
times each.
And flashing of these codes is repeated as long as diagno-
sis terminal is grounded and ignition switch is held at ON
position.

IMMOBILIZER CONTROL SYSTEM 8G-11
EXAMPLE: When serial data link wire is defective (Code No.83)
ON
OFFMalfunction
indicator lamp
Code No.83 Code No.83 Code No.83
Time (sec.)
1. Data link connector (DLC)
3) After completing the check, turn ignition switch OFF and discon-
nect service wire from monitor coupler.
[Using SUZUKI scan tool] (Vehicle not equipped with
monitor coupler)
1) Turn ignition switch OFF.
2) After setting cartridge to Suzuki scan tool, connect it to data link
connector (DLC) located on underside of instrument panel at
driver’s seat side.
Special Tool
(A): 09931-76011 (Suzuki scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC adapter)
3) Turn ignition switch ON.
4) Read DTC stored in ECM according to instructions displayed on
Suzuki scan tool and print it or write it down. Refer to Suzuki scan
tool operator’s manual for further details.
NOTE:

When reading DTC stored in ECM using Suzuki scan tool,
select “ECM” from the applications menu and “SUZUKI
mode” from the communication mode menu displayed on
Suzuki scan tool.

If ECM detects a trouble in both electric fuel injection sys-
tem and immobilizer control system, Suzuki scan tool in-
dicates trouble codes of both systems using Suzuki mode
of ECM application.
If communication between Suzuki scan tool and ECM is not pos-
sible, check if Suzuki scan tool is communicable by connecting
it to ECM in another vehicle. If communication is possible in this
case, Suzuki scan tool is in good condition. Then check data link
connector and serial data line (circuit) in the vehicle with which
communication was not possible.
5) After completing the check, turn ignition switch OFF and discon-
nect Suzuki scan tool from data link connector (DLC).

8G-14 IMMOBILIZER CONTROL SYSTEM
1. Main fuse
2. Main relay
3. ECM
4. Immobilizer indicator lamp
(Vehicle not equipped with
monitor coupler)For G10 engine
For G13B engine
For G10 engine For G13B engine
A-2 IMMOBILIZER INDICATOR LAMP CHECK
(IMMOBILIZER INDICATOR LAMP DOSE NOT LIGHT AT IGNITION SWITCH ON)
STEPACTIONYESNO
11) Turn ignition switch ON.
Do other indicator / warning lights in
combination meter come ON?Go to Step 2.“IG” fuse blown, main fuse blown,
ignition switch malfunction,
“(d)” circuit between “IG” fuse
and combination meter or poor
coupler connection at
combination meter.
21) Turn ignition switch OFF and
disconnect connectors from ECM.
2) Check for proper connection to ECM
at terminal C02-18 for G10 engine or
C01-28 for G13B engine.
3) If OK, then using service wire, ground
terminal C02-18 for G10 engine or
C01-28 for G13B engine in connector
disconnected.
Does immobilizer indicator lamp turn on
at ignition switch ON?Substitute a known-
good ECM and
recheck.Bulb burned out or “(P)” wire
circuit open.