2000 SUZUKI SWIFT FLUID LEVEL CHECK

1. Full level mark (hole)
2. Low level mark (hole)
Oil pan capacity
Oil filter capacity
Others
Total1.0 L and 1.3 L Engine
About 3.1 liters
(6.5 / 5.5 US / lmp pt.)
About 0.2 liter
(0.4 / 0.3 US / lmp pt.)
About 0.3 liter
(0.6 / 0.5 US / lmp pt.)
About 3.6 liters
(7.5 / 6.3 US / lmp pt.)
0B-8 MAINTENANCE AND LUBRICATION
7) Replenish oil until oil level is brought to FULL level mark on dip-
stick (oil pan and oil filter capacity). Filler inlet is at the top of cyl-
inder head cover.
8) Start engine and run it for three minutes. Stop it and wait another
5 minutes before checking oil level. Add oil, as necessary, to
bring oil level to FULL level mark on dipstick.
Engine Oil Capacity
NOTE:
Engine oil capacity is specified as left table.
However, note that amount of oil required when actually
changing oil may somewhat differ from data in left table de-
pending on various conditions (temperature, viscosity, etc.).
9) Check oil filter and drain plug for oil leakage.
ITEM 1-5
Engine Coolant Change
WARNING:
To help avoid danger of being burned, do not remove radia-
tor cap while engine and radiator are still hot. Scalding fluid
and steam can be blown out under pressure if cap is taken
off too soon.
CAUTION:
When changing engine coolant, use mixture of 50% water
and 50% ethylene-glycol base coolant (Anti-Freeze/Anti-
corrosion coolant) for the market where ambient tempera-
ture falls lower than –16C (3F) in winter and mixture of
70% water and 30% ethylene-glycol base coolant for the
market where ambient temperature doesn’t fall lower than
–16C (3F).
Even in a market where no freezing temperature is antici-
pated, mixture of 70% water and 30% ethylene-glycol base
coolant should be used for the purpose of corrosion protec-
tion and lubrication.
Refer to SECTION 6B for COOLANT CAPACITY.

1. Ball joint stud dust seal (boot)
2. Suspension arm
1. Tie-rod end boot
2. Steering gear case boot
3. Universal joint
0B-16 MAINTENANCE AND LUBRICATION

Check front and rear suspension systems for damaged, loose or
missing parts; also for parts showing signs of wear or lack of lu-
brication.
Repair or replace defective parts, if any.

Check front suspension arm ball joint stud dust seals for leakage,
detachment, tear or any other damage.
Replace defective boot, if any.
ITEM 6-5
Steering System Inspection
1) Check steering wheel for play and rattle, holding vehicle straight
on ground.
Steering wheel play “a”: 0 – 30 mm (0 – 1.1 in.)
2) Check steering linkage for looseness and damage. Repair or re-
place defective parts, if any.
3) Check boots of steering linkage and steering gear case for dam-
age (leaks, detachment, tear, etc.). If damage is found, replace
defective boot with new one.
4) Check universal joints of steering shaft for rattle and damage. If
rattle or damage is found, replace defective part with a new one.
ITEM 6-6
Power Steering (P / S) System Inspection (if equipped)
1) Visually check power steering system for fluid leakage and hose
for damage and deterioration.
Repair or replace defective parts, if any.
2) With engine stopped, check fluid level indicated on fluid tank,
which should be between MAX and MIN marks. If it is lower than
MIN, fill fluid up to MAX mark.
NOTE

Be sure to use specified P / S fluid.

Fluid level should be checked when fluid is cool.
3) Visually check pump drive belt for cracks and wear.
4) Check belt for tension, referring to item 1-1 in this section.
If necessary, adjust or replace.

1. Oil level gauge
2. FULL HOT mark
3. LOW HOT mark
4. FULL COLD mark
5. LOW COLD mark
1. Drain plug
0B-18 MAINTENANCE AND LUBRICATION
ITEM 6-9
Automatic Transmission
[Fluid level inspection]
1) Inspect transmission case for evidence of fluid leakage.
Repair leaky point, if any.
2) Make sure that vehicle is placed level for fluid level check.
3) Check fluid level.
For fluid level checking procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B and be sure to perform it under specified
conditions. If fluid level is low, replenish specified fluid.
[Fluid change]
1) Perform steps 1) and 2) of above Fluid Level Inspection.
2) Change fluid. For its procedure, refer to ON-VEHICLE SER-
VICE in SECTION 7B.
CAUTION:
Use of specified fluid is absolutely necessary.
[Fluid cooler hose change]
Replace inlet and outlet hoses (1) of cooler hose and their clamps.
For replacement procedure, refer to ON-VEHICLE SERVICE in
SECTION 7B.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

Engine oil ––––– level, leakage

Engine coolant ––––– level, leakage

Fuel ––––– level, leakage

A / T fluid ––––– level, leakage

Air cleaner element ––––– dirt, clogging

Battery ––––– fluid level, corrosion of terminal

Water pump belt ––––– tension, damage

Throttle cable ––––– play, installation

Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend

Connectors of electric wire harness ––––– disconnection, friction

Fuses ––––– burning

Parts ––––– installation, bolt ––––– looseness

Parts ––––– deformation

Other parts that can be checked visually
Also check following items at engine start, if possible

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Fuel level meter

Tachometer, if equipped

Abnormal air being inhaled from air intake system

Exhaust system ––––– leakage of exhaust gas, noise

Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E1
Section 8
Section 6
Section 6H
Section 8 (section 6 for pressure check)
Section 8
Section 8

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

Engine oil ––––– level, leakage

Engine coolant ––––– level, leakage

Fuel ––––– level, leakage

A / T fluid ––––– level, leakage

Air cleaner element ––––– dirt, clogging

Battery ––––– fluid level, corrosion of terminal

Water pump belt ––––– tension, damage

Throttle cable ––––– play, installation

Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend

Connectors of electric wire harness ––––– disconnection, friction

Fuses ––––– burning

Parts ––––– installation, bolt ––––– looseness

Parts ––––– deformation

Other parts that can be checked visually
Also check following items at engine start, if possible

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Fuel level meter

Tachometer, if equipped

Abnormal air being inhaled from air intake system

Exhaust system ––––– leakage of exhaust gas, noise

Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E2
Section 8
Section 6
Section 6H
Section 8 (Section 6 for pressure check)
Section 8
Section 8

(a)
1
2
3
(a)
(a)
6
74
5
(a)
M/TM/T
9
(a)
4
7
(a)
8
1. Right mounting
2. Right mounting
bracket
3. Left mounting
4. Left mounting bracket
5. Left mounting bracket
stiffener6. Rear mounting
7. Rear mounting
bracket
8. Rear torque rod
9. Rear torque rod
bracket
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-67
INSTALLATION
1) Lift engine with transmission into engine compartment, but do
not remove support device.
2) Install engine right mounting to right mounting bracket and stiff-
ener.
3) Install engine left mounting to body.
4) Install rear mounting to body (For M/T model)
Install torque rod (For A/T model)
5) Tighten bolts and nuts of all parts installed in above steps 2),
3) and 4) or 5) to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
6) Remove support device.
7) Reverse removal procedures for installation of remainder.

Push in each drive shaft joint fully so that snap ring engages
with differential gear or center bearing support.
Use care not to damage oil seal lip when inserting.

Clamp electric wire securely.
8) Adjust clutch pedal free travel by referring to Section 7C. (M / T)
Adjust gear select cable and A / T throttle pressure control
cable, referring to Section 7B. (A / T)
9) Adjust gear shift control lever by referring to Section 7A. (M / T)
10) Adjust accelerator cable play by referring to Section 6E.
11) Refill transmission with gear oil. (A / T fluid for A / T model) by
referring to Section 0B.
12) Refill engine with engine oil by referring to Section 0B.
13) Refill cooling system by referring to Section 6B.
14) Adjust A / C compressor and / or P / S pump drive belt referring
to Section 0B. (if equipped)
15) Check P / S fluid level by referring to Section 3B1. (if equipped)
16) Upon completion of installation, verify that there is no fuel leak-
age, coolant leakage, transmission oil leakage or exhaust gas
leakage at each connection.

7B-18 AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC)
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

A / T fluid– – – – – level, leakage, color

A / T fluid hoses – – – – – disconnection, looseness, deterioration

Throttle cable – – – – – play, installation

A / T oil pressure control cable and select cable – – – – – installation

Engine oil – – – – – level, leakage

Engine coolant – – – – – level, leakage

Battery – – – – – fluid level, corrosion of terminal

Connectors of electric wire harness – – – – – disconnection, friction

Fuses – – – – – burning

Parts – – – – – installation, bolt – – – – – looseness

Parts – – – – – deformation

Other parts that can be checked visually
Also check following items at engine start, if possible.

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Other parts that can be checked visuallySection 0B
Section 7B
Section 6E1 or 6E2
Section 7B
Section 0B
Section 0B
Section 6 or 6-1
Section 8
Section 6 or 6-1
Section 6H
Section 8 (Section 6A or 6A1 for
pressure check)

AUTOMATIC TRANSMISSION (3 A / T) (VEHICLE WITH WU-TWC) 7B-19
Fig. 1 for Step 5. Fig. 2 for Step 5. Fig. 3 for Step 5.
When not using SUZUKI
scan tool:
lever position
Terminal
Selector
AUTOMATIC TRANSMISSION BASIC CHECK
This check is very important for troubleshooting when PCM (ECM) has detected no DTC and no abnormality has
been found in visual inspection. Follow the flow table carefully.
STEPACTIONYESNO
1Was “AUTOMATIC TRANSMISSION DIAG. FLOW TABLE”
performed?Go to Step 2.Go to
“AUTOMATIC
TRANSMISSION
DIAG. FLOW
TABLE”.
2Check A / T Fluid.
Warm transmission to normal operating temperature and check
fluid level and contamination referring to “FLUID LEVEL
CHECK” of “ON-VEHICLE SERVICE” in this section.
Is it in good condition?Go to Step 3.Add or change
fluid.
3Check Fluid Pressure Control Cable.
1) Warm up engine to normal operating temperature.
2) Check fluid pressure control cable for play referring to
“FLUID PRESSURE CONTROL CABLE” of “ON-VEHICLE
SERVICE” in this section.
Is it in good condition?Go to Step 4.Adjust.
4Check Select Cable for Adjustment referring to “SELECT
CABLE” of “ON-VEHICLE SERVICE” in this section.
Is it adjusted correctly?Go to Step 5.Adjust.
5Check Transmission Range Sensor (Switch) Circuit for
Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C03-3 C03-4 C03-5 C03-14
Go to Step 6.Go to Step 3 of
DTC P0705
Flow Table.
2) Check voltage at terminals C03-3, C03-4, C03-5, C03-14,
C03-15 and C03-16 for G10 engine model (C02-11, C02-12,
C02-14, C02-15, C02-21 and C02-23 for G13 engine
model) respectively with selector lever shifted to each
range. See Fig. 2.
Taking terminal C03-3 for G10 engine model (C02-11 for
G13 engine model) as an example, is battery voltage
indicated only when selector lever is shifted to “2” range and
0 V for other ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?
6Check Engine Idle speed referring to Section 6E1 or 6E2.
Is it in good condition?Go to
“SYMPTOM-TO-
INSPECTION
TABLE” below.Go to Section
6E1 or 6E2.
C03-5
(C02-21)C03-16
(C02-15)C03-4
(C02-12)C03-15
(C02-14)C03-3
(C02-11)C03-14
(C02-23)
PB + V0 V0 V0 V0 V0 V
R0 VB + V0 V0 V0 V0 V
N0 V0 VB + V0 V0 V0 V
D0 V0 V0 VB + V0 V0 V
20 V0 V0 V0 VB + V0 V
L0 V0 V0 V0 V0 VB + V