2000 SUZUKI SWIFT Valve adjustment

1. Thickness gauge IN
EX
0B-6 MAINTENANCE AND LUBRICATION
Water Pump Belt Replacement
Replace belt with a new one. Refer to SECTION 6B for replacement
procedure of pump belt.
NOTE:
When replacing belt with a new one, adjust belt tension to
5 – 7 mm (0.20 – 0.27 in.).
ITEM 1-2
Camshaft Timing Belt Replacement
Replace belt with new one. Refer to SECTION 6A or 6A1 for re-
placement procedure.
CAUTION:

Do not bend or twist timing belt.

Do not allow timing belt to come into contact with oil, wa-
ter, etc.
ITEM 1-3
Valve Lash Inspection (1.3 liter engine only)
1) Remove cylinder head cover.
2) Inspect intake and exhaust valve lash and adjust as necessary.
Refer to SECTION 6A1 for valve lash inspection and adjustment
procedure.
Valve
lash
(gap)
When cold
(Coolant temperature is
15 – 25C or 59 – 77F)When hot
(Coolant temperature is
60 – 68C or
140 – 154F)
(gap)
specifi-
cation
Intake0.13 – 0.17 mm
(0.005 – 0.007 in.)0.17 – 0.21 mm
(0.007 – 0.008 in.)
cation
Exhaust0.23 – 0.27 mm
(0.009 – 0.011 in.)0.28 – 0.32 mm
(0.011 – 0.013 in.)
Special Tool
(A): 09917-18211
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 8.5 lb-ft)
3) Install cylinder head cover and tighten bolts to specification.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-25
ConditionPossible CauseReferring Item
Engine hesitates
(Momentary lack of
response as
accelerator is
depressed.
Can occur at all
vehicle speeds.
Usually most severe
when first trying to
make vehicle move,
as from a stop sign.)Ignition system out of order

Spark plug faulty or plug gap out of adjustment

Leaky high-tension cord
Fuel system out of order

Fuel pressure out of specification
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
Engine overheating
Low compression
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-3
EGR system in section 6E2
TP sensor, ECT sensor or MAP
sensor in Section 6E2
Diagnostic Flow Table B-1
Refer to “Overheating” section
Previously outlined
Surge
(Engine power
variation under
steady throttle or
cruise.
Feels like vehicle
speeds up and down
with no change in
accelerator pedal.)Ignition system out of order

Leaky or loosely connected high-tension cord

Faulty spark plug (excess carbon deposits,
improper gap, and burned electrodes, etc.)
Fuel system out of order

Variable fuel pressure
–Kinky or damaged fuel hose and lines
–Faulty fuel pump (clogged fuel filter)
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
High-tension cords in Section 6F1
Spark plugs in Section 6F1
Diagnostic Flow Table B-3
EGR system in Section 6E2
MAP sensor in Section 6E2
Diagnostic Flow Table B-1
Excessive
detonation
(Engine makes
continuously
sharp metallic
knocks that change
with throttle opening.
Sounds like pop corn
popping.)Engine overheating
Ignition system out of order

Faulty spark plug

Loose connection of high-tension cord
Fuel system out of order

Clogged fuel filter (faulty fuel pump) or fuel lines

Air inhaling from intake manifold or throttle body
gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of ECT sensor or MAP sensor

Faulty fuel injector(s).

Faulty ECM (PCM)

Excessive combustion chamber depositsRefer to “Overheating” section
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-1 or B-2
EGR system in Section 6E2
ECT sensor or MAP sensor in
Section 6E2
Diagnostic Flow Table B-1
Piston and cylinder head cleaning
in Section 6A1

2. No.2 housing
3. No.3 housing
3. Rod
4. Shop cloth
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-19

As camshaft housing No.1 (1) retains camshaft in proper
position as to thrust direction, make sure to first fit No.1 hous-
ing to No.1 journal of camshaft securely.

After applying engine oil to housing bolts, tighten them tem-
porarily first. Then tighten them by following sequence as
shown in figure.
Tighten a little at a time and evenly among bolts and repeat
tightening sequence three to four times before they are tight-
ened to specified torque.
Special Tool
(A): 09919-16010
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
5) Install camshaft oil seal.
After applying engine oil to oil seal lip, press-fit camshaft oil
seal till oil seal surface becomes flush with housing surface.
6) Install camshaft timing belt pulley (1) to camshaft (2) after
installing dwell pin to camshaft.
With locking camshaft as shown in figure, tighten pulley bolt to
specified torque.
Tightening Torque
(b): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
7) Install cylinder head cover to cylinder head as previously out-
lined.
8) Install timing belt, timing belt outside cover, crankshaft pulley,
water pump pulley and water pump belt as previously outlined.
9) Install distributor case and distributor.
Refer to Section 6F for installation.
10) Install air cleaner assembly as previously outlined.
11) Connect negative cable at battery.
12) Adjust ignition timing.
Refer to Section 6F for adjustment.

2
IN
EX (A)
1
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-9
VALVE LASH (CLEARANCE)
1) Remove negative cable at battery.
2) Remove cylinder head cover referring to item “Cylinder Head
cover”.
3) Remove engine under cover of right side from body.
4) Using special tool and wrench (1), turn crankshaft pulley clock-
wise until “V” mark (2) (in white paint) on pulley aligns with “0”
(zero) calibrated on timing belt cover.
Special Tool
(A): 09919-16020
5) See if the rocker arms of No.1 cylinder are off the respective cam
lobes (of camshaft); if so, valves (1), (2), (5) and (7) in figure are
ready for clearance checking and adjustment. Check valve
lashes at valves (1), (2), (5) and (7).
If the rocker arms of No.4 cylinder are off the respective cam
lobes, check valve lashes at valves (3), (4), (6) and (8).
NOTE:
When checking valve clearance, insert thickness gauge be-
tween camshaft and cam-riding face of rocker arm.

1. Thickness gauge IN
EX
360
IN
EX
6A1-10 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
6) If valve lash is out of specification, adjust it to specification by
turning adjusting screw after loosening lock nut.
After adjustment, tighten lock nut to specified torque while hold-
ing adjusting screw stationary, and then make sure again that
valve lash is within specification.
Valve
clearance
When cold
(Coolant tempera-
ture is 15 – 25C
or 59 – 77F)When hot
(Coolant tempera-
ture is 60 – 68C
or 140 – 154F)
specifica-
tionIntake0.13 – 0.17 mm
(0.005 – 0.007 in.)0.18 – 0.22 mm
(0.007 – 0.009 in.)
Exhaust0.23 – 0.27 mm
(0.009 – 0.011 in.)0.28 – 0.32 mm
(0.011 – 0.013 in.)
Special Tool
(A): 09917-18211
Tightening Torque
(a): 12 N
.m (1.2 kg-m, 9.0 lb-ft)
7) After checking and adjusting valve lashes at valves (1), (2), (5)
and (7), (or (3), (4), (6) and (8)) rotate crankshaft exactly one full
turn (360) and check the same at valves (3), (4), (6) and (8) (or
(1), (2), (5) and (7)). Adjust them as necessary.
8) After checking and adjusting all valves, reverse removal proce-
dure for installation.

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-15
1. Injector coupler
2. TP sensor
3. Water hose
4. Vacuum hose
5. ISC actuator
6. Fuel return hose
7. Fuel feed hose
1. Injector coupler
Good No good
2) Install throttle body to EFE heater and tighten bolts to specified
torque.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Install accelerator cable to throttle valve lever and cable brack-
et.
4) Connect fuel, cooling water and vacuum hoses to throttle body,
and clamp securely.
5) Connect TP sensor and injector couplers securely.
6) Refill cooling system referring to Section 6B.
7) Connect negative cable at battery.
8) With engine “OFF” and ignition switch “ON”, check for fuel
leaks around fuel line connection.
9) Install air cleaner assembly referring to Section 6A.
10) Upon completion of installation, start engine and check for fuel
leaks and engine coolant leaks.
Adjust cable play to specification according to procedure de-
scribed in ACCELERATOR CABLE ADJUSTMENT.
FUEL INJECTOR
ON-VEHICLE INSPECTION
1) With battery negative cable disconnected, disconnect injector
coupler.
2) Connect ohmmeter to each injector terminal and measure resis-
tance.
Resistance of injector: 0.5 – 1.5 Ω at 20C (68F)
If resistance is out of specification, replace fuel injector.
3) Connect injector coupler.
4) Remove air cleaner assembly without disconnecting IAT sensor
coupler.
5) Check that fuel is injected out in conical shape from fuel injector
when cranking or running engine.
If no fuel is injected, check wiring harness for continuity and cou-
plers for proper connection referring to “DIAGNOSTIC FLOW
TABLE B-1”.
If fuel is not injected out in conical shape, replace injector.
6) Check injector for fuel leakage after injection is stopped (i.e., af-
ter cranking or engine stop).
Replace if leakage exists.
Fuel leakage: Less than 1 drop/min.
7) Install air cleaner assembly.

6E1-34 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
1. Tank pipe
2. Purge pipe
3. Air pipe
4. Blow air
1. Tank pressure
control valve
2. Orange side3. Black side
4. To canister
5. From fuel tank
EVAP CANISTER INSPECTION
WARNING:
DO NOT SUCK nozzles on EVAP canister. Fuel vapor inside
EVAP canister is harmful.
1) Disconnect vacuum hoses from EVAP canister and remove
EVAP canister.
2) When air is blown into tank pipe, there should be no restriction
of flow through purge pipe and air pipe.
If operation differs from above description, EVAP canister must
be replaced.
3) Install EVAP canister and connect hoses to canister.
TANK PRESSURE CONTROL VALVE INSPECTION
WARNING:
DO NOT SUCK air through tank pressure control valve.
Fuel vapor inside the valve is harmful.
1) Remove tank pressure control valve.
2) Air should pass through valve smoothly from fuel tank side
(black side of tank pressure control valve) to orange side when
blown hard.
3) From orange side, even when blown softly, air should come out
of black side.
4) If air doesn’t pass though valve in step 2) or hard blow is required
in step 3), replace tank pressure control valve.
5) Install tank pressure control valve.
NOTE:
When connecting tank pressure control valve between
hoses, refer to figure at the left for installing direction.
PCV SYSTEM
NOTE:
Be sure to check that there is no obstruction in PCV valve or
its hoses before adjusting engine idle speed, for obstructed
PCV valve or hose hampers its accurate adjustment.
PCV HOSE INSPECTION
Check hoses for connection, leakage, clog and deterioration.
Replace as necessary.

6E2
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-1
GENERAL DESCRIPTION6E2- 2 . . . . . . . . . . . . . .
AIR INTAKE SYSTEM 6E2- 6. . . . . . . . . . . . . . . . . .
FUEL DELIVERY SYSTEM 6E2- 7. . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E2- 8. . . . . .
Engine and Emission Control Input /
Output Table 6E2- 9. . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSISSee Section 6. . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE6E2-13 . . . . . . . . . . . . . . . .
Accelerator Cable Adjustment 6E2-13. . . . . . . . . .
Idle Speed/Idle Air Control (IAC)
Duty Inspection 6E2-14. . . . . . . . . . . . . . . . . . . . .
AIR INTAKE SYSTEM 6E2-15. . . . . . . . . . . . . . . . . .
Throttle Body 6E2-15. . . . . . . . . . . . . . . . . . . . . . . .
Idle Air Control Valve 6E2-17. . . . . . . . . . . . . . . . .
FUEL DELIVERY SYSTEM 6E2-18. . . . . . . . . . . . . .
Fuel Pressure Inspection 6E2-18. . . . . . . . . . . . . .
Fuel Pump 6E2-21. . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pressure Regulator 6E2-22. . . . . . . . . . . . . . .
Fuel Injector 6E2-23. . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E2-27. . . . . .
ECM / PCM 6E2-27. . . . . . . . . . . . . . . . . . . . . . . . . .
MAP Sensor 6E2-27. . . . . . . . . . . . . . . . . . . . . . . . .
TP Sensor 6E2-28. . . . . . . . . . . . . . . . . . . . . . . . . . .
IAT Sensor 6E2-29. . . . . . . . . . . . . . . . . . . . . . . . . .
ECT Sensor 6E2-30. . . . . . . . . . . . . . . . . . . . . . . . . Heated Oxygen Sensor -1 and -2 6E2-31. . . . . . .
Camshaft Position Sensor 6E2-32. . . . . . . . . . . . .
Crankshaft Position Sensor 6E2-32. . . . . . . . . . . .
Vehicle Speed Sensor 6E2-33. . . . . . . . . . . . . . . . .
Fuel Level Sensor (gauge) 6E2-33. . . . . . . . . . . . .
Main Relay, Fuel Pump Relay and
Radiator Fan Control Relay 6E2-33. . . . . . . . . . .
Fuel Cut Operation (Inspection) 6E2-34. . . . . . . .
Radiator Fan Control System 6E2-34. . . . . . . . . .
System Inspection 6E2-34. . . . . . . . . . . . . . . . . .
Radiator Fan 6E2-34. . . . . . . . . . . . . . . . . . . . . . .
EMISSION CONTROL SYSTEM 6E2-35. . . . . . . . .
EGR System 6E2-35. . . . . . . . . . . . . . . . . . . . . . . . .
EVAP Control System 6E2-36. . . . . . . . . . . . . . . . .
EVAP Canister Purge Inspection 6E2-36. . . . . .
Vacuum Passage Inspection 6E2-37. . . . . . . . .
Vacuum Hose Inspection 6E2-37. . . . . . . . . . . .
EVAP Canister Purge Valve
Inspection 6E2-37. . . . . . . . . . . . . . . . . . . . . . . .
EVAP Canister Inspection 6E2-38. . . . . . . . . . .
PCV System 6E2-38. . . . . . . . . . . . . . . . . . . . . . . . .
PCV Hose Inspection 6E2-38. . . . . . . . . . . . . . .
PCV Valve Inspection 6E2-38. . . . . . . . . . . . . . .
SPECIAL TOOLS6E2-39 . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS6E2-39 . . . . . . . . . . . . . . . . . . . . .
SECTION 6E2
ENGINE AND EMISSION CONTROL SYSTEM
(SFI FOR G13)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to “Air Bag System Components and Wiring Location View” under “Gener-
al Description” in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and “Service Precau-
tions” under “On-Vehicle Service” in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
“LOCK” position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS