2000 SUZUKI SWIFT check oil

4. Guide seal
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-29
7) Remove oil pump assembly (1) after removing bolts (2).
DISASSEMBLY
1) Remove oil level gauge guide bolt (3) and pull out guide (2) from
oil pump (1).
2) Remove rotor plate (1).
3) Remove outer rotor (1) and inner rotor (2).
INSPECTION

Check oil seal lip for fault or other damage. Replace as necessary.

6A1-30 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
NOTE:
When installing oil seal (1), press-fit it till its end face is flush
with oil pump case (2) end face.

Check outer and inner rotors, rotor plate, and oil pump case for
excessive wear or damage.
MEASUREMENT

Radial clearance
Check radial clearance between outer rotor (1) and case, using
thickness gauge.
If clearance exceeds its limit, replace outer rotor or case.
Limit on radial clearance between outer rotor and case:
0.200 mm (0.079 in.)

Side clearance
Using straight edge and thickness gauge, measure side clear-
ance.
Limit on side clearance: 0.10 mm (0.0039 in.)
ASSEMBLY
1) Wash, clean and then dry all disassembled parts.
2) Apply thin coat of engine oil to inner (2) and outer rotors (1), oil
seal lip portion, and inside surfaces of oil pump case and plate.
3) Install outer and inner rotors to pump case.

(a)
1. Oil pump
1. No. 1 bolts (short)
2. No. 2 bolts (long)
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-31
4) Install rotor plate. Tighten 5 screw securely.
After installing plate, check to be sure that gears turn smoothly
by hand.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
5) Apply engine oil to guide seal (3) and install guide seal and guide
(2).
INSTALLATION
1) Install two oil pump pins and oil pump gasket to cylinder block.
Use a new gasket.
2) To prevent oil seal lip from being damaged or upturned when
installing oil pump to crankshaft, fit special tool (Oil seal guide)
to crankshaft, and apply engine oil to special tool.
Special Tool
(A): 09926-18210
3) Install oil pump to cylinder block.
As there are 2 types of oil pump bolts, refer to figure for their cor-
rect use and tighten them to specified torque.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
4) Install rubber seal between oil pump and water pump.

6A1-32 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
5) Install timing pulley key (2) and crank timing belt pulley (3) and
crankshaft pulley pin (1). Refer to figure for proper installation
of these parts.
With crankshaft locked using flat end rod or the like (5), tighten
crank timing belt pulley bolt (4) to specified torque.
Tightening Torque
(a): 130 N
.m (13.0 kg-m, 94.0 lb-ft)
6) Install timing belt, tensioner, oil pump strainer, oil pan and other
parts as previously outlined.
7) Check to ensure that all removed parts are back in place. Rein-
stall any necessary parts which have not been reinstalled.
8) Adjust water pump drive belt tension referring to Section 6B.
9) Adjust power steering pump belt tension or A / C compressor
belt tension, if equipped.
Refer to Section 0B.
10) Refill engine with engine oil referring to “ENGINE OIL
CHANGE” in Section 0B.
11) Connect negative cable at battery.
12) After completing installation, check oil pressure by running en-
gine.

A: Timing belt side
B: Flywheel side
6A1-38 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
INSTALLATION
1) Apply engine oil to rocker arm shaft and rocker arms.
2) Check O-ring for damage or deterioration. Install O-ring to rock-
er arm shaft.
3) Install rocker arm shaft (3) with shaft bolt holes (4) facing up,
rocker arm (exhaust side) (2) and rocker arm spring (1).
4) Install rocker arm shaft bolts and tighten them to specified
torque.
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
5) Fill small amount of engine oil into arm pivot holding part (3) of
rocker arm shaft. Install rocker arm (intake side) (1) with clips (2)
to rocker arm shaft.
6) Apply engine oil to cams and journals on camshaft and put cam-
shaft on cylinder head. Install camshaft housing to camshaft and
cylinder head.

Apply engine oil to sliding surface of each housing against
camshaft journal.

Apply sealant to mating surface of No.6 housing which will
mate with cylinder head.
“A” Sealant: 99000-31110

6A1-40 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
1. O-ring2
10) Using special tool, tighten pulley bolt to specified torque.
Tightening Torque
(a): 60 N
.m (6.0 kg-m, 43.5 lb-ft)
Special Tool
(A): 09917-68221
11) Install belt tensioner, timing belt, outside cover, crankshaft
pulley and water pump belt as previously outlined.
12) After applying sealant to part “A” as shown in figure, install
CMP sensor case (2) (Distributorless ignition coil case) to cyl-
inder head and tighten its fixing bolts to specified torque.
“A” Sealant: 99000-31110
Tightening Torque
(a): 11 N
.m (1.1 kg-m, 8.0 lb-ft)
13) Adjust valve clearance as previously outlined.
14) Install cylinder head cover and air cleaner outlet hose.
15) Check to ensure that the following parts are back in place:

Ignition coil assemblies

High tension cords

CMP sensor coupler

Couplers to ignition coil assembly

Other removed parts which have not been reinstalled
16) Connect negative cable at battery.
17) Confirm that ignition timing is within specification referring to
Section 6F.

3
2. Breather hose
3. PCV valve4. High-tension cords
5. Ignition coil assembly
6. Ignition coil coupler
A: Camshaft pulley side
B: CMP sensor case side
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-43
9) Remove cylinder head cover (1) as previously outlined.
Loosen all valve lash adjusting screws fully.
10) Remove timing belt and camshaft as previously outlined.
11) Disconnect exhaust pipe from exhaust manifold and remove
exhaust manifold stiffener (if equipped).
12) Loosen cylinder head bolts in such order as indicated in figure
and remove them.
13) Check all around cylinder head for any other parts required to
be removed or disconnected and remove or disconnect what-
ever necessary.
14) Remove cylinder head with intake manifold, exhaust manifold
CMP sensor case, using lifting device if necessary.

A: Valve spring retainer side
B: Valve spring seat side
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-51
5) Install new valve stem seal (1) to valve guide.
After applying engine oil to seal and spindle of special tool (Valve
guide installer handle), fit oil seal to spindle, and then install seal
to valve guide by pushing special tool by hand.
After installing, check to be sure that seal is properly fixed to
valve guide.
Special Tool
(A): 09917-98221
(B): 09916-58210
NOTE:

Do not reuse seal once disassembled. Be sure to install
new seal.

When installing, never tap or hit special tool with a ham-
mer or else. Install seal to guide only by pushing special
tool by hand. Tapping or hitting special tool may cause
damage to seal.
6) Install valve to valve guide.
Before installing valve to valve guide, apply engine oil to stem
seal, valve guide bore, and valve stem.
7) Install valve spring and spring retainer.
Each valve spring has top end (large-pitch (1) end) and bottom
end (small-pitch (2) end). Be sure to position spring in place with
its bottom end (small-pitch end) facing the bottom (valve spring
seat side).
8) Using special tools (Valve lifter), compress valve spring and fit
two valve cotters (1) into groove in valve stem.
Special Tool
(A): 09916-14510
(B): 09916-14910
(C): 09916-84511