2000 SUZUKI SWIFT check oil

Main fuse Ignition switch
Main fuseMalfunction indicator lamp in combination meter
Relay box“IG COIL METER”
6-42 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE A-3 ECM (PCM) POWER AND GROUND CIRCUIT CHECK – MIL
DOESN’T LIGHT AT IGNITION SWITCH ON AND ENGINE DOESN’T
START THOUGH IT IS CRANKED UP
CIRCUIT DESCRIPTION
When the ignition switch tuned ON, the main relay turns ON (the contact point closes) and the main power is sup-
plied to ECM (PCM).
INSPECTION
STEPACTIONYESNO
1Main Relay Operating Sound Check
Is operating sound of main relay heard at ignition switch ON?Go to Step 5.Go to Step 2.
2Main Relay Check
1) Turn OFF ignition switch and remove main relay (1).
2) Check for proper connection to main relay (1) at terminal
3 and 4.
3) Check resistance between each two terminals. See Fig. 1
and 2.
Between terminals 1 and 2: Infinity
Between terminals 3 and 4: 100 – 120 Ω
4) Check that there is continuity between terminals 1 and 2
when battery is connected to terminals 3 and 4. See Fig. 3.
Is main relay in good condition?Go to Step 3.Replace main
relay.
3Fuse Check
Is main “FI” fuse in good condition?Go to Step 4.Check for short in
circuits connected
to this fuse.
4ECM (PCM) Power Circuit Check
1) Turn OFF ignition switch, disconnect connectors from ECM
(PCM) and install main relay.
2) Check for proper connection to ECM (PCM) at terminals
C03-20, C02-2, C02-15 and C02-22.
3) If OK, then measure voltage between terminal C03-20 and
ground, C02-22 and ground with ignition switch ON.
Is each voltage 10 – 14 V?Go to Step 5.“B/W”, “W/R” or
“Bl / B” circuit
open.

To generatorTo other sensor
Heater Ignition
switch Main
fuse
“IG COIL METER”
ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-57
DTC P0135 HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT
MALFUNCTION (SENSOR-1)
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
DTC will set when A or B condition is met.
A:

Low voltage at terminal C01-8 when engine is
running at high load.
B:

High voltage at terminal C01-8 when engine is
running under condition other than above.
2 driving cycle detection logic, Continuous
monitoring.
HO2S-1 heater circuit open or shorted to ground

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON, start engine and keep it at idle for 1 min.
3) Start vehicle and depress accelerator pedal fully for 5 sec. or longer.
4) Stop vehicle.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.

6-62 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
To other sensor
Heater Ignition
switch Main
fuse
“IG COIL METER”
To ignition coilTo other sensor
DTC P0141 HEATED OXYGEN SENSOR (HO2S) HEATER CIRCUIT
MALFUNCTION (SENSOR-2)
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE
DTC will set when A or B condition it met.
A. Low voltage at terminal C02-19 for specified time after engine
start or while engine running at high load.
B. High voltage at terminal C02-19 while engine running under
other than above condition.
2 driving cycle detection logic, continuous monitoring.
HO2S-2 heater circuit open or shorted
to ground

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF once and then ON.
2) Clear DTC, start engine and warm up engine to normal operating temperature.
3) Keep it at 2000 r / min for 2 min.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-69
Below
specified value DTC DETECTING CONDITION
POSSIBLE CAUSE

Engine under other than high revolution condition

Not on rough road

Engine speed changing rate

Manifold absolute
pressure changing rate

Throttle opening changing rate

Misfire rate per 200 or 1000 engine revolutions (how
much and how often crankshaft revolution speed
changes) is higher than specified value
Engine overheating

Vacuum leaks (air inhaling) from air intake system

Ignition system malfunction (spark plug(s), high-
tension cord(s), ignition coil assembly)

Fuel pressure out of specification

Fuel injector malfunction (clogged or leakage)

Engine compression out of specification

Valve lash (clearance) out of specification

Manifold absolute pressure sensor malfunction

Engine coolant temp. sensor malfunction

PCV valve malfunction

EVAP control system malfunction
DTC CONFIRMATION PROCEDURE
WARNING:

When performing a road test, select a place where there is no traffic or possibility of a traffic accident
and be very careful during testing to avoid occurrence of an accident.

Road test should be carried out with 2 persons, a driver and a tester.
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Check vehicle and environmental condition for:
–Altitude (barometric pressure): 2400 m, 8000 ft or less (560 mmHg, 75 kPa or more)
–Ambient temp.: –10C, 14F or higher
–Intake air temp.: 70C, 158F or lower
–Engine coolant temp.: –10 – 11 0C, 14 – 230F
4) Start engine and keep it at idle for 2 min. or more.
5) Check DTC in “DTC” mode and pending DTC in “ON BOARD TEST” or “PENDING DTC” mode.
6) If DTC is not detected at idle, consult usual driving based on information obtained in “Customer complaint analy-
sis” and “Freeze frame data check”.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-75
Fig. 1 for Step 3 Fig. 2 for Step 5
“a”: Air gap
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Is DTC P1500 (Engine starter signal circuit
malfunction) detected?Go to DTC P1500
Diag. Flow Table.Go to Step 3.
3Check CMP Sensor for Resistance.
1) Measure resistance of CMP sensor by referring to
“CMP SENSOR (PICK UP COIL) RESISTANCE”
in SECTION 6F.
Is resistance within specified value?Go to Step 4.Faulty CMP sensor.
4Check Wire Harness.
1) With ignition switch at OFF position, disconnect
ECM (PCM) electrical connectors.
2) Measure resistance from terminal “C01-2” to
“C01-10” of ECM (PCM) connector. See Fig. 1.
Is resistance within 185 – 275 Ω at 20C (68F)?Go to Step 5.“W” or “Or” wire open
or short.
Poor connection of
CMP sensor
connector terminal.
5Check Air Gap Between Rotor Tooth and Sensor. See
Fig. 2.
1) Remove Distributor cap.
2) Visually inspect CMP sensor signal rotor for
damage.
3) Measure air gap by referring “SIGNAL ROTOR
AIR GAP” in Section 6F.
Was any damage found?Faulty CMP sensor
signal rotor.Poor connection of
ECM (PCM)
connector terminal.
If OK, substitute a
known-good ECM
(PCM) and recheck
CMP.

6-80 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
Fig. 1 for Step 1
Main
fuseIgnition switch“IG COIL METER”
Radiator fan
relay
Radiator fan motor
DTC P0480 RADIATOR FAN CONTROL SYSTEM MALFUNCTION
CIRCUIT DESCRIPTION
DTC DETECTING CONDITIONPOSSIBLE CAUSE

Low voltage at terminal C02-20 when engine coolant
temp. is below 91C, 195F.
2 driving cycle detection logic, continuous monitoring.
“B/W” or “BI” circuit open or short

Radiator fan relay malfunction

ECM (PCM) malfunction
DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Warm up engine until radiator cooling fan starts to operate.
4) Check pending DTC in “ON BOARD TEST” or “PENDING DTC” mode and DTC in “DTC” mode.

“IG
COIL
METER”
Main
fuseIgnition
switch
Main
relayTo other circuits
Injector resistor Fuel injector
6-96 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE B-1 FUEL INJECTOR CIRCUIT CHECK
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Injector Circuit Check
1) Check injector circuit for short.
Is fuel injected from injector at ignition switch ON?“Y/B” wire shorted to
ground or faulty
injector.
If wire and injector is
as specified
respectively and then
substitute known-
good ECM (PCM) and
recheck.Go to Step 3.
3Injector Check
1) Check injector for fuel Injection referring to FUEL
INJECTOR ON-VEHICLE INSPECTION in
Section 6E1.
Is fuel injected from injector at engine cranking?Go to Step 4.Go to Step 5.
4Injector Leakage Check
1) Check injector for leaks referring to FUEL
INJECTOR ON-VEHICLE INSPECTION in
Section 6E1.
Is it in good condition?Injector and its circuit
are in good condition.Faulty fuel injector.
5Check Injector for Operating Sound.
1) Using sound scope, check injector for operating
sound at engine cranking.
Is it detected?Proceed to DIAG.
FLOW TABLE B-2 and
B-3.Go to Step 6.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-19
Operation
VISUAL INSPECTION
Visually check following parts and systems.
INSPECTION ITEM
REFERRING SECTION

Engine oil ––––– level, leakage

Engine coolant ––––– level, leakage

Fuel ––––– level, leakage

A / T fluid ––––– level, leakage

Air cleaner element ––––– dirt, clogging

Battery ––––– fluid level, corrosion of terminal

Water pump belt ––––– tension, damage

Throttle cable ––––– play, installation

Vacuum hoses of air intake system ––––– disconnection,
looseness, deterioration, bend

Connectors of electric wire harness ––––– disconnection, friction

Fuses ––––– burning

Parts ––––– installation, bolt ––––– looseness

Parts ––––– deformation

Other parts that can be checked visually
Also check following items at engine start, if possible

Malfunction indicator lamp

Charge warning lamp

Engine oil pressure warning lamp

Engine coolant temp. meter

Fuel level meter

Tachometer, if equipped

Abnormal air being inhaled from air intake system

Exhaust system ––––– leakage of exhaust gas, noise

Other parts that can be checked visuallySection 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 0B
Section 6E2
Section 8
Section 6
Section 6H
Section 8 (Section 6 for pressure check)
Section 8
Section 8