2000 SUZUKI SWIFT Lamp

2. Ground
1. Throttle body
2. ISC actuator
coupler
3. TP sensor
coupler
4. Fuel injector
coupler
5. EFE heater
coupler
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-7
INSTALLATION
1) Install throttle body to intake manifold. (Refer to Section 6E.)
2) Install intake manifold gasket to cylinder head. Use a new gas-
ket.
3) Install intake manifold (1) with throttle body to cylinder head.

Install clamps (3) as shown in figure, and tighten bolts and
nuts to specification.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Connect breather hose to PCV valve.
5) Connect vacuum hoses.
6) Connect coolant hoses.
7) Connect fuel return and feed hoses to throttle body.
8) Connect electric lead wire.
9) Connect accelerator cable to throttle body.
10) Install air cleaner assembly to throttle body.
11) Check to ensure that all removed parts are back in place.
Reinstall any necessary parts which have not been reinstalled.
12) Refill cooling system.
13) Connect negative cable at battery.
14) Upon completion of installation, start engine and check for fuel
leaks and engine coolant leaks.
After warming up engine, adjust accelerator cable play to spec-
ification according to description in Section 6E.

1. Exhaust manifold
2. Gasket
3. Cover
4. Heated oxygen sensor
5. Pipe seal
6. Exhaust pipe
7. WU-TWC (if equipped)
8. Exhaust pipe bolt : Tightening Torque
: Do not reuse
6A-8 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
EXHAUST MANIFOLD
WARNING:
To avoid danger of being burned, do not service exhaust
system while it is still hot.
Service should be performed after system cools down.
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect heated oxygen sensor coupler.
Release its wire from clamps.
3) Disconnect exhaust pipe (1) from exhaust manifold (or WU-
TWC (2)).
4) Remove WU-TWC stiffener (3). (if equipped)
5) Remove exhaust manifold cover (2). (for vehicle with WU-TWC)
6) Remove exhaust manifold (1) with WU-TWC (if equipped) and
its gasket from cylinder head.

2. WU-TWC
ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE) 6A-9
INSTALLATION
1) Install manifold gasket to cylinder head.
Before installing gasket, check it for deterioration or damage,
and replace as necessary.
2) Install exhaust manifold (1).
Tighten manifold bolts and nuts to specified torque.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Install exhaust manifold cover (2).
4) Install pipe seal, and then connect exhaust pipe (1).
Before installing pipe seal, check it for deterioration or damage,
and replace as necessary.
Tighten pipe bolts to specified torque.
Tightening Torque
(c): 43 N
.m (4.3 kg-m, 31.5 lb-ft)
5) Install WU-TWC stiffener (3). (if equipped)
6) Connect heated oxygen sensor coupler.
7) Clamp its wire securely.
8) Connect negative cable at battery.
9) Check exhaust system for exhaust gas leakage.

6A-24 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
UNIT REPAIR OVERHAUL
ENGINE ASSEMBLY
REMOVAL
1) Relieve fuel pressure according to procedure described in
“FUEL PRESSURE RELIEF PROCEDURE” of Section 6.
2) Remove engine hood after disconnecting front window washer
hose.
3) Disconnect battery cables at battery and remove battery and
its tray.
4) Drain cooling system.
5) Remove air cleaner assembly.
6) Remove radiator with cooling fan. Refer to Section 6B for re-
moval.
7) Disconnect the following electric wire harness.

High-tension cord from ignition coil

Distributor

EGR valve

ECT sensor

ISC actuator

Ground wire harness from intake manifold

TP sensor

Fuel injector

Oil pressure gauge

A / C compressor pressure switch (if equipped)

Heated oxygen sensor

Generator

Starter

Back-up light switch (For M / T model)

Battery negative cable from transmission

Shift switch of A / T (For A / T model)

Direct clutch and 2nd brake solenoids of A / T (For A / T model)

Vehicle speed sensor on A / T (For A / T model)
And release above wire harness from clamps.
8) Disconnect the following vacuum hose.

Brake booster hose from intake manifold.

Canister purge hose from EVAP canister purge valve.

Pressure sensor hose from intake manifold.
9) Disconnect fuel return hose and fuel feed hose from fuel feed
and return pipes.
10) Disconnect heater inlet and outlet hoses.

1. Rear mounting
2. Rear mounting No.2
bracket
3. Rear mounting No.1
bracket
4. Rear mounting
bracket5. Left mounting
body bracket
6. Left mounting
7. Left mounting bracket
8. Right mounting bracket
9. Right mounting
For M / T model
For A / T model
1. Rear mounting
2. Rear mounting No.2
bracket
3. Rear mounting No.1
bracket
4. Left mounting No.1
bracket
5. Stopper6. Left mounting
7. Left mounting No.2
bracket
8. Right mounting bracket
9. Right mounting
10. Torque rod bracket
11. Stiffener
12. Torque rod
6A-26 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
INSTALLATION
1) Lift engine with transmission into engine compartment, but do
not remove lifting device.
2) Install right side engine mounting to its bracket.
3) Install left side engine mounting and its bracket.
4) Install rear mounting to body.
5) Tighten bolts and nuts of all parts installed in above steps 2),
3) and 4) to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
6) Remove lifting device.
7) Reverse removal procedures for installation of remainder.

Push in each drive shaft joint fully so that snap ring engages
with differential gear or center bearing support.
Use care not to damage oil seal lip when inserting.

Clamp electric wires securely.
8) Adjust clutch pedal free travel referring to Section 7C. (For M / T
model)
Adjust gear select cable and oil pressure control cable referring
to Section 7B. (For A / T model)
9) Adjust gear shift control lever referring to Section 7A. (For M / T
model)
10) Refill transmission with gear oil. (A / T fluid for A / T model) refer-
ring to Section 0B.
11) Refill engine with engine oil referring to Section 0B.
12) Refill cooling system referring to Section 6B.
13) Adjust A / C compressor drive belt referring to Section 0B. (if
equipped)
14) Upon completion of installation, verify that there is no fuel leak-
age, coolant leakage, transmission oil leakage or exhaust gas
leakage at each connection.
15) Adjust accelerator cable play referring to Section 6E.

3
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-11
AIR CLEANER ELEMENT
REMOVAL
1) Disconnect air cleaner outlet hose from case after loosening its
clamp (2) and removing bolt (1) shown in figure.
2) Remove air cleaner cap (3) from case by unhooking its clamps,
then take out air cleaner element.
INSPECTION
Check air cleaner element for dirt. Replace excessively dirty ele-
ment.
CLEAN
Blow off dust by compressed air from air outlet side of element.
INSTALLATION
Reverse removal procedure for installation.

6A1-12 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
AIR CLEANER OUTLET HOSE
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect resonator after loosening its clamp.
3) Disconnect breather hose from air cleaner outlet hose.
4) Disconnect IAT sensor wire at coupler.
5) Remove bolt and then air cleaner outlet hose after loosening its
clamps.
INSTALLATION
Reverse removal procedure for installation, noting the following.

Clamp each hose securely.

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-15
7) Disconnect the following electric lead wires and release clamp:

Ground wires (5) from intake manifold

TP sensor (3)

IAC valve (4)

Fuel injectors

EVAP canister purge valve (2)

MAP sensor (6)

EGR valve (1)
8) Disconnect the following hoses:

Brake booster hose (1) from intake manifold

Canister purge hose (3) from EVAP canister purge valve

Engine cooling water (coolant) hose (2) from IAC valve

PCV hose (4)

Breather hose from cylinder head
9) Disconnect fuel feed hose (2) from pipe (1), and disconnect fuel
return hose (3) from fuel pressure regulator.