2000 SUZUKI SWIFT Oxygen sensor

6A-24 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
UNIT REPAIR OVERHAUL
ENGINE ASSEMBLY
REMOVAL
1) Relieve fuel pressure according to procedure described in
“FUEL PRESSURE RELIEF PROCEDURE” of Section 6.
2) Remove engine hood after disconnecting front window washer
hose.
3) Disconnect battery cables at battery and remove battery and
its tray.
4) Drain cooling system.
5) Remove air cleaner assembly.
6) Remove radiator with cooling fan. Refer to Section 6B for re-
moval.
7) Disconnect the following electric wire harness.

High-tension cord from ignition coil

Distributor

EGR valve

ECT sensor

ISC actuator

Ground wire harness from intake manifold

TP sensor

Fuel injector

Oil pressure gauge

A / C compressor pressure switch (if equipped)

Heated oxygen sensor

Generator

Starter

Back-up light switch (For M / T model)

Battery negative cable from transmission

Shift switch of A / T (For A / T model)

Direct clutch and 2nd brake solenoids of A / T (For A / T model)

Vehicle speed sensor on A / T (For A / T model)
And release above wire harness from clamps.
8) Disconnect the following vacuum hose.

Brake booster hose from intake manifold.

Canister purge hose from EVAP canister purge valve.

Pressure sensor hose from intake manifold.
9) Disconnect fuel return hose and fuel feed hose from fuel feed
and return pipes.
10) Disconnect heater inlet and outlet hoses.

: Tightening Torque
: Do not reuse
1. Exhaust manifold
2. Gasket
3. Cover
4. Heated oxygen sensor
7. Gasket
8. Exhaust No.1 pipe.
21
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-17
EXHAUST MANIFOLD
WARNING:
To avoid danger of being burned, do not service exhaust
system while it is still hot.
Service should be performed after system cools down.
REMOVAL
1) Disconnect negative cable at battery.
2) Disconnect heated oxygen sensor coupler.
Release its wire from clamps.
3) Disconnect exhaust No.1 pipe (1) from WU-TWC.
4) Remove WU-TWC stiffener (2) (if equipped).
5) Remove exhaust manifold (1) and its gasket from cylinder head.

(b)
(a)
6A1-18 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)
INSTALLATION
1) Install new gaskets to cylinder head.
2) Install exhaust manifold.
Tighten bolts and nuts to specified torque.
Tightening Torque
(a): 32 N
.m (3.2 kg-m, 23.5 lb-ft)
3) Install exhaust manifold cover(s) (1).
4) Connect oxygen sensor coupler (3) and clamp (2) its wire se-
curely.
5) Tighten exhaust No.1 pipe to manifold nuts and exhaust man-
ifold stiffener bolt.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
6) Connect negative cable at battery.
7) Check exhaust system for exhaust gas leakage.

6A1-42 ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE)

Ignition coil assembly

Ground wires from
intake manifold

EVAP canister purge
valve

ECT sensor
Injectors, TP sensor and
IAC valve wires at the
coupler

Heated oxygen sensor 1

MAP sensor
5) Remove intake manifold rear stiffener (1) and generator adjust
arm reinforcement (2) from intake manifold.
6) Disconnect the following electric wires:
and then release above wire harnesses from clamps.
7) Disconnect the following hoses:

Brake booster hose (1)

EVAP canister purge hose (3) from purge valve

Radiator inlet hose

Heater inlet hose

IAC valve outlet (2)
8) Disconnect fuel feed (2) and return hoses (3) from fuel delivery
pipe (1).

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-65
12) Disconnect the following electric wires:

Ignition coil assembly

Ground wires from intake manifold

Engine oil pressure switch

EVAP canister purge valve (if equipped)

Engine coolant temp. sensor

Fuel injectors

Power steering pressure switch (if equipped)

Oxygen sensor-1

Back-up light switch (M / T)

Transmission range switch (A / T)

A/T vehicle speed sensor (A / T)

Solenoid coupler (A / T)

Generator

Starter

Battery negative cable from transmission

TP sensor

IAC valve

CMP sensor

MAP sensor
and then release wire harnesses from clamps.
13) Disconnect the following hoses:

Canister purge hose (2) from EVAP canister purge valve

Brake booster hose (1) from intake manifold

Radiator outlet hose from inlet pipe

Heater inlet and outlet hose from heater unit
14) Disconnect fuel feed (2) and return hoses (3) from fuel delivery
pipe (1).

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-1
GENERAL DESCRIPTION6E1- 2 . . . . . . . . . . . . . .
AIR AND FUEL DELIVERY SYSTEM 6E1- 4. . . . .
ELECTRONIC CONTROL SYSTEM 6E1- 5. . . . . .
ON-VEHICLE SERVICE6E1- 8 . . . . . . . . . . . . . . . .
General 6E1- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accelerator Cable Adjustment 6E1- 8. . . . . . . . . .
Idle Speed Inspection 6E1- 8. . . . . . . . . . . . . . . . .
AIR AND FUEL DELIVERY SYSTEM 6E1- 9. . . . .
Fuel Pressure 6E1- 9. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump 6E1-11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body 6E1-12. . . . . . . . . . . . . . . . . . . . . . . .
Fuel injector 6E1-15. . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E1-17. . . . . .
ECM 6E1-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAP Sensor 6E1-18. . . . . . . . . . . . . . . . . . . . . . . . .
TP Sensor 6E1-19. . . . . . . . . . . . . . . . . . . . . . . . . . .
IAT Sensor 6E1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
ECT Sensor 6E1-21. . . . . . . . . . . . . . . . . . . . . . . . .
Heated Oxygen Sensor -1 and -2 6E1-23. . . . . . .
Vehicle Speed Sensor 6E1-24. . . . . . . . . . . . . . . . .
Fuel Level Sensor (Gauge) 6E1-24. . . . . . . . . . . . Crankshaft Position Sensor 6E1-25. . . . . . . . . . . .
Main Relay 6E1-25. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay 6E1-26. . . . . . . . . . . . . . . . . . . . .
Fuel Injector Resistor 6E1-26. . . . . . . . . . . . . . . . .
Fuel Cut Operation 6E1-26. . . . . . . . . . . . . . . . . . .
ISC System 6E1-26. . . . . . . . . . . . . . . . . . . . . . . . . .
ISC Actuator 6E1-27. . . . . . . . . . . . . . . . . . . . . . . . .
CTP Switch 6E1-28. . . . . . . . . . . . . . . . . . . . . . . . . .
ISC Actuator Relay 6E1-29. . . . . . . . . . . . . . . . . . .
EFE Heater Control System 6E1-29. . . . . . . . . . . .
EFE Heater 6E1-29. . . . . . . . . . . . . . . . . . . . . . . . . .
EFE Heater Relay 6E1-30. . . . . . . . . . . . . . . . . . . .
Radiator Fan Control System 6E1-30. . . . . . . . . .
Radiator Fan Control Relay 6E1-31. . . . . . . . . . . .
Radiator Fan 6E1-31. . . . . . . . . . . . . . . . . . . . . . . . .
EMISSION CONTROL SYSTEM 6E1-32. . . . . . . . .
EVAP Control System 6E1-32. . . . . . . . . . . . . . . . .
PCV System 6E1-34. . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6E1-36 . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS6E1-36 . . . . . . . . . . . . . . . . . . . .
SECTION 6E1
ENGINE AND EMISSION CONTROL SYSTEM
(TBI FOR G10)
WARNING:
For vehicles equipped with a Supplemental Inflatable Restraint Air Bag System:

Service on or around Air Bag System Components or Wiring must be performed only by an authorized
Suzuki dealer. Please observe all WARNINGS and SERVICE PRECAUTIONS in Section 9J under “On-
Vehicle Service” and the Air Bag System Component and Wiring Location view in Section 9J before
performing service on or around Air Bag System Components or Wiring. Failure to follow WARNINGS
could result in unintended air bag deployment or could render the air bag inoperative. Either of these
two conditions may result in severe injury.

SDM can maintain sufficient voltage to cause a deployment of air bags for up to 15 seconds after igni-
tion switch is turned to “LOCK” position, battery is disconnected or fuse powering SDM is removed.
Work must be started after 15 seconds from the time.
NOTE:
For the descriptions for vehicle without warm up three way catalytic converter (WU TWC), refer to the same
section of the Service Manual mentioned in the FOREWORD of this manual.
CONTENTS

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-3
1. Tank pressure control valve
2. Fuel liquid separator
3. Fuel tank
4. Fuel pump
5. Fuel level sensor (gauge)
6. Fuel filter
7. Fuel pressure regulator
8. Throttle body
9. Fuel injector
10. MAP sensor
11. TP sensor
12. ISC actuator
(including CTP switch)
13. PCV valve
14. Exhaust manifold
15. Intake manifold
16. Heated oxygen sensor-117. Warm up three way catalytic
convertor (WU-TWC)
(if equipped)
18. Three way catalytic convertor
19. IAT sensor
20. ECT sensor
21. EFE heater
22. EVAP canister purge valve
23. EVAP canister
24. Heated oxygen sensor-2
25. Radiator fan motor
26. Ignition coil
27. Ignitor
28. Electric load
29. A / C amplifier (if equipped)
30. Camshaft position sensor
31. Crankshaft position sensor32. VSS (on A / T)
33. Transmission range sensor
(switch) (A / T)
34. Shift solenoid-A (A / T)
35. Shift solenoid-B (A / T)
36. Data link connector
37. VSS (in combination meter of
M / T vehicle)
38. PSP switch (if equipped)
39. Malfunction indicator lamp
40. Transmission range sensor
(switch) (A / T)
41. Main (Ignition) switch
42. Main fuse
43. Battery
44. Immobilizer indicator lamp

INFORMATION SENSORS
1. MAP sensor
2. TP sensor
3. IAT sensor
4. ECT sensor
5. Heated oxygen sensor-1
6. VSS
7. Ignition coil
8. Battery
9. Distributor (CMP sensor)
10. A / C controller (if equipped)
11. CKP sensor
12. CTP switch (in ISC actuator)
13. Heated oxygen sensor-2CONTROLLED DEVICES
a : Fuel injector
b : EVAP canister purge valve
c : Fuel pump relay
d : Malfunction indicator lamp
e : ISC actuator
f : Radiator fan control relay
g : Ignitor
h : EFE heater relay
i : ISC actuator relayOTHERS
A : ECM (PCM)
B : Main relay
C : EVAP canister
D : Injector resistor
E : EFE heater
F : Electric load diode
G : Data link connector
ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-5
The electronic control system consists of 1) various
sensors which detect the state of engine and driving
conditions, 2) ECM which controls various devices
according to the signals from the sensors and 3) vari-
ous controlled devices.
Functionally, it is divided into following sub systems:

Fuel injection control system

Idle speed control system
Fuel pump control system

A/C control system (if equipped)

Radiator fan control system

Evaporative emission control system

EFE heater control system

Oxygen sensor heater control system

Ignition control system

A / T control system
ELECTRONIC CONTROL SYSTEM