2000 SUZUKI SWIFT Spark

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-71
INSPECTION
STEPACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE
DIAG. FLOW
TABLE“.
2Is there DTC other than Fuel system (DTC P0171 / P0172)
and misfire (DTC P0300-P0304)?Go to applicable
DTC Diag.
Flow Table.Go to Step 3.
3Check Ignition System.
1) Remove spark plugs and check them for;

Air gap: 1.0 – 1.1 mm (0.040 – 0.043 in.) See Fig. 1.

Carbon deposits

Insulator damage

Plug type
If abnormality is found, adjust, clean or replace.
2) Disconnect all injector connectors. See Fig. 2.
3) Connect spark plugs to high tension cords and then ground
spark plugs.
4) Crank engine and check that each spark plug sparks.
Are above check results satisfactory?Go to Step 4.Check ignition
system parts
(Refer to Section
6F1).
4Check Fuel Pressure (Refer to Section 6E2 for details).
1) Release fuel pressure from fuel feed line.
2) Install fuel pressure gauge. See Fig. 3.
3) Check fuel pressure.
With fuel pump operating
and engine at stop : 270 – 310 kPa, 2.7 – 3.1 kg / cm
2,
38.4 – 44.0 psi.
At specified idle speed : 200 – 240 kPa, 2.0 – 2.4 kg / cm
2,
28.4 – 34.1 psi.
Is measured value as specified?
Go to Step 5.Go to Diag. Flow
Table B-3 fuel
pressure check.
5Check Fuel Injectors and Circuit.
1) Using sound scope (1) or such, check operating sound of
each injector (2) when engine is running. Cycle of
operating sound should very according to engine speed.
See Fig 4.
If no sound or an unusual sound is heard, check injector
circuit (wire or coupler) or injector.
2) Turn ignition switch OFF and disconnect a fuel injector
connector.
3) Check for proper connection to fuel injector at each
terminal. See Fig. 5.
4) If OK, then check injector resistance.
Injector Resistance: 12 – 13 ohm at 20C (68F)
5) Carry out steps 1) and 3) on each injector.
6) Check each injector for injected fuel volume referring to
Section 6E2. See Fig. 6.
Injected Fuel Volume: 38 – 48 cc / 15 sec (1.28 / 1.34 –
1.62 / 1.69 US / Imp. oz / 15 sec)
7) Check each injector for fuel leakage after injector closed.
Fuel Leakage: Less than 1 drop / min.
Is check result in step 1) and 3) to 7) satisfactory?Go to Step 6.Check injector
circuit or replace
fuel injector(s).

6-1-72 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
Disconnect connectors when checking plugs
for spark1. Fuel delivery pipe
2. Fuel feed hose
3. FUel pressure
gauge & 3 way joint
STEPACTIONYESNO
6Check PCV valve for clogging (See Section 6E2).
Is it in good condition?Go to Step 7.Replace PCV valve.
7Check EVAP Canister Purge Valve for Closing.
1) Disconnect purge hose (1) from EVAP canister.
2) Place finger against the end of disconnected hose.
3) Check that vacuum is not felt there, when engine is
cool and running at idle. See Fig. 7.
Is vacuum felt?Check EVAP
control system
(See Section 6E2).Go to Step 8.
8Check intake manifold pressure sensor for performance
(See DTC P0105 Diag. Flow Table).
Is it in good condition?Go to Step 9.Repair or replace.
9Check engine coolant temp. sensor for performance
(See Section 6E2).
Is it in good condition?Go to Step 10.Replace engine
coolant temp.
sensor.
10Check parts or system which can cause engine rough
idle or poor performance.
–Engine compression (See Section 6A1).
–Valve lash (See Section 6A1).
–Valve timing (Timing belt installation. See Section 6A1).
Are they in good condition?Check wire harness
and connection of
ECM (PCM) ground,
ignition system and
fuel injector for
intermittent open
and short.Repair or replace.
Fig. 1 for Step 3 Fig. 2 for Step 3 Fig. 3 for Step 4
Fig. 4 for Step 5 Fig. 5 for Step 4 Fig. 6 for Step 5
Fig. 7 for Step 7

1
2
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-5
ON-VEHICLE SERVICE
COMPRESSION CHECK
Check compression pressure on all four cylinders as follows:
1) Warm up engine.
2) Stop engine after warming up.
NOTE:
After warming up engine, place transmission gear shift le-
ver in “Neutral” (shift selector lever to “P” range for A / T
model), and set parking brake and block drive wheels.
3) Remove ignition coil assemblies (1) and all spark plugs (2) refer-
ring to Section 6F.
WARNING:
Failure in disconnecting couplers from ignition coil as-
semblies can cause spark to occur in engine room possi-
bly resulting in a dangerous explosion.
4) Disconnect fuel injector wire harness at couplers (2).
5) Install special tools (Compression gauge) into spark plug hole.
Special Tool
(A): 09915-64510-001
(B): 09915-64510-002
(C): 09915-64530
(D): 09915-67010
6) Disengage clutch (to lighten starting load on engine) for M / T
model, and depress accelerator pedal all the way to make
throttle valve full-open.
7) Crank engine with fully charged battery, and read the highest
pressure on compression gauge.
Compression pressure
Standard1400 kPa
(14.0 kg / cm
2, 199.0 psi)
Limit1100 kPa
(11.0 kg / cm
2, 156.4 psi)
Max. difference between any
two cylinders100 kPa
(1.0 kg / cm
2, 14.2 psi)
8) Carry out steps 5) through 7) on each cylinder to obtain four
readings.
9) After checking, connect couplers to fuel injectors securely and
install spark plugs and ignition coil assemblies.

12 W / R “N”-range signal (A / T)
13 R Heated oxygen sensor-2
14 Y / R “D”-range signal (A / T)
15 R / W “R”-range signal (A / T)
16 Lg / B A / C SW signal
17 R / W EGR valve (stepper motor coil 4)
18 P / G Radiator fan relay
19 Y / Bl Fuel pump relay
20 —— ———
21 W / B “P”-range signal (A / T)
22 P / Bl Fuel level gauge
23 R / B “L”-range signal (A / T)
24 —— ———
1 V Malfunction indicator lamp
Vehicle speed sensor (M / T)
Output shaft speed sensor (+)
(A / T)
3 —— ———
4 G / W Shift solenoid – A (A / T)
5 Gr Throttle position (TP) sensor
6 B / W Ignition switch signal
7 Y / B Data link connector
Output shaft speed sensor (–)
(A / T)
9 —— ———
10 G GND for HO2S-2
11 G / Or Shift solenoid – B (A / T)
12 —— ———
13 —— ———
14 —— ———
15 —— ———
16 Br Tachometer signal
17 B / Y Engine start signal
CON-
NECTORTERMINALWIRE
COLORCIRCUITCON-
NECTORTERMINALWIRE
COLORCIRCUIT
20
Br / Y 19
Br / W
C02 C01C02
C03
Wire color
B : Black
B / Or : Black / Orange
B / W : Black / White
B / Y : Black / Yellow
Bl : Blue
Bl / Or : Blue / Orange
Bl / B : Blue / Black
Bl / R : Blue / Red
Bl / Y : Blue / Yellow
Br : Brown
Br / W : Brown / White
Br / Y : Brown / Yellow
G : Green
G / Or : Green / Orange
G / R : Green / Red
G / W : Green / White
Gr : Gray
Gr / R : Gray / Red
Lg / B : Lightgreen / Black
Lg / R : Lightgreen / RedP : Pink
P / Bl : Pink / Blue
P / G : Pink / Green
V : Violet
V / G : Violet / Green
V / R : Violet / Red
V / W : Violet / White
W : White
W / B : White / Black
W / R : White / Red
R : Red
R / B : Red / Black
R / Bl : Red / Blue
R / G : Red / Green
R / W : Red / White
R / Y : Red / Yellow
Y / B : Yellow / Black
Y / Bl : Yellow / Blue
Y / R : Yellow / Red
2
P
8
Bl
6E2-12 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
1 B Ground for ECM / PCM
2 B / Or Ground for drive circuit
3 B / Or Ground for drive circuit
4 V / R Canister purge valve
5 G / W Power steering pressure switch
6 V / W IAC valve
7 Bl Heater of HO2S-1
8 Bl / Or No.4 fuel injector
9 Bl / R No.1 fuel injector
10 G Ground for sensor circuit
11 B / W CMP sensor
12 —— ———
13 R Heated oxygen sensor-1
14 Lg / R Coolant temp. sensor
15 Gr / R Intake air temp. sensor
16 —— ———
17 Br / Y Electric load (+)
18 —— ———
IG coil assembly for
No.2 and 3 spark plugs
IG coil assembly for
No.1 and 4 spark plugs
21 Bl / B No.2 fuel injector
22 P Power supply for sensor
23 W CKP sensor (+)
24 B CKP sensor (–)
25 —— ———
26 G MAP sensor
27 —— ———
28 V / G Immobilizer indicator lamp
29 —— ———
30 —— ———
31 Bl / Y No.3 fuel injector
1 G / R A / C compressor clutch
2 R / Y EGR valve (stepper motor coil 1)
3 R / G Data link connector
4 Lg / B Heater of HO2S-2
5 R / B Power source
6 R / B Power source
7 W Backup power source
8 R EGR valve (stepper motor coil 3)
9 R / Bl EGR valve (stepper motor coil 2)
10 Gr Ground for main relay
11 Y / B “2”-range signal (A / T)

6E2-24 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
Inspection
WARNING:
As fuel is injected in this inspection, perform in a well venti-
lated area and away from open flames.
Use special care to prevent sparking when connecting and
disconnecting test lead to and from battery.
1) Install injector (1) and fuel pressure regulator (2) to special tool
(injector checking tool).
Special Tool
(A): 09912-58421
2) Connect special tools (hose and attachment) to fuel feed hose
(3) of vehicle.
Special Tool
(B): 09912-58431
3) Connect special tool (test lead) to injector.
Special Tool
(C): 09930-88530

6F
IGNITION SYSTEM 6F-1
GENERAL DESCRIPTION6F- 1 . . . . . . . . . . . . . .
DIAGNOSIS6F- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE6F- 5 . . . . . . . . . . . . . . . .
Ignition Spark Test 6F- 5. . . . . . . . . . . . . . . . . . . .
High-Tension Cords 6F- 5. . . . . . . . . . . . . . . . . . .
Spark Plugs 6F- 6. . . . . . . . . . . . . . . . . . . . . . . . .
Noise Suppressor 6F- 6. . . . . . . . . . . . . . . . . . . . Ignition Coil 6F- 7. . . . . . . . . . . . . . . . . . . . . . . . . .
Igniter 6F- 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distributor 6F- 8. . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Timing 6F- 9. . . . . . . . . . . . . . . . . . . . . . .
Distributor Unit 6F-10. . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6F-11 . . . . . . . . . . . . . . . . . . . . . .
The ignition system used for this vehicle has an elec-
tronic ignition control system and consists of the fol-
lowing parts.

ECM
It detects the engine condition through the signals
from the sensors, determines the most suitable igni-
tion timing and time for electricity to flow to the pri-
mary coil and sends a signal to the power unit.

Power unit (Igniter)
It turns ON and OFF the primary current of the igni-
tion coil according to the signal from ECM.

Ignition coil
When the ignition coil primary current is turned OFF,
a high voltage is induced in the secondary winding.

Distributor
It distributes a high voltage current to each plug.
High-tension cords and spark plugs.

CMP sensor (Camshaft position Sensor)
Located in the distributor, it converts the crank angle
into voltage variation and sends it to ECM. For its
details, refer to Section 6E1.

TP sensor, ECT sensor and MAP sensor
For their details, refer to Section 6E.
In electronic ignition control system, the ECM is pro-
grammed for the best ignition timing under every en-
gine condition. Receiving signals which indicate the
engine condition from the sensors, e.g., engine revo-
lution, intake air pressure, coolant temperature, etc.,
it selects the most suitable ignition timing from its
memory and operates the power unit.
Thus ignition timing is controlled to yield the best en-
gine performance.
For more information, refer to Section 6E1.
SECTION 6F
IGNITION SYSTEM
WARNING:
For vehicles equipped with a Supplemental Inflatable Restraint Air Bag System:

Service on or around Air Bag System Components or Wiring must be performed only by an authorized
Suzuki dealer. Please observe all WARNINGS and SERVICE PRECAUTIONS in Section 9J under “On-
Vehicle Service” and the Air Bag System Component and Wiring Location view in Section 9J before
performing service on or around Air Bag System Components or Wiring. Failure to follow WARNINGS
could result in unintended air bag deployment or could render the air bag inoperative. Either of these
two conditions may result in severe injury.

SDM can maintain sufficient voltage to cause a deployment of air bags for up to 10 seconds after igni-
tion switch is turned to “LOCK” position, battery is disconnected or fuse powering SDM is removed.
Work must be started after 15 seconds from the time.
CONTENTS
GENERAL DESCRIPTION

1. Battery
2. Main fuse
3. Ignition switch
4. Main relay
5. Ignition coil
6. Igniter
7. Noise suppressor
8. Distributor
9. Rotor
10. Signal rotor
11. Pick up coil
12. Spark plug
To combination
meter
6F-2 IGNITION SYSTEM

IGNITION SYSTEM 6F-3
DIAGNOSIS
ConditionPossible CauseCorrection
Engine cranks, but will
not start or hard to start
Blown fuse for ignition coil

Loose connection or disconnection of lead wire or
high-tension cord(s)

Faulty high-tension cord(s)

Faulty spark plug(s)

Cracked rotor or cap

Maladjusted signal rotor air gap

Faulty ignition coil

Faulty noise suppressor

Faulty CMP sensor

Faulty igniter

Faulty ECM (or PCM)

Maladjusted ignition timingReplace
Connect securely
Replace
Adjust, clean or replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Adjust
Poor fuel economy or
engine performance
Incorrect ignition timing

Faulty spark plug(s) or high-tension cord(s)

Faulty ECM (or PCM)Adjust
Adjust, clean or replace
Replace
DIAGNOSTIC FLOW TABLE
STEPACTIONYESNO
1Was “Engine Diagnostic Flow Table” in SECTION 6
performed?Go to Step 2.Go to “Engine
Diagnostic Flow
Table” in SECTION 6.
2Ignition Spark Test
1) Check all spark plug for condition and type,
referring to “Spark Plugs” in this section.
2) If OK, perform ignition spark test, referring to
“Ignition Spark Check” in this section.
Is spark emitted from all spark plugs?Go to Step 11 on the
next page.Go to Step 3.
3Diagnostic Trouble Code (DTC) Check
1) Check DTC stored in ECM (or PCM), referring to
“Diagnostic Trouble Code (DTC) Check” in
SECTION 6.
Is DTC stored?Go to applicable flow
table corresponding to
that code No. in
SECTION 6.Go to Step 4.
4Electrical Connection and Noise Suppressor Check
1) Check ignition coil for electrical connection and
noise suppressor for conductivity.
Are they good condition?Go to Step 5.Repair or replace.
5High-tension Cord Check
1) Check high-tension cord for resistance, referring
to “High-tension Cords” in this section.
Is check result satisfactory?Go to Step 6.Replace high-tension
cord(s).