2000 SUZUKI SWIFT Injector

1. Fuel pump
2. Fuel filter
3. Throttle body
4. Fuel injector
5. Fuel pressure regulator6. Special tool
(Fuel pressure gauge &
3-way joint)
7. Fuel feed line
8. Fuel return line
6-100 ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10)
TABLE B-3 FUEL PRESSURE CHECK
INSPECTION
STEPACTIONYESNO
1Check Fuel Pressure (Refer to Section 6E1 for details).
1) Release fuel pressure from fuel feed line.
2) Install fuel pressure gauge.
3) Check fuel pressure by repeating ignition switch
ON and OFF. See Fig. 1.
Is fuel pressure then 160 – 210 kPa (1.6 – 2.1 kg / cm
2,
22.7 – 29.9 psi)?
Go to Step 2.Go to Step 4.
2Is 90 kPa (0.9 kg / cm2, 12.8 psi) or higher fuel
pressure retained for 1 minute after fuel pump is
stopped at Step 1?Normal fuel pressure.Go to Step 3.
31) Start engine and warm it up to normal operating
temperature.
2) Keep it running at specified idle speed.
Is fuel pressure then within 90 – 140 kPa
(0.9 – 1.4 kg / cm
2, 12.8 – 20.0 psi)?
Normal fuel pressure.
Clogged vacuum
passage for fuel
pressure regulator
or

Faulty fuel pressure
regulator.
4Is there fuel leakage from fuel feed line hose, pipe or
their joint?Fuel leakage from
hose, pipe or joint.Go to Step 10.
5Was fuel pressure higher than specification in Step 1?Go to Step 6.Go to Step 7.
61) Disconnect fuel return hose from throttle body and
connect new return hose to it.
2) Insert the other end of new return hose into
approved gasoline container.
3) Operate fuel pump.
Is specified fuel pressure obtained then?Restricted fuel return
hose or pipe.Faulty fuel pressure
regulator.
7Was no fuel pressure supplied in Step 1?Go to Step 8.Go to Step 9.

ENGINE GENERAL INFORMATION AND DIAGNOSIS (TBI FOR G10) 6-101
Fig. 1 for Step 1
1. Fuel pressure gauge & 3way joint
STEPACTIONYESNO
8With fuel pump operated and fuel return hose
blocked by pinching it, is fuel pressure applied?Faulty fuel pressure
regulator.Shortage of fuel or fuel
pump or its circuit
defective (refer to B-2
FUEL PUMP ANDITS
CIRCUIT CHECK).
91) Operate fuel pump.
2) With fuel return hose blocked by pinching it, check
fuel pressure.
Is it 450 kPa (4.5 kg / cm
2, 63.9 psi) or more?
Faulty fuel pressure
regulator.
Clogged fuel filter,

Restricted fuel feed
hose or pipe,

Faulty fuel pump or

Fuel leakage from
hose connection in
fuel tank.
101) Disconnect fuel return hose from throttle body and
connect new return hose to it.
2) Insert the other end of new return hose into
approved gasoline container.
3) Check again if specified pressure is retained.
While doing so, does fuel come out of return hose?Faulty fuel pressure
regulator.
Fuel leakage from
injector,

Fuel leakage from
between injector
and throttle body,

Faulty fuel pump
(faulty check valve
in fuel pump) or

Fuel leakage from
fuel pressure
regulator
diaphragm.

6-1-2 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
DTC P0300 Random Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0301 Cylinder 1 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0302 Cylinder 2 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0303 Cylinder 3 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0304 Cylinder 4 Misfire
Detected 6-1- 69. . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0335 CKP Sensor Circuit
Malfunction 6-1- 73. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0340 CMP Sensor Circuit
Malfunction 6-1- 75. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0400 EGR Flow Malfunction 6-1- 78. . . .
DTC P0420 Catalyst System
Efficiency Below Threshold 6-1- 81. . . . . . . . . .
DTC P0443 Purge Control Valve Circuit
Malfunction 6-1- 84. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0480 Radiator Fan Control
System Malfunction 6-1- 85. . . . . . . . . . . . . . . . .
DTC P0500 Vehicle Speed Sensor
Malfunction 6-1- 87. . . . . . . . . . . . . . . . . . . . . . . .
DTC P0505 Idle Control System
Malfunction 6-1- 91. . . . . . . . . . . . . . . . . . . . . . . . DTC P0601 Internal Control Module
Memory Check Sum Error 6-1- 93. . . . . . . . . . .
DTC P1450 Barometric Pressure
Sensor Low / High Input 6-1- 94. . . . . . . . . . . . .
DTC P1451 Barometric Pressure Sensor
Performance Problem 6-1- 94. . . . . . . . . . . . . . .
DTC P1500 Engine Starter Signal
Circuit Malfunction 6-1- 96. . . . . . . . . . . . . . . . . .
DTC P1510 ECM (PCM) Back-up
Power Supply Malfunction 6-1- 97. . . . . . . . . . .
Table B-1 Fuel Injector Circuit Check 6-1- 98. . .
Table B-2 Fuel Pump and Its Circuit
Check 6-1- 99. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 Fuel Pressure Check 6-1-101. . . . . . . .
Table B-4 A / C Signal Circuits Check 6-1-103. . .
Table B-5 PSP Switch Signal Circuit
Check 6-1-104. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-6 Electric Load Signal Circuit
Check 6-1-105. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-7 Radiator Cooling Fan Control
System Check 6-1-106. . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6-1-108 . . . . . . . . . . . . . . . . . . . . .

HOSE CONNECTION
Clamp securely at a position 3 to
7mm (0.12–0.27 in.) from hose end. With short pipe, fit hose as far as it reaches pipe joint as
shown.
Hose
Pipe
ClampClamps securely at a position
3 to 7 mm (0.12–0.27 in.)
from hose end.
With following type pipe, fit hose as far as its peripheral
projection as shown.
Clamp securely at a position
3 to 7 mm (0.12–0.27 in.)
from hose end.
With bent pipe, fit hose as its bent part as shown or till pipe
is about 20 to 30 mm (0.79–1.18 in.) into the hose.
Clamp securely at a
position 3 to 7 mm
(0.12–0.27 in.) from hose
end.
With straight pipe, fit hose till pipe is, about 20 to 30 mm
(0.79–1.18 in.) into the hose.
Hose
20 to 30 mm
(0.79–1.18 in.)
Clamp
6-1-4 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
PRECAUTION ON FUEL SYSTEM SERVICE

Work must be done with no smoking, in a well-ventilated area and
away from any open flames.

As fuel feed line (between fuel pump and fuel delivery pipe) is still
under high fuel pressure even after engine was stopped, loosen-
ing or disconnecting fuel feed line directly may cause dangerous
spout of fuel to occur where loosened or disconnected.
Before loosening or disconnecting fuel feed line, make sure to re-
lease fuel pressure according to “FUEL PRESSURE RELIEF
PROCEDURE”. A small amount of fuel may be released after the
fuel line is disconnected. In order to reduce the chance of person-
al injury, cover the fitting to be disconnected with a shop cloth. Put
that cloth in an approved container when disconnection is com-
pleted.

Never run engine with fuel pump relay disconnected when engine
and exhaust system are hot.

Fuel or fuel vapor hose connection varies with each type of pipe.
When reconnecting fuel or fuel vapor hose, be sure to connect
and clamp each hose correctly referring to left figure Hose Con-
nection.
After connecting, make sure that it has no twist or kink.

When installing injector or fuel delivery pipe, lubricate its O-ring
with spindle oil or gasoline.

When connecting fuel pipe flare nut, first tighten flare nut by hand
and then tighten it to specified torque.

6-1-20 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ENGINE BASIC INSPECTION
This check is very important for troubleshooting when ECM (PCM) has detected no DTC and no abnormality has
been found in visual inspection.
Follow the flow table carefully.
STEP
ACTIONYESNO
1Was “ENGINE DIAG. FLOW TABLE” performed?Go to Step 2.Go to “ENGINE DIAG.
FLOW TABLE”.
2Check battery voltage.
Is it 11 V or more?Go to Step 3.Charge or replace
battery.
3Is engine cranked?Go to Step 4.Go to “DIAGNOSIS”
in Section 6G.
4Does engine start?Go to Step 5.Go to Step 7.
5Check idle speed as follows:
1) Warm up engine to normal operating temp.
2) Shift transmission to neutral position for M / T
(“P” position for A / T).
3) All of electrical loads are switched off.
4) Check engine idle speed with scan tool.
See Fig. 1.
Is it 700 – 800 r / min?Go to Step 6.“ENGINE DIAGNO-
SIS TABLE” in this
section.
6Check ignition timing as follows:
1) Using SUZUKI scan tool, select “MISC” mode on
SUZUKI scan tool and fix ignition timing to initial
one. See Fig. 2.
2) Remove air cleaner bolt and shift air cleaner
position to observe ignition timing.
3) Using timing light (1), check initial ignition timing.
See Fig. 3.
Is it 5 ± 3 BTDC at specified idle speed?“ENGINE DIAGNO-
SIS TABLE” in this
section.Check ignition control
related parts referring
to Section 6F1.
7Check fuel supply as follows:
1) Check to make sure that enough fuel is filled in fuel
tank.
2) Turn ON ignition switch for 2 seconds and then
OFF. See Fig. 4.
Is fuel return pressure (returning sounds) felt from fuel
feed hose (1) when ignition switch is turned ON?Go to Step 9.Go to Step 8.
8Check fuel pump for operating.
1) Was fuel pump operating sound heard from fuel
filler for about 2 seconds after ignition switch ON
and stop?Go to “DIAG. FLOW
TABLE B-3”.Go to “DIAG. FLOW
TABLE B-2”.
9Check ignition spark as follows:
1) Disconnect injector couplers.
2) Remove spark plugs and connect them to high
tension cords.
3) Ground spark plugs.
4) Crank engine and check if each spark plug sparks.
Is it in good condition?Go to Step 10.Go to “DIAGNOSIS”
in Section 6F1.
10Check fuel injector for operation as follows:
1) Install spark plugs and connect injector
connectors.
2) Using sound scope (1), check operating sound of
each injector (2) when cranking engine. See Fig. 5.
Was injector operating sound heard from all
injectors?“ENGINE DIAGNO-
SIS TABLE” in this
section.Go to “DIAG. FLOW
TABLE B-1”.

6-1-24 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ConditionPossible CauseReferring Item
Overheating
Inoperative thermostat

Poor water pump performance

Clogged or leaky radiator

Improper engine oil grade

Clogged oil filter or oil strainer

Poor oil pump performance

Faulty radiator fan control system

Dragging brakes

Slipping clutch

Blown cylinder head gasketThermostat in Section 6B
Water pump in Section 6B
Radiator in Section 6B
Engine oil and oil filter change in
Section 0B
Oil pressure check in Section 6A1
Oil pressure check in Section 6A1
Radiator fan control system in
Section 6E2
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Cylinder head in Section 6A1
Poor gasoline
mileageIgnition system out of order

Leaks or loose connection of high-tension cord

Faulty spark plug (improper gap, heavy deposits
and burned electrodes, etc.)
Engine and emission control system out of
order

Malfunctioning EGR valve

High idle speed

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty EGR valve

Faulty fuel injector(s)

Faulty ECM (PCM)
Low compression
Others

Poor valve seating

Dragging brakes

Slipping clutch

Thermostat out of order

Improper tire pressure
High-tension cords in Section 6F1
Spark plugs in Section 6F1
EGR system in Section 6E2
Refer to item “Improper engine
idle speed” previously outlined
TP sensor, ECT sensor or MAP
sensor in Section 6E2
EGR system in Section 6E2
Diagnostic Flow Table B-1
Previously outlined
Valves inspection in Section 6A1
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C
Thermostat in Section 6B
Refer to Section 3F
Excessive engine
oil consumptionOil leakage

Blown cylinder head gasket

Leaky camshaft oil seals
Oil entering combustion chamber

Sticky piston ring

Worn piston and cylinder

Worn piston ring groove and ring

Improper location of piston ring gap

Worn or damaged valve stem seal

Worn valve stem
Cylinder head in Section 6A1
Camshaft in Section 6A1
Piston cleaning in Section 6A1
Pistons and cylinders inspection
in Section 6A1
Pistons inspection in Section 6A1
Pistons assembly in Section 6A1
Valves removal and installation in
Section 6A1
Valves inspection in Section 6A1

ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13) 6-1-25
ConditionPossible CauseReferring Item
Engine hesitates
(Momentary lack of
response as
accelerator is
depressed.
Can occur at all
vehicle speeds.
Usually most severe
when first trying to
make vehicle move,
as from a stop sign.)Ignition system out of order

Spark plug faulty or plug gap out of adjustment

Leaky high-tension cord
Fuel system out of order

Fuel pressure out of specification
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
Engine overheating
Low compression
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-3
EGR system in section 6E2
TP sensor, ECT sensor or MAP
sensor in Section 6E2
Diagnostic Flow Table B-1
Refer to “Overheating” section
Previously outlined
Surge
(Engine power
variation under
steady throttle or
cruise.
Feels like vehicle
speeds up and down
with no change in
accelerator pedal.)Ignition system out of order

Leaky or loosely connected high-tension cord

Faulty spark plug (excess carbon deposits,
improper gap, and burned electrodes, etc.)
Fuel system out of order

Variable fuel pressure
–Kinky or damaged fuel hose and lines
–Faulty fuel pump (clogged fuel filter)
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of MAP sensor

Faulty fuel injector

Faulty ECM (PCM)
High-tension cords in Section 6F1
Spark plugs in Section 6F1
Diagnostic Flow Table B-3
EGR system in Section 6E2
MAP sensor in Section 6E2
Diagnostic Flow Table B-1
Excessive
detonation
(Engine makes
continuously
sharp metallic
knocks that change
with throttle opening.
Sounds like pop corn
popping.)Engine overheating
Ignition system out of order

Faulty spark plug

Loose connection of high-tension cord
Fuel system out of order

Clogged fuel filter (faulty fuel pump) or fuel lines

Air inhaling from intake manifold or throttle body
gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Poor performance of ECT sensor or MAP sensor

Faulty fuel injector(s).

Faulty ECM (PCM)

Excessive combustion chamber depositsRefer to “Overheating” section
Spark plugs in Section 6F1
High-tension cords in Section 6F1
Diagnostic Flow Table B-1 or B-2
EGR system in Section 6E2
ECT sensor or MAP sensor in
Section 6E2
Diagnostic Flow Table B-1
Piston and cylinder head cleaning
in Section 6A1

6-1-26 ENGINE GENERAL INFORMATION AND DIAGNOSIS (SFI FOR G13)
ConditionPossible CauseReferring Item
Engine has no
powerIgnition system out of order

Faulty spark plug

Faulty ignition coil with ignitor

Leaks, loose connection or disconnection of
high-tension cord
Engine overheating
Fuel system out of order

Clogged fuel hose or pipe

Malfunctioning fuel pump

Air inhaling from intake manifold gasket or
throttle body gasket
Engine and emission control system out of
order

Malfunctioning EGR valve

Maladjusted accelerator cable play

Poor performance of TP sensor, ECT sensor or
MAP sensor

Faulty fuel injector(s)

Faulty ECM (PCM)
Low compression
Others

Dragging brakes

Slipping clutch
Spark plugs in Section 6F1
Ignition coil in Section 6F1
High-tension cords in Section 6F1
Refer to “Overheating” section
Diagnostic Flow Table B-3
Diagnostic Flow Table B-2
EGR system inspection in Section
6E2
Accelerator cable play in Section
6E2
TP sensor, ECT sensor or MAP
sensor in Section 6E2
Diagnostic Flow Table B-1
Previously outlined
Trouble diagnosis in Section 5
Trouble diagnosis in Section 7C