2000 SUZUKI SWIFT Injector

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-65
12) Disconnect the following electric wires:

Ignition coil assembly

Ground wires from intake manifold

Engine oil pressure switch

EVAP canister purge valve (if equipped)

Engine coolant temp. sensor

Fuel injectors

Power steering pressure switch (if equipped)

Oxygen sensor-1

Back-up light switch (M / T)

Transmission range switch (A / T)

A/T vehicle speed sensor (A / T)

Solenoid coupler (A / T)

Generator

Starter

Battery negative cable from transmission

TP sensor

IAC valve

CMP sensor

MAP sensor
and then release wire harnesses from clamps.
13) Disconnect the following hoses:

Canister purge hose (2) from EVAP canister purge valve

Brake booster hose (1) from intake manifold

Radiator outlet hose from inlet pipe

Heater inlet and outlet hose from heater unit
14) Disconnect fuel feed (2) and return hoses (3) from fuel delivery
pipe (1).

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-1
GENERAL DESCRIPTION6E1- 2 . . . . . . . . . . . . . .
AIR AND FUEL DELIVERY SYSTEM 6E1- 4. . . . .
ELECTRONIC CONTROL SYSTEM 6E1- 5. . . . . .
ON-VEHICLE SERVICE6E1- 8 . . . . . . . . . . . . . . . .
General 6E1- 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accelerator Cable Adjustment 6E1- 8. . . . . . . . . .
Idle Speed Inspection 6E1- 8. . . . . . . . . . . . . . . . .
AIR AND FUEL DELIVERY SYSTEM 6E1- 9. . . . .
Fuel Pressure 6E1- 9. . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump 6E1-11. . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Body 6E1-12. . . . . . . . . . . . . . . . . . . . . . . .
Fuel injector 6E1-15. . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRONIC CONTROL SYSTEM 6E1-17. . . . . .
ECM 6E1-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAP Sensor 6E1-18. . . . . . . . . . . . . . . . . . . . . . . . .
TP Sensor 6E1-19. . . . . . . . . . . . . . . . . . . . . . . . . . .
IAT Sensor 6E1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
ECT Sensor 6E1-21. . . . . . . . . . . . . . . . . . . . . . . . .
Heated Oxygen Sensor -1 and -2 6E1-23. . . . . . .
Vehicle Speed Sensor 6E1-24. . . . . . . . . . . . . . . . .
Fuel Level Sensor (Gauge) 6E1-24. . . . . . . . . . . . Crankshaft Position Sensor 6E1-25. . . . . . . . . . . .
Main Relay 6E1-25. . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel Pump Relay 6E1-26. . . . . . . . . . . . . . . . . . . . .
Fuel Injector Resistor 6E1-26. . . . . . . . . . . . . . . . .
Fuel Cut Operation 6E1-26. . . . . . . . . . . . . . . . . . .
ISC System 6E1-26. . . . . . . . . . . . . . . . . . . . . . . . . .
ISC Actuator 6E1-27. . . . . . . . . . . . . . . . . . . . . . . . .
CTP Switch 6E1-28. . . . . . . . . . . . . . . . . . . . . . . . . .
ISC Actuator Relay 6E1-29. . . . . . . . . . . . . . . . . . .
EFE Heater Control System 6E1-29. . . . . . . . . . . .
EFE Heater 6E1-29. . . . . . . . . . . . . . . . . . . . . . . . . .
EFE Heater Relay 6E1-30. . . . . . . . . . . . . . . . . . . .
Radiator Fan Control System 6E1-30. . . . . . . . . .
Radiator Fan Control Relay 6E1-31. . . . . . . . . . . .
Radiator Fan 6E1-31. . . . . . . . . . . . . . . . . . . . . . . . .
EMISSION CONTROL SYSTEM 6E1-32. . . . . . . . .
EVAP Control System 6E1-32. . . . . . . . . . . . . . . . .
PCV System 6E1-34. . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS6E1-36 . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS6E1-36 . . . . . . . . . . . . . . . . . . . .
SECTION 6E1
ENGINE AND EMISSION CONTROL SYSTEM
(TBI FOR G10)
WARNING:
For vehicles equipped with a Supplemental Inflatable Restraint Air Bag System:

Service on or around Air Bag System Components or Wiring must be performed only by an authorized
Suzuki dealer. Please observe all WARNINGS and SERVICE PRECAUTIONS in Section 9J under “On-
Vehicle Service” and the Air Bag System Component and Wiring Location view in Section 9J before
performing service on or around Air Bag System Components or Wiring. Failure to follow WARNINGS
could result in unintended air bag deployment or could render the air bag inoperative. Either of these
two conditions may result in severe injury.

SDM can maintain sufficient voltage to cause a deployment of air bags for up to 15 seconds after igni-
tion switch is turned to “LOCK” position, battery is disconnected or fuse powering SDM is removed.
Work must be started after 15 seconds from the time.
NOTE:
For the descriptions for vehicle without warm up three way catalytic converter (WU TWC), refer to the same
section of the Service Manual mentioned in the FOREWORD of this manual.
CONTENTS

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-3
1. Tank pressure control valve
2. Fuel liquid separator
3. Fuel tank
4. Fuel pump
5. Fuel level sensor (gauge)
6. Fuel filter
7. Fuel pressure regulator
8. Throttle body
9. Fuel injector
10. MAP sensor
11. TP sensor
12. ISC actuator
(including CTP switch)
13. PCV valve
14. Exhaust manifold
15. Intake manifold
16. Heated oxygen sensor-117. Warm up three way catalytic
convertor (WU-TWC)
(if equipped)
18. Three way catalytic convertor
19. IAT sensor
20. ECT sensor
21. EFE heater
22. EVAP canister purge valve
23. EVAP canister
24. Heated oxygen sensor-2
25. Radiator fan motor
26. Ignition coil
27. Ignitor
28. Electric load
29. A / C amplifier (if equipped)
30. Camshaft position sensor
31. Crankshaft position sensor32. VSS (on A / T)
33. Transmission range sensor
(switch) (A / T)
34. Shift solenoid-A (A / T)
35. Shift solenoid-B (A / T)
36. Data link connector
37. VSS (in combination meter of
M / T vehicle)
38. PSP switch (if equipped)
39. Malfunction indicator lamp
40. Transmission range sensor
(switch) (A / T)
41. Main (Ignition) switch
42. Main fuse
43. Battery
44. Immobilizer indicator lamp

1. Air cleaner
2. Throttle body
3. Fuel injector
4. Fuel pressure regulator
5. Intake manifold
6. Fuel filter
7. Fuel tank
8. Fuel pump
9. Fuel feed line
10. Fuel return line
11. Air
12. Fuel
13. Air/fuel mixture
6E1-4 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
The main components of this system are fuel tank,
fuel pump, fuel filter, throttle body (including fuel injec-
tor, fuel pressure regulator and idle speed control ac-
tuator), fuel feed line, fuel return line and air cleaner.
The fuel in the fuel tank is pumped up by the fuel
pump, filtered by the fuel filter and fed under pressure
to injector installed in throttle body. As the fuel pres-
sure applied to the fuel injector (the fuel pressure in
the fuel feed line) is always kept a certain amount
higher than the pressure in the intake manifold by the
fuel pressure regulator, the fuel is injected into the
throttle body in conic dispersion when the injectoropens according to the injection signal from ECM.
The fuel relieved by the fuel pressure regulator re-
turns through the fuel return line to the fuel tank.
The injected fuel is mixed with the air which has been
filtered through the air cleaner in the throttle body. The
air/fuel mixture is drawn through clearance between
throttle valve and bore.
Then the intake manifold distributes the air/fuel mix-
ture to each combustion chamber.
For the structure and operation of the fuel tank and fil-
ter, refer to SECTION 6C “ENGINE FUEL”.
AIR AND FUEL DELIVERY SYSTEM

INFORMATION SENSORS
1. MAP sensor
2. TP sensor
3. IAT sensor
4. ECT sensor
5. Heated oxygen sensor-1
6. VSS
7. Ignition coil
8. Battery
9. Distributor (CMP sensor)
10. A / C controller (if equipped)
11. CKP sensor
12. CTP switch (in ISC actuator)
13. Heated oxygen sensor-2CONTROLLED DEVICES
a : Fuel injector
b : EVAP canister purge valve
c : Fuel pump relay
d : Malfunction indicator lamp
e : ISC actuator
f : Radiator fan control relay
g : Ignitor
h : EFE heater relay
i : ISC actuator relayOTHERS
A : ECM (PCM)
B : Main relay
C : EVAP canister
D : Injector resistor
E : EFE heater
F : Electric load diode
G : Data link connector
ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-5
The electronic control system consists of 1) various
sensors which detect the state of engine and driving
conditions, 2) ECM which controls various devices
according to the signals from the sensors and 3) vari-
ous controlled devices.
Functionally, it is divided into following sub systems:

Fuel injection control system

Idle speed control system
Fuel pump control system

A/C control system (if equipped)

Radiator fan control system

Evaporative emission control system

EFE heater control system

Oxygen sensor heater control system

Ignition control system

A / T control system
ELECTRONIC CONTROL SYSTEM

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-7
CON-
NECTOR
C02TERMI-
NAL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26ECM ground
Power source (from main relay)
Blank
Blank
Blank
Blank
EVAP canister purge valve
Shift solenoid-B (A / T)
Shift solenoid-A (A / T)
Igniter
Idle speed control actuator
Fuel injector
Injector ground
Power source (from battery)
Power source (from main relay)
Idle speed control actuator relay
Malfunction indicator lamp
Immobilizer indicator lamp
Heater of HO2S-2
Radiator fan relay
Fuel pump relay
Main relay
Blank
Idle speed control actuator
EFE heater relay
Injector groundC031
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22Data link connector
Vehicle speed sensor (+) (A / T)
Vehicle speed sensor (M / T)
Transmission range sensor (switch)“2”
Transmission range sensor (switch)“N”
Transmission range sensor (switch)“P”
Blank
Blank
Heated oxygen sensor-2
Blank
Fuel level sensor (gauge)
Blank
Data link connector
Vehicle speed sensor (–) (A / T)
Transmission range sensor (switch)“L”
Transmission range sensor (switch)“D”
Transmission range sensor (switch)“R”
A / C ON (output) signal for A / C control module
(if equipped)
Electric load signal
A / C (input) signal from A / C control module
(if equipped)
Ignition switch
Blank
Blank CIRCUITCON-
NECTORTERMI-
NALCIRCUIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16Power source for sensors
Camshaft position sensor (+)
Crankshaft position sensor (+)
Closed throttle position switch
Manifold absolute pressure sensor
Throttle position sensor
Engine coolant temp. sensor
Heater of HO2S-1
Sensor ground
Camshaft position sensor (–)
Crankshaft position sensor (–)
EFE heater (monitor)
Heated oxygen sensor-1
Intake air temp sensor
Power steering pressure switch (if equipped)
Engine start signal circuit
C01
1. CMP sensor (in Distributor)
2. CKP sensor
3. TP sensor
4. MAP sensor
5. ECT sensor
6. IAT sensor
7. HO2S-1
8. HO2S-2
9. Transmission range switch (A / T)
10. VSS (A / T)
11. A / C control module (if equipped)
12. Heater blower switch
13. Fuel level sensor
14. Speedometer
15. P.SP switch
16. Rear defogger switch
17. Light switch
18. DLC
19. Fuel injector20. Injector resistor
21. Conister purge valve
22. Fuel pump relay
23. Rediator fan relay
24. EFE heater relay
25. ISC actuator relay
26. ISC actuator
27. Ignition coil
28. Igniter
29. Immobilizer indicator lamp
30. MIL
31. Main relay
32. Shift solenoid A (A / T)
33. Shift solenoid B (A / T)
34. Starter motor
35. Ignition switch

6E1-12 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
1. Fuel injector wire
2. Fuel injector
3. Upper O-ring
4. Lower O-ring
5. Throttle upper body
6. Gasket
7. Throttle lower body
8. ISC actuator
9. TP sensor
10. Injector sub wire coupler
11. O-ring
12. Injector wire cover
CAUTION:
As throttle stop screw and throttle lever screw are fac-
tory adjusted precisely, don’t remove or adjust them.
Throttle
stop
screw
Throttle lever
screwPositive
terminal Negative
terminal
Viewed from “A”
1. Throttle body
2. Vacuum nozzle
1. Injector coupler
2. TP sensor
3. Water hose
4. Vacuum hose
5. ISC actuator
6. Fuel return hose
7. Fuel feed hose
THROTTLE BODY
ON-VEHICLE INSPECTION

Check that throttle valve lever moves smoothly.

Vacuum passage inspection.
With fingers placed against vacuum nozzle, increase engine
speed a little and check that vacuum is applied.
REMOVAL
1) Relieve fuel pressure, referring to Section 6.
2) Disconnect battery negative cable at battery.
3) Remove air cleaner assembly referring to Section 6A.
4) Drain cooling system.
5) Disconnect following wire harness couplers:

TP sensor

Fuel injector

ISC actuator
6) Disconnect following hoses from throttle body.

Fuel feed and return hoses

Engine cooling water hoses

Vacuum hoses
7) Disconnect accelerator cable from throttle valve lever and cable
bracket.
8) Remove throttle body from intake manifold.

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-13
1. Fuel injector wire
2. Fuel pressure regulator
3. TP sensor
4. Screws
5. ISC actuator
1. Injector chamber
2. Fuel return passage
3. Fuel feed passage
4. Vacuum passage for fuel pressure regulator
5. Vacuum passage for MAP sensor
6. Air induction passage
7. Vacuum passage
8. Fresh air passage
DISASSEMBLY
NOTE:

Be sure not to remove either fuel pressure regulator or idle
speed control actuator from throttle body. They are factory
adjusted precisely.

Be sure to replace gaskets and O-rings as well as worn or
damaged parts.

While disassembling and assembling throttle body, use spe-
cial care not to deform levers on throttle valve shaft or cause
damage to any other parts.
1) Remove fuel injector from throttle body according to procedure
described in FUEL INJECTOR REMOVAL.
2) Remove TP sensor.
3) After removing screws, separate upper and lower bodies.
CLEANING
Clean passages and fuel injector chamber by blowing compressed
air.
NOTE:

TP sensor, fuel pressure regulator, fuel injector, ISC actua-
tor, other components containing rubber (resin) or throttle
valve shaft seal must not be placed in a solvent or cleaner
bath. Chemical reaction will cause these parts to swell, hard-
en or get distorted.

Don’t put drills or wires into passages for cleaning. It causes
damage in passages.