2000 SUZUKI SWIFT oil level

6A-2 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
ON-VEHICLE SERVICE
ENGINE VACUUM CHECK
The engine vacuum that develops in the intake line is a good indica-
tor of the condition of the engine. The vacuum checking procedure
is as follows:
1) Warm up engine to normal operating temperature.
2) With engine stopped, remove blind plug hose from intake man-
ifold and connect special tool (vacuum gauge and joint) to va-
cated threaded hole.
Special Tool
(A): 09915-67311
3) Run engine at specified idle speed (see Section 6E), and read
vacuum gauge. Vacuum should be within the following specifi-
cation.
Vacuum specification: 52.6 – 65.8 kPa (40 – 50 cm
.Hg,
15.7 – 19.7 in
.Hg) at specified
idling speed
4) After checking, apply sealant to thread of blind plug and install
it to intake manifold.
OIL PRESSURE CHECK
NOTE:
Prior to checking oil pressure, check the followings.

Oil level in oil pan.
If oil level is low, add oil up to Full level hole on oil level
gauge.

Oil quality.
If oil is discolored, or deteriorated, change it.
For particular oil to be used, refer to the table in Section 0B.

Oil leaks.
If leak is found, repair it.
1) Using special tool (Oil filter wrench), remove oil filter.
2) After removing oil filter, remove oil pressure switch (1) from cylin-
der block.

6A-20 ENGINE MECHANICAL (G10, 1-CAM 6-VALVES ENGINE)
CAUTION:

Don’t turn camshaft or start engine (i.e., valves should not be operated) for about half an hour after
reinstalling hydraulic valve lash adjusters and camshaft. As it takes time for valves to settle in place,
operating engine within half an hour after their installation may cause interference to occur between
valves and piston.

If air is trapped in valve lash adjuster, valve may make tapping sound when engine is operated after
valve lash adjuster is installed. In such a case, run engine for about half an hour at about 2,000 – 3,000
r / min., and then air will be purged and tapping sound will cease. Should tapping should not cease,
it is possible that valve lash adjuster is defective. Replace it if defective.
If defective adjuster can’t be located by hearing among 6 of them, check as follows.
1) Stop engine and remove cylinder head cover.
2) Push adjuster downward by hand (with less than 15 kg or 33 lbs force) when cam crest is not on
adjuster to be checked and check if clearance exists between cam and adjuster. If it does, adjuster
is defective and needs replacement.
VALVE LASH ADJUSTER NOISE DIAGNOSIS
In case of the followings, valve lash adjuster noise may be caused by air trapped into valve lash adjusters.

Vehicle is left for 24 hours or more.

Engine oil is changed.

Hydraulic lash adjuster is replaced or reinstalled.

Engine is overhauled.
If noise from valve lash adjusters is suspected, perform the following checks.
1) Check engine oil for the followings.

Oil level in oil pan
If oil level is low, add oil up to Full level hole on oil level gauge.

Oil quality
If oil is discolored, or deteriorated, change it.
For particular oil to be used, refer to Section 0B.

Oil leaks
If leak is found, repair it.

Oil pressure (refer to Oil Pressure Check in this section)
If defective pressure is found, repair it.
2) Run engine for about half an hour at about 2,000 to 3,000 r / min., and then air will be purge and tapping sound
will cease.
3) Should tapping sound not cease, it is possible that hydraulic valve lash adjuster is defective.
Replace it if defective.
If defective adjuster can’t be located by hearing among 16 of them, check as follows.
a) Stop engine and remove cylinder head cover.
b) Push adjuster downward by hand (with less than 20 kg or 44 lbs. Force) when cam crest is not on adjuster
to be check if clearance exists between cam and adjuster.
If it does, adjuster is defective and needs replacement.

ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-7
OIL PRESSURE CHECK
NOTE:
Prior to checking oil pressure, check the following items.

Oil level in oil pan.
If oil level is low, add oil up to Full level mark on oil level
gauge.

Oil quality.
If oil is discolored, or deteriorated, change it.
For particular oil to be used, refer to the table in Section 0B.

Oil leaks.
If leak is found, repair it.
1) Remove oil pressure switch (1) from cylinder block.
2) Install special tool (Oil pressure gauge) to vacated threaded
hole.
Special Tool
(A): 09915-77311
3) Start engine and warm it up to normal operating temperature.
NOTE:
Be sure to place transmission gear shift lever in “Neutral”
(shift selector lever to “P” range for A / T model), and set
parking brake and block drive wheels.
4) After warming up, raise engine speed to 4,000 r / min and mea-
sure oil pressure.
Oil pressure specification:
360 – 440 kPa (3.6 – 4.4 kg / cm
2, 51.2 – 62.6 psi) at 4,000 r / min
(rpm)
5) Stop engine and remove oil pressure gauge.

4. Guide seal
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-29
7) Remove oil pump assembly (1) after removing bolts (2).
DISASSEMBLY
1) Remove oil level gauge guide bolt (3) and pull out guide (2) from
oil pump (1).
2) Remove rotor plate (1).
3) Remove outer rotor (1) and inner rotor (2).
INSPECTION

Check oil seal lip for fault or other damage. Replace as necessary.

(a)
1
2
3
(a)
(a)
6
74
5
(a)
M/TM/T
9
(a)
4
7
(a)
8
1. Right mounting
2. Right mounting
bracket
3. Left mounting
4. Left mounting bracket
5. Left mounting bracket
stiffener6. Rear mounting
7. Rear mounting
bracket
8. Rear torque rod
9. Rear torque rod
bracket
ENGINE MECHANICAL (G13B, 1-CAM 16-VALVES ENGINE) 6A1-67
INSTALLATION
1) Lift engine with transmission into engine compartment, but do
not remove support device.
2) Install engine right mounting to right mounting bracket and stiff-
ener.
3) Install engine left mounting to body.
4) Install rear mounting to body (For M/T model)
Install torque rod (For A/T model)
5) Tighten bolts and nuts of all parts installed in above steps 2),
3) and 4) or 5) to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)
6) Remove support device.
7) Reverse removal procedures for installation of remainder.

Push in each drive shaft joint fully so that snap ring engages
with differential gear or center bearing support.
Use care not to damage oil seal lip when inserting.

Clamp electric wire securely.
8) Adjust clutch pedal free travel by referring to Section 7C. (M / T)
Adjust gear select cable and A / T throttle pressure control
cable, referring to Section 7B. (A / T)
9) Adjust gear shift control lever by referring to Section 7A. (M / T)
10) Adjust accelerator cable play by referring to Section 6E.
11) Refill transmission with gear oil. (A / T fluid for A / T model) by
referring to Section 0B.
12) Refill engine with engine oil by referring to Section 0B.
13) Refill cooling system by referring to Section 6B.
14) Adjust A / C compressor and / or P / S pump drive belt referring
to Section 0B. (if equipped)
15) Check P / S fluid level by referring to Section 3B1. (if equipped)
16) Upon completion of installation, verify that there is no fuel leak-
age, coolant leakage, transmission oil leakage or exhaust gas
leakage at each connection.

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-3
1. Tank pressure control valve
2. Fuel liquid separator
3. Fuel tank
4. Fuel pump
5. Fuel level sensor (gauge)
6. Fuel filter
7. Fuel pressure regulator
8. Throttle body
9. Fuel injector
10. MAP sensor
11. TP sensor
12. ISC actuator
(including CTP switch)
13. PCV valve
14. Exhaust manifold
15. Intake manifold
16. Heated oxygen sensor-117. Warm up three way catalytic
convertor (WU-TWC)
(if equipped)
18. Three way catalytic convertor
19. IAT sensor
20. ECT sensor
21. EFE heater
22. EVAP canister purge valve
23. EVAP canister
24. Heated oxygen sensor-2
25. Radiator fan motor
26. Ignition coil
27. Ignitor
28. Electric load
29. A / C amplifier (if equipped)
30. Camshaft position sensor
31. Crankshaft position sensor32. VSS (on A / T)
33. Transmission range sensor
(switch) (A / T)
34. Shift solenoid-A (A / T)
35. Shift solenoid-B (A / T)
36. Data link connector
37. VSS (in combination meter of
M / T vehicle)
38. PSP switch (if equipped)
39. Malfunction indicator lamp
40. Transmission range sensor
(switch) (A / T)
41. Main (Ignition) switch
42. Main fuse
43. Battery
44. Immobilizer indicator lamp

ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10) 6E1-7
CON-
NECTOR
C02TERMI-
NAL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26ECM ground
Power source (from main relay)
Blank
Blank
Blank
Blank
EVAP canister purge valve
Shift solenoid-B (A / T)
Shift solenoid-A (A / T)
Igniter
Idle speed control actuator
Fuel injector
Injector ground
Power source (from battery)
Power source (from main relay)
Idle speed control actuator relay
Malfunction indicator lamp
Immobilizer indicator lamp
Heater of HO2S-2
Radiator fan relay
Fuel pump relay
Main relay
Blank
Idle speed control actuator
EFE heater relay
Injector groundC031
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22Data link connector
Vehicle speed sensor (+) (A / T)
Vehicle speed sensor (M / T)
Transmission range sensor (switch)“2”
Transmission range sensor (switch)“N”
Transmission range sensor (switch)“P”
Blank
Blank
Heated oxygen sensor-2
Blank
Fuel level sensor (gauge)
Blank
Data link connector
Vehicle speed sensor (–) (A / T)
Transmission range sensor (switch)“L”
Transmission range sensor (switch)“D”
Transmission range sensor (switch)“R”
A / C ON (output) signal for A / C control module
(if equipped)
Electric load signal
A / C (input) signal from A / C control module
(if equipped)
Ignition switch
Blank
Blank CIRCUITCON-
NECTORTERMI-
NALCIRCUIT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16Power source for sensors
Camshaft position sensor (+)
Crankshaft position sensor (+)
Closed throttle position switch
Manifold absolute pressure sensor
Throttle position sensor
Engine coolant temp. sensor
Heater of HO2S-1
Sensor ground
Camshaft position sensor (–)
Crankshaft position sensor (–)
EFE heater (monitor)
Heated oxygen sensor-1
Intake air temp sensor
Power steering pressure switch (if equipped)
Engine start signal circuit
C01
1. CMP sensor (in Distributor)
2. CKP sensor
3. TP sensor
4. MAP sensor
5. ECT sensor
6. IAT sensor
7. HO2S-1
8. HO2S-2
9. Transmission range switch (A / T)
10. VSS (A / T)
11. A / C control module (if equipped)
12. Heater blower switch
13. Fuel level sensor
14. Speedometer
15. P.SP switch
16. Rear defogger switch
17. Light switch
18. DLC
19. Fuel injector20. Injector resistor
21. Conister purge valve
22. Fuel pump relay
23. Rediator fan relay
24. EFE heater relay
25. ISC actuator relay
26. ISC actuator
27. Ignition coil
28. Igniter
29. Immobilizer indicator lamp
30. MIL
31. Main relay
32. Shift solenoid A (A / T)
33. Shift solenoid B (A / T)
34. Starter motor
35. Ignition switch

6E1-24 ENGINE AND EMISSION CONTROL SYSTEM (TBI FOR G10)
VEHICLE SPEED SENSOR (VSS) For M / T
INSPECTION
1) Disconnect negative cable at battery.
2) Remove combination meter from instrument panel.
3) Connect ohmmeter between “VSS” terminal (2) and “GND” ter-
minal (3) of combination meter and turn cable joint (1) of
speedometer with a screwdriver. Ohmmeter indicator should
move back and forth between 0 (zero) and ∞ (infinity) 4 times
while cable joint is turned one full revolution.
Replace speedometer if check result is not satisfactory.
4) Install combination meter to instrument panel.
5) Connect negative cable at battery.
VEHICLE SPEED SENSOR (VSS) For A / T
INSPECTION
Vehicle speed sensor (1) itself can be checked on its resistance by
disconnecting connector.
NOTE:

Function of vehicle speed sensor can be checked by mea-
suring generated pulse as voltage.

For its measurement, use an analog type voltmeter while
spinning wheels on lift and with selector lever in D position.
Vehicle speed sensor specifications
Coil resistance100 – 300 Ω
Output voltage at 40 km / h (25 mile / h)approximately 1 V
FUEL LEVEL SENSOR (GAUGE)
Refer to Section 8.